Workrite Sierra HX 3-Leg Installation guide

Brand: Workrite

Model: Sierra HX 3-Leg

Type: Installation guide

Workrite Sierra HX 3-Leg is a height-adjustable workstation that offers ergonomic benefits and customizable features. It boasts a sturdy construction with three legs and a spacious worksurface (sold separately) that can accommodate various tasks and equipment. With its electric motor and control box, you can effortlessly adjust the height of the table to suit your preferred working position, promoting comfort and productivity.

Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 1 of 11

I 4 mm Allen Wrench

Qty: 1 R Leg Cable, 1 Meter

Qty: 2

U Style or Flat

Foot Kit

Qty: 1

M #12 x 2" Flat Head Screw

Qty: 2

O Cable Spool

Qty: 3

B Rear Bracket

Qty:3

C Connector

Bracket

Qty: 2

A Leg

Qty: 3

D Short Bracket

Qty: 3

N Control Box

Qty: 1

K Corner Glide

Qty: 1

L Foot Glides

Qty: 4

E Le End Bracket

Qty: 1

F Right End Bracket

Qty: 1

G Corner End Bracket

Qty: 1

J #12 × ¾" Pan Head

Screw

Qty: 53

S Leg Cable, 2 Meters

Qty: 1

P ⁄" Cable Loops

Qty: 15

H #M6 × 14 mm Flat Head

Cap Screw

Qty: 32

Q #8 × ⅝" Pan Head Screw

Qty: 17

T Power cord

Qty: 1

Glide Adjuster Center Foot

Qty: 4

Worksurface Required, Sold Separately:

Equal Corners Width Left Width Right Depth

24" Feet 58–72" 58–72" 23–24"

30" Feet 58–72" 58–72" 29–30"

Left Offset Corners Width Left Width Right Depth

24" Feet 58–72" 46–60" 23–24"

30" Feet 58–72" 46–60" 29–30"

Right Offset Corners Width Left Width Right Depth

24" Feet 46–60" 58–72" 23–24"

30" Feet 46–60" 58–72" 29–30"

Assembly & Installation Instructions:

Sierra HX 3-Leg Work Center

SEHX5472-4272EOC-XXX-XX-X

Parts Included

V Standard, Bluetooth, or

Programmable Switch

Qty: 1

0.4126"

#3 Drive

0.134"3/4"

0.216"

#12 Screw Size

Tools Required:

Cordless Drill #2 Phillips Bit

Screwdriver or

Driver/Drill

⅛" pilot drill bit

pencil

3⁄32" pilot drill bit

#3 Phillips Bit

Screwdriver or

Driver/Drill

2 of 11 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com

SAVE THESE INSTRUCTIONS

WARNING: Maximum equipment loading of table assembly in addition to specied top is as follows:

 Maximum Top Weight: 128 lb (58.2 kg)

 Maximum Equipment Load: 300 lb (136.3 kg)

Loading should be evenly distributed over table surfaces.

V = 120 VAC, 60 Hz / 4 A maximum

FLAMMABILITY: All worksurfaces used must meet UL 962 ammability requirements

 Flame Spread Rating maximum 200

 Smoke Developed Index maximum 450

WORKSURFACE MATERIAL: This frameset is designed to accommodate worksurfaces made from Industrial Particle Board with nominal thickness

of 1.125". If the worksurface is not appropriate or not mounted correctly to the table, it could cause the complete table to be unstable, it may collapse,

and for an adjustable table, the electrical components may fail.

Intended for indoor use only.

For commercial use only.

IMPORTANT SAFETY INSTRUCTIONS:

When using an electrical furnishing, basic precautions should always be followed, including the following:

Read all instructions before using this Sierra HX Work Center.

DANGER: To reduce the risk of electric shock, always unplug this Sierra HX Work Center from the electrical outlet before cleaning or servicing.

WARNING: To reduce the risk of burns, re, electric shock, or injury to persons:

1. Unplug from outlet before putting on or taking off parts.

2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.

3. Use this Sierra HX Work Center only for its intended use as described in these instructions, do not use attachments not

recommended by the manufacturer.

