Workrite Ergonomics Rise Quiet 4-Leg Electric Installation guide

Brand
Workrite Ergonomics
Model
Rise Quiet 4-Leg Electric
Type
Installation guide
BoxA
BoxB
Assembly & Installation Instructions:
Rise Quiet 4-Leg Electric Workcenter
RISE-4E-3648-6696-X
Required & Sold Separately
Worksurface
1 of 2: 4-Leg Frameset, Components & Hardware
2 of 2: 4-Leg Frameset, Components & Hardware
Hardware Kit
Collision Detection System (CDS) Kit
X
Round Bumpers
Qty: 24
X
Round Bumpers
Qty: 2
Q
" P-Clips
Qty: 12
R
" P-Clips
Qty: 6
S
#6 × ⅝" Phillips Flat Head
Wood Screw
Qty: 12
S
#6 × ⅝" Phillips Flat
Head Wood Screw
Qty: 6
O
#8 × ½" Self Tapping
Phillips Head Screws
Qty: 2
P
#8 × ¾" Phillips Pan
Head Wood Screw
Qty: 1
Y
Square Bumpers
Qty: 4
U -18 × " Flat Head
Socket Cap Screws
Qty: 32
W#10 × 2½" Phillips Pan
Head Wood Screws
Qty: 24
L
16 mm Steel Washers
Qty: 20
B Feet
Qty: 2
B Feet
Qty: 2
C Framesets
Qty: 1
C Framesets
Qty: 1
E Switch
Qty: 1
D Cross Bars
Qty: 1
D Cross Bars
Qty: 1
I Leg Cable
Qty: 2
I Leg Cable
Qty: 1
H Power Supply Bracket
Qty: 1
H Power Supply Bracket
Qty: 1
J Power Cable
Qty: 1
J Power Cable
Qty: 1
A Legs
Qty: 2
A Legs
Qty: 2
K 20 mm Foam Washers
Qty: 40
N Collision Detection
Sensor
Qty: 1
Z Zip Ties
Qty: 4
G Power Supply
Qty: 1
G Power Supply
Qty: 1
F 3.5 mm × 16 mm Phillips
Head Wood Screw
Qty: 2
B Round Plugs
Qty: 12
B
B Round Plugs
Qty: 24
B
A "Y" Cable
Qty: 1
A
T -18 × " Button Head
Socket Cap Screws
Qty: 8
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 12
0.656"0.198"
5/8"
0.3125"
82°
WARNING: Maximum load of frameset is 520 lb. (236 kg.). Maximum load includes the weight of the table top itself,
any equipment placed upon it, and any equipment suspended or hanging under it. Loading should be evenly distributed over table surfaces.
Rise 4-Leg
V = 120 VAC, 60 Hz
6.4 A maximum with standard two power supplies
Duty cycle: 1 minute on/ 9 minutes o.
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this Rise Quiet Frameset.
DANGER: To reduce the risk of electric shock, always unplug this Rise Quiet Frameset from the electrical outlet before cleaning.
CAUTION-RISK OF ELECTRIC SHOCK. This unit has two power cords. Unplug both cords before moving or servicing this furnishing.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlets before putting on or taking o parts, moving or servicing.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into
water. Return the furnishing to a service center for examination and repair.
5. Keep all cords away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plugs from outlet.
9. This Rise Quiet Frameset is intended to support a maximum frameset capacity of 520 lb. (236 kg.).
SERVICING OF DOUBLE-INSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-
insulated product, nor is a means for grounding to be added to the product. Servicing a double-insulated product requires extreme care and
knowledge of the system, and is to be done by a qualified service personnel. Replacement parts for a double-insulated product must be identical
to the parts they replace. A double-insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”. The symbol
(square within a square) is also able to be marked on the product.
FOR COMMERCIAL USE ONLY
SAVE THESE INSTRUCTIONS
Verify that you have all the hardware and tools needed for the assembly
Check your cartons against the list above to verify that you have all the parts needed.
