Andersen 400 Series - Frenchwood® Hinged - 0005516 Service Instructions

Brand: Andersen

Model: 400 Series - Frenchwood® Hinged - 0005516

Type: Service Instructions

Please read this guide completely before starting. For questions about this and other Andersen® products, call 1-888-888-7020.

For the most current version of this guide visit www.andersenwindows.com. Consult your local building code official for

applicable building codes and regulations. Thank you for choosing Andersen® products.

Please leave this information with homeowner.

Stainless Steel Passive Lock

Mechanism Conversion Guide

for Andersen® 400 Series Frenchwood® Hinged and Outswing Patio Doors

0005516 BA Revised 09/18/07

Tools Needed

· Safety Glasses

· Hex Wrench

· Power Drill

· Pencil

Parts Included

(1) Instruction Guide

(1) Stainless Steel Passive Lock Mechanism

Outswing Package

(2) Hook Bolt Receiver

(2) Flush Bolt Receiver

(1) Lock Mechanism Blocker

(1) Latch Receiver Blocker

Inswing Package

(2) Hook Bolt Receiver

(2) Flush Bolt Receiver

(1) Lock Mechanism Blocker

(1) Latch Receiver Blocker

Use caution when working at elevated

heights and around unit openings. Follow

manufacturer’s instructions for safe use of

ladder and/or scaffolding. Failure to do

so may result in injury or death.

Follow manufacturer’s instructions for safe

operation of hand/power tools. Always

wear safety glasses. Failure to do so may

result in injury and/or product damage.

Astragal

Active Panel

(Operating

panel most

commonly used)

Passive Panel

(Operating

panel with

astragal attached)

Hook Bolt

Receivers

Flush Bolt

Receivers

Latch

Receiver

Blocker

(upper)

Inswing Package

Lock

Mechanism

Blocker Cap

(lower)

(head)

(sill)

Outswing Package

Hook Bolt

Receivers

Flush Bolt

Receivers

Latch

Receiver

Blocker

(upper)

Lock

Mechanism

Blocker Cap

(lower)

(head)

(sill)

Stainless Steel

Passive Lock

Mechanism

· Utility Knife

· 3/8 Drill Bit

• PhillipsScrewdriver

Read and follow these warnings during installation.

Interior

Exterior

Loosen set screw on underside of exterior handle and remove

handles. Keep all hardware and fasteners for reinstallation.

Remove escutcheon plate bolts, interior and exterior escutcheon

plates and gasket. Keep these parts for reinstallation.

Support handles during removal. Support both escutcheon plates when loosening bolts.

0005516

Remove hook bolt receivers and latch receiver. Retain latch receiver and all screws for reuse. Properly discard hook bolt receivers.

Frenchwood® Outswing Patio Door Frenchwood® Inswing Patio Door

Escutcheon

Plate Bolt

Interior

Escutcheon

Plate

Interior

Handle

Exterior

Handle

Hex

Wrench

Set

Screw

Gasket

Exterior

Escutcheon

Plate

Hook Bolt

Receivers

Hook Bolt

Receiver

Strike Plate

Hook Bolt

Receiver

Hook Bolt

Receiver

Latch

Receiver

Phillips

Screwdriver

Interior

Exterior

0005516

Lock Mechanism

Remove lock mechanism. Retain screws for reuse.Pull astragal outwards to remove. Break paint or varnish seal

between astragal and panel, if needed, using a utility knife.

Frenchwood® Outswing Patio Door

Frenchwood® Inswing Patio Door

Astragal

Utility

Knife

Astragal

Utility

Knife

Interior

0005516 4

Lock Mechanism

Insert lock mechanism into door panel and secure using existing

screws in all countersunk holes. Use ﬁve screws for 8'-0" units.

Use four screws for 6'-8" and 6'-11" units.

Lock Mechanism

Snap blocker cap over blocker pin.

Lock Mechanism Blocker Cap

Frenchwood® Outswing Patio Door

Lock Mechanism Blocker Cap

Frenchwood® Hinged Patio Door

Identify proper lock mechanism blocker cap to use. Properly

discard unused blocker cap.

