Andersen Operating Panel Replacement Service Instructions
- Type
- Service Instructions
9069166 BA Revised 09/24/13
Tools Needed
∙Safety Glasses
∙Phillips Screwdriver
∙Drill/Driver
∙#2 Phillips Bit
Operating Panel Replacement
for E-Series Gliding Patio Doors
Use caution when working at elevated heights and around unit openings.
Follow manufacturers’ instructions for ladders and/or scaffolding. Failure
to do so may result in injury or death.
Follow manufacturers’ instructions for hand or power tools. Always
wear safety glasses. Failure to do so may result in injury and/or
product damage.
Parts Included
(1) Operating Panel
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.
Please leave this guide with building owner.
▶Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.
Operating Panel
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved.
Panel must be supported during entire removal and installation
procedures. Failure to support sash may result in injury and/or
product damage.
Windows and doors can be heavy. Use safe lifting techniques and a
reasonable number of people with enough strength to lift, carry and
install window and door products to avoid injury and/or product
damage.
Unlock and open operating panel.
Operating Panel
Remove visible head track screws and save for reuse.
1
Interior
2
Interior
Head Track
Head Track Screw
Drill/Driver
2
9069166
Operating Panel
3
Interior
4
Interior
Close and lock operating panel. Remove remaining head track screws and save for reuse.
Head Track
Head Track Screw
Drill Driver
Unlock and open operating panel half-way.
5
Interior
Tip top of operating panel and head track panel stop inward from frame.
Lift head track panel stop from top of panel and save for reuse.
6
Interior
Head Track Panel Stop
Operating Panel
Head track rests on
top of operating panel.
Operating Panel
3
9069166
Lift operating panel out of frame.
7
Interior
Operating Panel
Remove two (2) escutcheon plate screws and save for reuse.
Remove interior and exterior handle/escutcheon plate and
save for reuse.
8
Interior
9
Interior
Escutcheon Plate
Escutcheon
Plate Screws
Interior
Escutcheon
Plate
Exterior
Escutcheon
Plate
Remove lock lever and save for reuse.
10
Interior
Lock Lever
Remove two (2) lock mechanism screws and save for reuse.
11
Interior
Drill/Driver
Lock
Mechanism
Lock Mechanism
Screws
Remove lock mechanism and save for reuse.
12
Interior
Lock
Mechanism
4
9069166
Fasten lock mechanism using two (2) saved screws.
Insert lock mechanism on new panel with actuator pin down.
13
Interior
14
Interior
Lock
Mechanism Actuator Pin
Drill/Driver
Lock
Mechanism
Lock Mechanism
Screws
15
Interior
Position lock lever into lock mechanism.
Lock Lever
16
Interior
Apply interior and exterior handle/ escutcheon plate.
Interior
Escutcheon
Plate
Exterior
Escutcheon
Plate
Fasten escutcheon plate using saved screws.
17
Interior
Escutcheon Plate
Escutcheon
Plate Screws
Center operating panel into frame with rollers on sill track. Tip top of
operating panel slightly inward.
18
Interior
Operating Panel
5
9069166
Place head track/panel stop on top of operating panel with panel stop
facing interior.
19
Interior
Tip top of operating panel back into frame.
20
Interior
Head Track Panel
Stop
Operating Panel
Close and lock operating panel.
21
Interior
Operating Panel
Head Track
Head Track
Screw
Drill Driver
Fasten head track with saved screws on
stationary panel side.
22
Interior
Unlock and open operating panel.
Operating Panel
23
Interior
Fasten head track with remaining saved screws on operating panel side.
24
Interior
Head Track
Head Track Screw
Drill/Driver
Operating Panel
Close and lock operating panel. Check for correct lock operation.
25
Interior
▶Operating panel replacement is completed.
Head Track Panel Stop
Head Track
Panel Stop
-
1
-
2
-
3
-
4
-
5
Andersen Operating Panel Replacement Service Instructions
- Type
- Service Instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Andersen Active Door Panel Replacement Service Instructions
-
-
-
-
-
-
-
-
-