You will also need the following tools:
Drill/driver with #2 Phillips head bit
" Allen bit for drill/driver
or " Allan Wrench (Z) provided
If you do not have a Workrite pre-drilled worksurface, you will also need:
⅛" drill bit
Tape measure
2 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
✓
An electric Drill/Driver is
recommended over hand
tools for this installation.
Layout Components in Assembly Area
Assemble near final installation location. Once the Workcenter is built it requires at least two people to li and
move into place. You'll need a large and clean area to assemble. Check your packaged contents against the parts
list on page 1 to verify that you have all the parts needed.
If you have a Workrite Pre-Drilled Worksurface, it may be easiest to assemble on the bottom of the worksurface,
using the pre-drilled holes as a guide.
Place Legs (A), Feet (B), Framesets (C) and Cross Bars (D) on the floor or bottom of your worksurface.
Set the Switch (E), Collision Detection Sensor (N) packaged separately, and Power components (G,H,I & J) within
easy reach.
Carefully unpack and arrange all hardware.
Note! You will have many pieces in common and some VERY SIMILAR parts in the Silence Kit, Collision Detection
Kit,Cable Management and Hardware Kit. Use caution!
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 3 of 12
1
C
C
A
AA
A
D
B
B
D
B
I
I
I
B
J
J
H
H
G
G
4-Leg Frameset Hardware CDSSwitch
K
L
EN
O
P
R
S
F
Q
S
T
W
X
X
Y
Z
U
BB
AA
Box1
Box2
1 of 2: 4-Leg Frameset
2 of 2: 4-Leg Frameset
Attach Bumpers to Underside of Framesets
Apply the twenty Round Bumpers (X) at mount location on the Frameset as shown.
Note: Round Bumper (X)locations are approximately one inch to the side of all frame mount hole locations.
Apply the four Square Bumper (Y) at the Joining Bracket location just to the side of the center mount hole.
Attach Framesets to Legs
Flip the Frameset over so the Bumpers rest on
the Worksurface. Keep frame oriented as show
with "knee saver" area towards users.
Loosen the Joining Bracket on the Frameset at
locations shown with the Allen head bit or wrench.
NOTE! Loosen frameset but do not disassemble!
Move the internal Joining Brackets
out of the way to allow attachment
of legs. Keep frameset loose.
With frameset Joining Bracket still
loose, attached the four legs to the
frameset using sixteen -18 × "
Flat Head Socket Cap Screws (T).
4 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
Make sure Frameset is oriented with
"knee saver" area towards user
X
X
X
X
X
Y
Y
Y
Y
To avoid stripping the threads, always insert and make
the first few turns of the screw BY HAND with the provided
Allen wrench, ensuring it is in straight.
a
a
b
b
T
T
T
T
2
T -18 × " Flat Head
Socket Cap Screws
Hardware at actual size
X
Round Bumpers
Hardware at actual size
Y
Square Bumpers
Hardware at actual size
A
A
A
A
3
a
a
b
b
b
cc
c
Joining Bracket
Joining Bracket
Joining Bracket
Round Bumper (X) locations
about 1" from mount holes
Joining Bracket
Joining Bracket
Mount hole
Attach Feet to Legs
Attach four Feet (B) To Legs (A) using eight -18 × " Button
Head Socket Cap Screws (T).
Tighten Securely.
Expand Framesets to Correct Length
With Legs & Feet secure but the frameset
Joining Bracket still loose, extend the
Frameset (B) and Cross Bars (C) out towards
the edge of the worksurface.
If you have a Workrite pre-drilled
Worksurface:
Align frameset holes with pre-drilled holes in
the undersides of the worksurface.
Adjust Joining Brackets so center bracket
hole aligns with the center hole location.
Proceed to Step 6.
If you have a non- Workrite top:
Align frameset parallel and centered on the
worksurface.
Position frameset 3.25" from edge of
Worksurface and extend frameset until the
Cross Bars (D) are about 1.5"–2" from the
ends of the top.
Adjust Joining Brackets so center bracket
hole is centered between framesets.
Proceed to Step 7.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 5 of 12
3.25" Min.
3.25" Min.
