Andersen Passive Panel Replacement Service Instructions

Brand: Andersen

Model: Passive Panel Replacement

Type: Service Instructions

9069252 BA Revised 10/16/13

Passive Panel Replacement

for E-Series Hinged Inswing and Outswing Patio Doors with Type III Hardware

Thank you for choosing Andersen.

For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.

Please leave this guide with building owner.

▶Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.

Parts Included

(1) Passive Panel

Passive Panel

Tools Needed Herramientas necesarias

∙Safety Glasses Lentes de seguridad

∙Drill/Driver

∙#2 Phillips Bit

∙2.5 mm Hex Key

∙#2 Phillips Screwdriver P

∙Caulk Gun s Screwdriver

Use caution when working at elevated heights and around unit openings. Follow

manufacturers’ instructions for ladders and/or scaffolding. Failure to do so may

result in injury or death.

Sea cauteloso al trabajar en lugares elevados y cerca de las aberturas de la unidad.

Siga las instrucciones del fabricante para el uso de escaleras y/o andamios. Si no lo

hiciera, podrían producirse lesiones o la muerte.

Follow manufacturers’ instructions for hand or power tools.

Always wear safety glasses. Failure to do so may result in injury

and/or product damage.

Siga las instrucciones del fabricante para el uso de herramientas

eléctricas o manuales. Utilice siempre gafas de seguridad. Si no

lo hiciera, podrían producirse lesiones y/o daños al producto.

Windows and doors can be heavy. Use safe lifting techniques and a reasonable number

of people with enough strength to lift, carry and install window and door products to avoid

injury and/or product damage.

Las puertas y las ventanas pueden ser pesadas. Utilice técnicas seguras de levantamiento

de peso y un número razonable de personas con suficiente fuerza para levantar, cargar e

instalar los productos de puertas y ventanas, a fin de evitar lesiones y/o daños al producto.

Panel must be supported during entire removal and

installation procedures. Failure to support sash may result in

injury and/or product damage.

La hoja debe sostenerse durante todo el proceso de

extracción e instalación. De no sostenerla, podrían

producirse lesiones y/o daños al producto.

▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.

Supplies Needed

∙Sealantentes de seguridad

9069252

Open passive door by rotating thumb turn to unlock hardware. Then push down on handle to open

passive panel.

Remove interior and exterior handle/escutcheon plates and save for reuse.

Interior

Open active door panel.

Interior Escutcheon Plate Exterior Escutcheon Plate

2.5mm Hex Key

Handle

Remove two (2) escutcheon plate screws with a drill/driver and save

for reuse.

Escutcheon

Plate Screws

Escutcheon

Plate Screws

Drill/

Driver

Loosen handle set screw with a 2.5 mm hex key.

Active

Door

Panel

Passive

Door

Panel

Exterior Thumb

Turn

Exterior View

Passive Panel

Interior Views

9069252

Remove center strike plate and dust cup and save for reuse. Remove top and bottom strike plates and dust cups and save for reuse.

Support passive panel before removing panel hinge screws.

Weight of window/door

unit(s) and accessories

will vary. Use a

reasonable number of

people with sufficient

strength to lift, carry, and

install window and door

unit(s) and accessories.

Always use appropriate

lifting techniques.

Remove screws attaching top, center and bottom strike plates. Save screws for reuse.

Center Strike Plate Top and Bottom Strike Plates

Center Strike Plate

Dust Cap

Active

Door

Panel

Passive

Door

Panel

Drill/DriverDrill/Driver

Top and Bottom

Strike Plates

Top and Bottom Strike

Plate Dust Caps

Exterior

9069252

Drill/

Driver

Drill/

Driver

Passive

Panel

Passive

Panel

#12 x 1 1/2"

Screws

#12 x 1 1/2"

Screws

Hinge Cup

Hinge Shims

Note position

and quantity.

Note position

and quantity.

Reapply saved center strike plate and dust cup. Reapply saved top and bottom dust cups and strike plates. Secure with saved screws.

Position hinge cups and shims in hinge routs on new panel at locations

noted in previous step. Hold shims in place with a dab of sealant.

Remove four (4) #12 x 1 1/2" screws from each hinge on panel and

save for reuse. Place panel upright against a stable surface.

Interior

Note position and quantity of shims in hinge routes. Remove hinge

cups and shims from each hinge route and save for reuse.

Support door panel at all times while attaching panel to hinges on frame

using screws saved from previous step.

Center Strike Plate

Dust Cap

Top and Bottom

Strike Plates

Top and Bottom Strike

Plate Dust Caps

Exterior

If replacing an

outswing panel

apply a light coat of

silicone to all hinge

routes on panel

before reapplying

hinge cups.

9069252

2.5mm Hex Key

Handle

Close passive door panel. Lock door panel by rst lifting up on handle, then turning thumb turn

counterclockwise.

Align handle spindle with slot in lock mechanism and position exterior

escutcheon plate/gasket assembly against door panel.

Interior

▶Passive panel replacement is completed.

Close and lock active door panel. Check for

correct lock operation.

Interior

Escutcheon

Plate

Interior

Escutcheon

Plate

Exterior

Escutcheon

Plate/

Gasket

Handle

Spindle

Door

Panel

Plate

Drill/Driver

Interior

Place interior escutcheon assembly against door panel with tail piece

on thumb turn aligned with slot in lock mechanism. Check for proper

operation of thumb turn.

Fasten interior escutcheon plate using saved screws. Tighten handle set screw with a 2.5 mm hex key.

Remove two (2) escutcheon plate screws and dispose of properly.

Thumb

Turn

Handle

Interior

Views

Exterior

Exterior View

Andersen Passive Panel Replacement Service Instructions

Andersen Passive Panel Replacement Service Instructions

Andersen Passive Panel Replacement Service Instructions

Related papers

Other documents