Andersen Windows & Doors FSB 1035 Instructions Manual
- Type
- Instructions Manual
FSB® Hardware Handle Styles
Product Series:
- E-Series (Inswing & Outswing)
- E-Series Stormwatch (Inswing & Outswing)
- A-Series Frenchwood (Inswing & Outswing)
- A-Series Frenchwood Stormwatch (Inswing)
- 400 Series Frenchwood (Inswing & Outswing)
- 200 Series (Inswing)
- Complementary Curved Top (Inswing & Outswing)
- Folding Doors
- Residential Entry Doors with Multi-Point Lock
(Inswing & Outswing)
Product Type: Hinged Doors
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2020 Andersen Corporation. All rights reserved. 9173980 BC-00 02/11/2020
FSB
®
Trim Set Hardware Application
FSB 1035 hardware style shown in guide.
Procedure is similar for all styles.
for Active and Passive Hardware
Active hardware application shown in guide.
Procedure is similar for passive hardware.
Spanish Version is
9174221
FSB 1102
FSB 1035
FSB 1075
FSB 1076
Read these instructions before starting procedure. For additional information visit www.andersenwindows.com. For questions call 1-888-888-7020.
Para obtener una versión en español de esta guía, visite el sitio andersenwindows.com/accessory guides
WARNING
Passive
Hardware
Before installing hardware, install door panels and nish interior wood
surfaces of unit.
NOTICE
Active
Hardware
(with interior
thumb turn knob)
· Use caution when working at elevated heights and around window
and door openings. Follow the manufacturers’ instructions for ladders
and scaffolding. Failure to do so could result in injury or death.
· Follow manufacturers’ instructions for hand and power tools. Always
wear safety glasses. Failure to do so could result in injury, product or
property damage.
· Incorrect installation may affect egress and home security. Follow
instruction guide to make sure hardware is installed correctly.
· Windows and doors have small parts (e.g. hole plugs, operator spline
caps, fasteners, etc.). Small parts if swallowed could pose a choking
hazard to young children. Dispose of unused, loose, or easily removed
small parts. Failure to do so could result in injury.
Tools and Supplies Needed:
Safety
Glasses
Phillips
Screwdriver
Caulk Gun
Sealant
Interior
Handle
2
9173980
Passive Hardware
(AP/PA Kits ONLY)
(1) Interior Escutcheon Plate
(1) Exterior Escutcheon Plate
(2) Escutcheon Base Plate
(2) Escutcheon Base Plate Screw
(2) Escutcheon Base Plate
Sleeve Nut
(1) Spindle
(1) Interior Handle
(1) Exterior Handle
(2) Set Screw
(1) 3 mm Hex Key
Active Hardware
(1) Interior Escutcheon Plate
(1) Exterior Escutcheon Plate
(2) Escutcheon Base Plate
(2) Escutcheon Base Plate Screw
(2) Escutcheon Base Plate
Sleeve Nut
(1) Spindle
(1) Interior Handle
(1) Exterior Handle
(2) Set Screw
(1) 3 mm Hex Key
(1) Latch Strike Plate
(2) Receiver Screw
(1) Lock Actuator
(1) Limiting Plate
(2) Limiting Plate Screw
(1) Screw Retainer
Keyed Lock Exterior
Escutcheon Plate
Exterior Keyed
Lock Gasket
Exterior Keyed Lock Kit
(optional)
(1) Keyed Lock Exterior
Escutcheon Plate
(1) Exterior Keyed Lock Gasket
3 mm
Hex Key
Exterior
Escutcheon
Plate
Screw
Retainer
ACTIVE
Interior
Escutcheon
Plate
Escutcheon
Base Plate
Sleeve Nuts
Escutcheon Base
Plate Screws
Spindle
3 mm
Hex Key
Set
Screw
Set
Screw
Set
Screw
Set
Screw
Spindle
Spindle
Lock
Actuator
Single Active Latch Strike Plate
-A-Series Frenchwood
®
(Inswing),
-400 Series Frenchwood (Inswing),
-Andersen Complementary (Inswing)
Color
Matched
Latch
Receiver
Screws
AP/PA Latch Strike Plate
-A-Series Frenchwood
®
(Inswing),
-400 Series Frenchwood (Inswing)
Parts Included:
Additional Parts Included:
Limiting
Plate
Escutcheon
Base Plate
Escutcheon
Base Plate
Limiting
Plate
Screws
Escutcheon
Base Plate
Exterior
Escutcheon
Plate
Exterior
Handle
Escutcheon
Base Plate
Sleeve Nuts
Interior
Handle
Escutcheon
Base Plate
Screws
Escutcheon
Base Plate
Spindle
Exterior
Handle
PASSIVE
Interior
Escutcheon
Plate
3
9173980
2
Insert limiting plate screws and screw retainer as shown. Hold screw retainer on the exterior while tightening screws on the interior.
2
1
Insert lock actuator and limiting plate into lock hole on interior side of
door panel as shown.
Construction handle set
components cannot be used
with standard trim sets.
Remove all construction
handle set components
before installing FSB trim set
hardware.
IMPORTANT
Screw
Retainer
If optional exterior
keyed lock is being
installed with patio
door hardware,
substitute cylinder
assembly in place of
screw retainer.
NOTICE
Exterior
Keyed Lock
Cylinder
Assembly
Active Hardware Application Only
Active Hardware Application Only
4
9173980
Fill bottom screw hole with sealant as shown. Position escutcheon base plates over spindle on both sides. Fasten using escutcheon base plate
screws and sleeve nuts as shown. (DO NOT fully tighten screws until escutcheon base plates are straight up and down.)
3
Escutcheon base plate screws
must be installed from interior and
sleeve nuts from exterior to prevent
tampering with the handle set from
the exterior.
CAUTION
Escutcheon Base
Plate Sleeve Nuts
(exterior side)
(side view)
Escutcheon Base
Plate Screws
(interior side)
NOTICE
For optional exterior keyed lock
hardware, make sure exterior keyed
lock gasket is positioned securely to
the exterior escutcheon base plate
before applying to panel, as shown.
Exterior
Keyed Lock
Gasket
(for optional
exterior keyed
lock)
DO NOT overll hole
with sealant or allow
sealant to seep out
the other side.
5
9173980
Position interior and exterior escutcheon plates over the escutcheon base plates as shown. Apply rm pressure to top and bottom ends until
attachment clips engage.
4
Partially insert set screw into hole on bottom of handles. Slide handles onto spindle, tight to escutcheon plate. Tighten set screws on both handles
using 3 mm hex key.
5
Attachment
Clip
Attachment
Clip
Apply rm pressure to top and
bottom ends of both escutcheon
plates to engage attachment clips.
Handles must point toward the glass
with set screw on the bottom.
Partially insert
set screw before
applying handle
to panel.
6
9173980
6
Check operation. If handles do not seat or operate smoothly, loosen
interior set screw one-quarter turn at a time until handles operate
smoothly.
▶ For A-Series Frenchwood® Hinged Patio Doors (Outswing)
and 200 Series Hinged Patio Doors (Inswing), discard remaining
latch strike plate. Active trim set hardware application is
complete.
▶ For A-Series Frenchwood® Hinged Patio Doors (Inswing) and
400 Series Frenchwood® Hinged Patio Doors (Inswing) proceed
to next step.
NOTICE
Label on edge of panel
describes lock operation.
General Information
Your Andersen
®
hardware has been manufactured of high quality, ne
metal. Fine metal requires periodic attention to maintain its beauty and
characteristics. Climate, location, and exposure to corrosive environments
such as industrial areas, pesticides, herbicides, or salts are challenges to
your ability to maintain the hardware’s beauty and characteristics.
Wash hardware using a mild detergent and a soft cloth to remove mild stains, loose dirt, and soil. Avoid abrasive cleaners, cloths,
or brushes. When mild detergent and a soft cloth are not adequate, a diluted, household vinegar solution (5%) and a soft bristled,
non-abrasive brush may be used. Avoid contact with painted components and nearby surfaces. After cleaning, wipe down with a
damp cloth and wipe dry to prevent spots.
Satin Stainless Steel
Care and Maintenance
Do not use or apply harsh chemicals, abrasives
and/or cleaners. Product damage could occur.
Do not refurbish hardware. Contact a professional
hardware restorer for refurbishing.
7
9173980
▶ Procedure is complete.
Remove existing latch receiver screws from latch receiver and dispose of properly. Position latch strike plate over latch receiver and fasten with
color matched latch receiver screws (provided).
7
NOTICE
Frenchwood
®
Patio Door latch strike plates differ for active doors versus active-passive/
passive-active two panel doors. Follow procedure for your type of door.
▶ For passive hardware application for AP/PA doors: follow steps 3 - 7.
CAUTION
A-Series Frenchwood® Hinged Inswing and 400 Series Frenchwood Hinged Inswing Patio Doors Only
AP/PA Unit
(Passive Panel)
Active Unit
(Jamb)
Color Matched
Latch Receiver
Screws (provided)
Color Matched
Latch Receiver
Screws (provided)
Latch
Receiver
Latch
Strike
Plate
Latch
Receiver
Screws
Latch
Receiver
Screws
Latch
Receiver
Latch
Strike
Plate
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Andersen Windows & Doors FSB 1035 Instructions Manual
- Type
- Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Armor Door VSDFPEX3680EL Operating instructions
-
Andersen Handle Replacement Service Instructions
-
Barton Kramer 1802 Installation guide
-
-
-
-
-
-
-
GE GPF610W Installation guide