A
D
D
B
T
4
T -18 × " Button Head
Socket Cap Screw
Hardware at actual size
CAUTION! Be sure to use the correct
hardware for this step!
5
a
a
a
a
a
a
b
b
b
c
c
d
c
c
d
Adjust Joining Brackets so middle hole
aligns with screw location.
Adjust Joining Brackets so
middle hole is centered.
Attach Frameset to Workrite Pre-Drilled Worksurface
If you do not have a Workrite Pre-drilled Worksurface, skip to Step 7.
With Frameset positioned correctly from Step 5, carefully li Frameset assembly to place the Power Supply
Bracket (H) under the Frameset at locations shown.
Carefully li the Frameset to place twenty 20 mm Foam Washers (K) at all frame mount locations UNDER the
frameset as shown. Be sure to keep frameset aligned with pre-drilled holes.
Attach the Frameset assembly with sixteen 16 mm Steel Washers (L), twenty Foam Washers (K) and twenty
×2⅛" Flat Head Phillips Wood Screws (W). NOTE: No 16 mm Steel Washers (L) and only one BOTTOM Foam
Washer (K) are used in the Joining Bracket center frame location.
With frame securely fastened to the worksurface, re-tighten the Joining Brackets loosened in Step 3a.
Proceed to Step 8.
6 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
6
a
b
c
d
L #8 × ¾ Phillips Pan Head
Wood Screw
Hardware at actual size
NOTE
Attaches Side Bars (D) to Worksurface.
V #10 × 2½" Phillips Pan Head Wood Screws
NOTE
Attaches Frameset (C) to Worksurface.
Hardware at actual size
Joining Bracket
location, bottom
Foam Washer (J) only.
K located
between frameset
and worksurface
K located
between frameset
and worksurface
K
b
c
W
C
C
K
Kb
c
W
L
a
H
C
K 20 mm Foam Washers
Hardware at actual size
d
Retighten
H
H
Attach Frameset to Non- Workrite Top
With Frameset positioned correctly from Step 5, use a ⅛" drill bit to drill pilot holes in the twenty frameset
mounting locations shown.
You may wish to mark your drill bit so you do not drill any more than ¾" deep to avoid damaging your
worksurface top. Do not drill all the way through worksurface!
Carefully li the Frameset to place twenty 20 mm Foam Washers (K) at all frame mount locations UNDER the
frameset as shown. Be sure to keep frameset aligned with pre-drilled holes.
Attach the Frameset assembly with sixteen 16 mm Steel Washers (L), twenty Foam Washers (K) and twenty
×2⅛" Flat Head Phillips Wood Screws (W). NOTE: No 16 mm Steel Washers (L) and only one BOTTOM Foam
Washer (K) are used in the Joining Bracket center frame location.
With frame securely fastened to the worksurface, re-tighten the Joining Brackets loosened in Step 3a.
Proceed to Step 8.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 7 of 12
1.5" Minimum
1" Minimum
12
3
5
4
6
78
9
10
11
12 13 14
15
17
16
18
19 20
>¾"
12
3
5
>¾"
Joining Bracket
location, bottom Foam
Washer (K) only.
K located
between frameset
and worksurface
K located
between frameset
and worksurface
K
b
c
W
C
C
K
Kb
c
W
La
H
C
d
Retighten
7
a
b
Mark drill bit so you do not
drill through your top
a
a
c
d
Mark
H
H
Install Switch
Install your Switch (E) using two 3.5mm×16 mm
Pan Head Screws (F).
If you have a Workrite pre-drilled
Worksurface:
Locate the pre-drilled holes near the front edge
of the Worksurface and attach.
If you have a non-Workrite top:
Align the switch with the front edge of the top,
use a ⅛" drill bit to drill pilot holes using the
Switch holes as a guide and attach.
Do not drill all the way through worksurface!
Attach Anti-Collision Detection Sensor to Frameset
and Worksurface
Attach the two Round Bumpers (X) to the contact surface of the
Collision Detection Sensor (N). Place the bumpers down, contacting
the worksurface and position on Frameset (C) as shown.
Attach Collision Detection Sensor (N) to worksurface with one #8 × ¾" Phillips Head Wood Screw (P).
