2. TRAN LED
  3. Q-CAP
Q-CAP

TRAN LED Q-CAP Installation guide

  • Hello! I've reviewed the installation instructions for the Q-Tran Flexible Fixture WALA. This document outlines various mounting options, including VHB adhesive, snug clips, and PVC channels, and describes how to achieve seamless connections. I'm ready to answer your questions about the installation process or features mentioned in the document.
  • How often should white snug clips be placed?
    What type of screw is used for mounting the white snug clip?
    Can the PVC mount channels be cut in the field?
    What is the purpose of the PPS-BRACKET?
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-28-21
INSTALLATION Q-CAP Flexible Fixtures: WALA
1.
1.
2.
2.
3.
3.
12"
.07"
VHB MOUNTING
WHITE SNUG CLIP
Align fixture to white snug clips matching distances. Press fixture into white snug clips.
Mount white snug clip with provided flat head screw.
Peel off secondary backing.Remove the backing from the adhesive and apply firm pressure to
the bonding surface.
Adhere to mounting surface.
#4x5/8" Flat head screw
.25”
.44”
.50”
NOTE: White snug clip should be placed every 12"
INCLUDED HARDWARE
.21
"
.625"
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-28-21
INSTALLATION Q-CAP Flexible Fixtures: WALA
Press both fixtures into PPS clip.
2.
Snap fixture into mounted PPS channel
When wire will exit into conduit do not install bracket.
1.
Mounting Feed
3.
Finished Assembly for seamless bottom feed mounting (S5,S6/P5,P6).
Power Supply
PVC MOUNT CLIP: Connects two seamless fixtures, with or without wire exit
WALA-PPS-2
Press in fixtures
1.
Snap in 2" channel
2.
Mounting Feed
LOW PROFILE PVC MOUNT CLIP: Connects two seamless fixtures, with or without wire exit
WALA-PPS-LP-2
3.
Finished assembly for end feed mounting (S1/P1).
Power Supply
.47”
.56”
2.00”
.46"
2.0"
.94
"
2.0
"
.56
"
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-28-21
INSTALLATION Q-CAP Flexible Fixtures: WALA
3.
5.
1.
The PPS-BRACKET can be field cuttable and cut to whatever length your
application requires. The PPS-BRACKET can be installed as a full length of
96", multiple smaller pieces, or end to end for longer seamless runs.
To mount, pinch the upper half of the PPS-96 or PPS-FT while you pivot it
around one side of the PPS-BRACKET and push-in until you hear it snap
into place. The PPS-96 or PPS-FT flexes around the PPS-BRACKET to
create a solid, and secure snap on connection.
16" 16" 16"
2.
4.
The PPS-96 or PPS-FT can be field cuttable and cut to whatever length your
application requires. The PPS-96 or PPS-FT can be installed as a full length
of 96", multiple smaller pieces, or end to end for longer seamless runs.
2" or more
PVC MOUNT CHANNEL: Support for the fixture
C O V E
.60"
.95"
Cut out area
Cove install
The PPS-BRACKET
allows you to create
a wire way under
the PPS channel
without any screws
interfering
Built in wireway:
#6 Flat head screw
.26
"
1"
PPS - BRACKET:
Sold in full length of 96"
or custom length (FT)
Using pre-drilled pilot holes, use the #6 flat head screws to mount the
PPS-BRACKET.
Using pre-drilled pilot holes screw the #6 flat head screws to mount the
PPS-BRACKET (1 screw every 16").
NOTE : For drywall applications mount directly into a stud.
WALA-PPS-96 & WALA-PPS-FT
- 96" (PPS-96) or custom length (PPS-FT)
INCLUDED HARDWARE
.94
"
96
" / FT
.56"
.46"
96" / FT
#6 Flat head screw
.26
"
1"
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-28-21
INSTALLATION Q-CAP Flexible Fixtures: WALA
3.
LOW PROFILE PVC MOUNT CHANNEL: Support for the fixture
Using pre-drilled holes, use the #6 flat head screws to mount the PPS-LP.
NOTE : For drywall applications mount directly into a stud.
4.
Snap fixture into PPS-LP.
.48"
C O V E
.57"
Cut out area
Cove install
16" 16" 16"
2.
WALA-PPS-LP-96 & WALA-PPS-LP-FT
Drill holes (1 hole/screw every 16") into the PPS-LP.
INCLUDED HARDWARE
- 96" (PPS-96) or custom length (PPS-FT)
.47”
.56”
96”/FT
1.
The PPS-LP-96 or PPS-LP-FT can be field cuttable and cut to whatever
length your application requires. The PPS-96 or PPS-FT can be installed
as a full length of 96", multiple smaller pieces, or end to end for longer
seamless runs.
2" or more
#6 Flat head screw
.26
"
1"
#6 Flat head screw
.26
"
1"
/