2. Q-tran
  3. Q-TRAN QZLP LED Power Supply
Q-TRAN QZLP LED Power Supply

Q-tran Q-TRAN QZLP LED Power Supply, QZLP LED Power Supply User manual

  • Hello! I've reviewed the installation instructions for the Q-Tran QZLP LED Power Supply. This document outlines how to properly mount and wire the QZLP, covering topics such as vertical and horizontal mounting, spacing requirements for multiple units, dimming options, and wiring diagrams. I'm ready to assist with any questions you have about this LED power supply.
  • Can the QZLP be mounted in any orientation?
    How much space is required when installing multiple QZLP power supplies?
    What dimming options are supported by QZLP?
    What is the voltage adjustment required for the LEDs?
INSTALLATION LED POWER SUPPLY - QZLP
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-10-12-21
1 3 42
QZLP Components
Driver Compartment Primary Compartment Secondary Compartment Mounting Tab Slots
3
2
1
4
4
TOP VIEW
DRIVER COMPARTMENT
INSTALLATION LED POWER SUPPLY - QZLP
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-10-12-21
Required Hardware
Mounting
• #4 Flat head screw
(not included)
The QZLP must be mounted into a stud for sufficient support, using the slots of each mounting tab
2
SIDE SLOT
The QZLP can be mounted either vertically or horizontally, utilizing the supplied screws and the mounting tabs on the
bottom of the enclosure
1
.21
"
.625"
INSTALLATION LED POWER SUPPLY - QZLP
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-10-12-21
When installing multiple QZLP power supplies, seperate the enclosures by 3” of space from edge to edge. This prevents
the rise of ambient temperature between the power supplies.
3
3.00
"
3.0”
3.0”
Horizontal mount illustrated above Vertical mount illustrated above
INSTALLATION LED POWER SUPPLY - QZLP
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-10-12-21
Wiring diagram
4
Phase Dimming
0-10v Dimming
SRV1
- DIM +
30W
60W
LED
- OUTPUT +
Phase Dimmer
GND
HOTNEU
INPUT
N
L
25W, 30W, 60W
+
-
Volt. Adj.
21.5V 25.5V
DIMMING
0/1-10V
−+−+
LED
OUTPUT
INPUT
L
N
SRV1
- DIM +
30W
60W
LED
- OUTPUT +
0-10V Dimmer
INPUT
N
L
25W, 30W, 60W
DIMMER
GND
HOTNEU
DIMMING
0/1-10V
−+−+
LED
OUTPUT
INPUT
L
N
+
-
Volt. Adj.
21.5V 25.5V
Voltage Adjustment
• Ensure voltage at LEDs is 24V
• Adjust with caution
Voltage Adjustment
• Ensure voltage at LEDs is 24V
• Adjust with caution
Wiring from power supply to light fixture must be two conductor cable
INSTALLATION LED POWER SUPPLY - QZLP
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-10-12-21
QZLP 30W
QZLP 60W
TOP VIEW
TOP VIEW
SIDE VIEW
SIDE VIEW
6.1”
.13”
.2”
6.05”
2.13”
.13”
.2”
.3”
7.00”
2.40”
.13”
.23”
.3”
.80”
.95”
INSTALLATION LED POWER SUPPLY - QZLP
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-10-12-21
QZLP CORD & PLUG 25W
QZLP CORD & PLUG 60W
TOP VIEW
TOP VIEW
SIDE VIEW
SIDE VIEW
72”
INPUT OUTPUT
6”
22 AWG, 2 CONDUCTOR
2.13”
6.05”
72”
22 AWG, 2 CONDUCTOR
2.40”
7.00”
6”
INPUT OUTPUT
.78”
INPUT OUTPUT
.95”
INPUT OUTPUT
/