Attach the Collision Detection Sensor (N) to the Frameset (C) using the two #8×¾" Self Tapping Screws (O). You
will need to apply pressure with the screw in place to make the "bit" of the screw drill into the frame then catch
to attach and hold secure.
8 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
9
E
F
O
8
a
C
b
c
Use Self Tapping
Screws (O) to drill
into frame
Alternate location
Alternate location
O #8 × ½" Self Tapping
Phillips Head Screw
Hardware at actual size
P
#8 × ¾" Phillips Pan
Head Wood Screw
Hardware at actual size
C
C
N
X
a
Improper installation of the Collision
Detection Sensor may result in false
collision incidents. Please follow
instructions closely.
b
P
CDS mount location
N
N
Route and Connect Cables
Connect Switch (E) to closest Leg (A).
Connect the Y Cable (AA) into the Leg closest to the Collision Detection Sensor (N).
Connect Collision Detection Sensor (N) to the closest Leg (A) via the Y Cable (AA).
Connect both Legs with Leg Cable (I), one of the two will plug in via the Y Cable (AA) .
Slide in both Power Supplies (G) into the Power Supply Brackets (H).
Connect both Power Supplies (G) to the closest Leg.
Plug Power Cord (J) into the Power Supply (G).
Zip Ties (Z) can be used where needed to bundle cables.
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 9 of 12
10
To Power
Plug in
To Leg (A)
G
J
J
J
G
G
f
g
I
b
AA
c
A
A
A
d
d
d
E
A
I
E
I
H
H
I
J
Z
I
N
a
a
b
d
e
e
f
g
c
d
fG
Attach Cables to Worksurface With P-Clips
Attach the P-Clips (Q & R) with #6 × ⅝" Phillips Head Wood Screws (S) at convenient locations to keep cables
up and out of the way being sure to rout the cables through the Clips prior to attaching to the underside of the
worksurface.
Note: the larger " P-Clips (Q) are used on the Leg Cables (I) and the smaller " P-Clips (R) are used on all
other cables.
Insert Round Plugs
Insert the Round Plugs
(BB) into corresponding
Frameset holes as shown.
10 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
11
12
BB
I
Q
R
S
Initialize Legs
Aer all components are connected, and the power cord has been plugged
in, the Legs need to be initialized.
Press and hold the UP and DOWN arrows on the Switch for at least 8 seconds.
Release both buttons and immediately press the DOWN arrow. The display will show three dashes and a home
icon in the lower le of the display as the worksurface moves to its lowest position.
Once the worksurface stops moving, release the button and the three dashes will be replaced with the height
reading. The Legs are initialized and the Workcenter is ready to use.
Put Workcenter Upright and Plug in Power Cord
Turn the workcenter over into an upright position. Use at least two people to flip
over and position the workcenter.
Plug both Power Cords (J) into power outlets.
Adjust Leveling Guides
If necessary, adjust leveling guides on table feet to level the worksurface.
Cleaning Instructions
To clean the legs, apply cleaner to a so cloth.
Suggested cleaners: Windex or Formula 409.
Do not use solvents and do not saturate or spray cleaners directly onto workcenter base.
Parts & Accessories
Visit http://workriteergo.com/documentation/other/workrite_ergonomics_pricing_specification_guide.pdf for
replacement parts.
Download the Rise Programmable Control User Guide
To get the full ergonomic benefit of this Workcenter, download the Rise Programmable User Guide. It contains
detailed information on set up and programming of your Rise Workcenter.
http://workriteergo.com/support/rise-control
Workrite Ergonomics | 800.959.9675 www.workriteergo.com 11 of 12
13
14
a
a
b
b
c
b
15
J
You must complete this
initialization step or your
workcenter will NOT
function properly!
✓
✓
16
a
Flip Workcenter on
its FRONT or BACK so
you do not damage
the switch.
12 of 12 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
#1500360 - Rev A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Workrite Ergonomics Rise Quiet 4-Leg Electric Installation guide

Brand
Workrite Ergonomics
Model
Rise Quiet 4-Leg Electric
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents