Andersen E-Series Gliding Patio Doors Service Instructions

Andersen
Brand
Andersen
Model
E-Series Gliding Patio Doors
Type
Service Instructions
9069167 BA Revised 09/24/13
Tools Needed
∙Safety Glasses
∙Phillips Screwdriver
∙Needle Nose Pliers
Roller Replacement
for E-Series Gliding Patio Doors
Use caution when working at elevated heights and around unit openings.
Follow manufacturers’ instructions for ladders and/or scaffolding. Failure
to do so may result in injury or death.
Follow manufacturers’ instructions for hand or power tools. Always
wear safety glasses. Failure to do so may result in injury and/or
product damage.
Parts Included
(1) Roller
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com.
Please leave this guide with building owner.
▶Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.
Roller
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved.
Panel must be supported during entire removal and installation
procedures. Failure to support sash may result in injury and/or
product damage.
Windows and doors can be heavy. Use safe lifting techniques and
a reasonable number of people with enough strength to lift, carry
and install window and door products to avoid injury and/or product
damage.
2
9069167
Unlock and open operating panel.
Operating Panel
Remove visible head track screws and save for reuse.
2
Interior
Head Track
Head Track Screw
Drill/Driver
Operating Panel
3
Interior
4
Interior
Close and lock operating panel. Remove remaining head track screws and save for reuse.
Head Track
Head Track Screw
Drill Driver
Unlock and open operating panel half-way.
1
Interior
Operating Panel
5
Interior
Tip top of operating panel and head track panel stop inward from frame.
Lift head track panel stop from top of panel and save for reuse.
6
Interior
Head Track Panel Stop
Operating Panel
Head track rests on
top of operating panel.
3
9069167
Lift operating panel out of frame. Place panel
on a at surface with interior side facing up.
Operating Panel
Remove roller screws from bottom of door panel and save for reuse.
Remove rollers from panel using a needle nose pliers and dispose of
properly.
9
Interior
Needle Nose Pliers Roller
Insert new rollers into rout pocket with adjustment screw facing interior.
10
Interior
Route Pocket
Adjustment Screw
Roller
Fasten roller using saved screws.
11
Interior
Drill/Driver
Roller
Roller Screws
7
Interior
Center operating panel into frame with rollers on sill track. Tip top of
operating panel slightly inward.
12
Interior
Operating Panel
8
Interior
Drill/Driver
Roller
Roller Screws
4
9069167
17
Interior Operating Panel
Place head track/panel stop on top of operating panel with panel stop
facing interior.
13
Interior
Close and lock operating panel.
Tip top of operating panel back into frame.
14
Interior
Head Track Panel
Stop
Operating Panel
Head Track
Head Track
Screw
Drill Driver
Fasten head track with saved screws on
stationary panel side.
16
Interior
Unlock and open operating panel.
Fasten head track with remaining saved
screws on operating panel side.
18
Interior
Head Track
Head Track Screw
Drill/Driver
Close and lock operating panel. Check for
correct lock operation.
15
Interior Operating Panel
19
Interior
Operating Panel
▶Roller replacement is completed.
Head Track Panel Stop
Head Track
Panel Stop
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Andersen E-Series Gliding Patio Doors Service Instructions

Andersen
Brand
Andersen
Model
E-Series Gliding Patio Doors
Type
Service Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents