2. Q-tran
  3. Q-TRAN QZ-STICK-PH-0-10V LED Power Supply
Q-TRAN QZ-STICK-PH-0-10V LED Power Supply

Q-tran Q-TRAN QZ-STICK-PH-0-10V LED Power Supply Installation guide

  • Hello! I've reviewed the installation instructions for the QZ-S LED power supply. This document covers mounting procedures, including vertical and horizontal options, spacing requirements for multiple units, and wiring diagrams for both Phase Dimming and 0-10V Dimming. I'm ready to answer your questions about the QZ-S device.
  • What type of screws are needed for mounting?
    Where should the QZ-S be mounted?
    How much space is needed between multiple power supplies?
INSTALLATION LED POWER SUPPLY - QZ-S
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-28-23
4 1 3
24
3 421
QZ-S Components
Driver Compartment Primary Compartment Secondary Compartment Mounting Tab Slots
TOP VIEW
DRIVER COMPARTMENT
INSTALLATION LED POWER SUPPLY - QZ-S
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-28-23
Required Hardware
Mounting
• #4 Flat head screw
(not included)
The QZ-S must be mounted into a stud for sufficient support, using the slots of each mounting tab
2
SIDE SLOT
The QZ-S can be mounted either vertically or horizontally, utilizing the supplied screws and the mounting tabs on the
bottom of the enclosure
1
.21
"
.625"
INSTALLATION LED POWER SUPPLY - QZ-S
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-28-23
When installing multiple QZ-S power supplies, seperate the enclosures by 3” of space from edge to edge. This prevents the
rise of ambient temperature between the power supplies.
3
3.0"
3.0"
3.0"
Horizontal mount illustrated above Vertical mount illustrated above
INSTALLATION LED POWER SUPPLY - QZ-S
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-28-23
Wiring diagram
4
Phase Dimming
0-10v Dimming
Wiring from power supply to light fixture must be two conductor cable
LED
96W
Phase Dimmer
GND HOTNEU
INPUT
N
L
96W
INPUT
L
N
- OUTPUT +
- DIM +
DIMMING
0/1-10V
−+−+
LED
OUTPUT
GND HOTNEU
96W
- DIM +
LED
- OUTPUT +
0-10V Dimmer
INPUT
N
L
DIMMER
INPUT
L
N
96W
DIMMING
0/1-10V
−+−+
LED
OUTPUT
INSTALLATION LED POWER SUPPLY - QZ-S
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-03-28-23
QZ-S 96W
TOP VIEW
13"
1.18"
SIDE VIEW
0.88"
13"
/