Lock

Mechanism

Blocker Cap

Blocker Pin

Interior

Exterior

0005516

Frenchwood® Inswing Patio Door

Position astragal onto panel. Fasten at head and sill through hook bolt receivers using screws removed in step 3. Make sure

adjustment tabs are toward the interior of frame for inswing door and toward the exterior for outswing door.

3/8"

Drill Bit

Hook Bolt

Receiver

Plug

Clearance Hole

3/8"

Drill Bit

Hook Bolt

Receiver

Frenchwood® Outswing Patio Door

Inswing patio door astrgal shown.

Power

Drill

Astragal

Adjustment

tab toward

exterior

Adjustment

tab toward

interior

Position plugs on new hook bolt receiver into existing receiver screw holes near top and bottom ends of astragal. Drill 3/8" clearance

holes through astragal using receiver as a template. Repeat on each side and at both ends of astragal.

Hook Bolt

Receiver

Phillips

Screwdriver

Hook Bolt

Receiver

Phillips

Screwdriver

Interior

Exterior

0005516 6

Frenchwood® Inswing Patio Door

Frenchwood® Outswing Patio Door

Frenchwood® Inswing Patio Door Frenchwood® Outswing Patio Door

Latch

Receiver

Existing Latch Receiver Blocker

New Latch

Receiver

Blocker

Reinstall latch receiver on astragal using screws removed in step 3.

Latch

Receiver

Existing Latch Receiver Blocker

New Latch

Receiver

Blocker

Replace existing latch receiver blocker on latch receiver with new latch receiver blocker.

Latch

Receiver

Astragal

Latch Receiver

Astragal

Interior

Interior Exterior

Exterior

0005516 7

Replace existing ﬂush bolt receiver at sill with new ﬂush bolt receiver using existing screws. Make sure adjustment tabs are toward

interior side for inswing door and toward the exterior side for outswing door.

Frenchwood® Inswing Patio Door Frenchwood® Outswing Patio Door

Replace existing ﬂush bolt receiver at head with new ﬂush bolt receiver using existing screws.

Frenchwood® Inswing Patio Door Frenchwood® Outswing Patio Door

New

Flush Bolt

Receiver

Existing

Flush Bolt

Receiver

Sill

New Flush

Bolt Receiver

Sill

Existing

Flush Bolt

Receiver

Sill

New Flush

Bolt Receiver

Sill

Existing

Flush Bolt

Receiver Head

Jamb

Head

Jamb

New

Flush Bolt

Receiver

Existing

Flush Bolt

Receiver

Head

Jamb

Head

Jamb

Adjustment

tab toward

exterior

Adjustment

tab toward

interior

Interior

0005516

Reapply trim set reversing steps 1 and 2. Check hardware operation.

4 Test door lock operation.

4 If latch bolt does not engage latch

receiver, adjust latch receiver

blocker following steps below.

Escutcheon Plate Bolts Interior Handle

Hex Wrench

Set Screw

Exterior Escutcheon Plate

Interior

Escutcheon Plate

Gasket

Interior Handle

Support handles

and escutcheon

plates when

securing.

Mark where top of latch bolt strikes latch receiver on edge of

passive panel using a pencil.

Loosen blocker adjustment screw. Slide until lower surface of

blocker is 1/4" above pencil mark. Retighten blocker

adjustment screw. Recheck hardware operation.

Pencil Mark

Top Edge of

Latch Bolt

Latch

Receiver

Passive Panel

Active Panel Latch

Receiver

Lower Surface

of Blocker

Blocker

Adjustment

Screw

Lower Surface of

Blocker 1/4"

Above Pencil

Mark

Pencil Mark

Blocker Adjustment

Andersen 400 Series - Frenchwood® Hinged - 0005516 Service Instructions

Andersen 400 Series - Frenchwood® Hinged - 0005516 Service Instructions

Andersen 400 Series - Frenchwood® Hinged - 0005516 Service Instructions

Related papers

Other documents