4. Never operate this Sierra HX Work Center if it has a damaged cord or plug, is not working properly, has been dropped or

damaged, or dropped into water. Return the furnishing to a service center for examination and repair.

5. Keep the cord away from heated surfaces.

6. Do not operate outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, remove plug from outlet.

9. Do not exceed maximum load recommendations.

Polarized Plug Instructions (Only applicable to products having a polarized plug power cord):

Some products include a polarized plug—see Figure A (One A/C plug blade wider than the other)—to reduce the risk of

electrical shock. A polarized plug only ts a polarized power outlet one way. If the polarized plug does not t properly into the

electrical outlet turn the power plug over to see if it then ts properly and fully into the outlet. If the plug does still does not t

the outlet, contact a certied electrician to install the correct matching polarized electrical outlet.

Caution: Never modify the power cord plug in any way

Double-Insulated Products Instructions:

Some products are double-insulated. No means of grounding is required or provided on a double-insulated product; nor is a

means for grounding to be added to the product. The plug in a double insulated system is shown in Figure A. Double-insulated

products are indicated with markings of “double-insulated” or the “double box symbol” or both.

Grounding Instructions (For grounded electric products only):

Products with grounded power cords are for use on a nominal 120 V circuit and has a grounded plug as shown in Figure B

Make sure the product is connected to an electrical outlet having the same conguration as the plug shown in Figure C.

Caution: Never modify, remove, or use adaptors that eliminate the ground connections from the grounded power cord

A/C Power:

Products sold in North America and other regions are 120 V A/C as marked on the power supply/control box of the furnishing

and are to be used on a normal 120 V A/C circuit. Always follow the instructions above for power connection using grounded or

double insulated power cords as supplied.

• Only use power cord(s) supplied with your electric product

• Never modify, alter, use an adaptor, or change the electrical system of this product in any way.

Warning: Doing so may cause risk of electrical shock or re

Illustration Disclaimer—Power Plug and Receptacle Images:

In some cases, the images in this instruction may not match the power cord supplied with your electrical furnishing based on your region.

Plug type, blade size, and shape may change.

Grounding Pin

Figure B

Grounded Outlet

Figure C

Polarized Plug

Figure A

Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 3 of 11

1 Assemble Rear Brackets Set

Assemble Rear Brackets (B) to Connector Bracket (C) using

#M6 × 14 mm Flat Head Cap Screws (H).

Use this guide to determine the correct holes for mounting

based on the width of your work center.

Tighten securely.

Note: Workrite Brackets can be

sized in 3" increments for any

non-Workrite top. 61"

55"

49"

43"

Note: Brackets can be sized in 6"

increments for any non-Workrite top.

Connected Side,

Right Configuration Connected Side,

Le Configuration

When shown upside down, right will be on your le and vice-versa. Your frameset may dier.

To avoid stripping the threads, always

insert and make the first few turns

of the screw BY HAND with an Allen

wrench (I), ensuring it is in straight.

52" Work Centers

58" Work Centers

64" Work Centers

70" Work Centers

H #M6 × 14 mm Flat Head

Cap Screw

Hardware at actual size

Caution!

Only use the #M6 × 14 mm Flat Head

Cap Screw (H) for assembly.

4 of 11 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com

2 Assemble Rear Floating Bracket—Shorter or Equal Side

Assemble Rear Brackets (B) to Connector Bracket (C )

with two #M6 × 14mm Flat Head Cap Screws (H).

Use this guide to determine the correct holes for

mounting based on the width of your worksurface.

Tighten securely.

43.75"

40"

37.75"

34.75"

21"

43.75"

40"

37.75"

34.75"

21"

Floating Side,

Right Configuration

Floating Side,

Le Configuration

When shown upside down, right will be on your le and vice-versa. Your frameset may dier.

Use with 70"× 23",

70"×29" or

64"×23" widths

Use with 64"× 29"

or 58"×23" widths

Use with 58"×29" widths

Note: Brackets can be sized

in 3" increments for any

non-Workrite top.

Use with 42"– 48" widths

H #M6 × 14 mm Flat Head

Cap Screw

Hardware at actual size

Caution!

Only use the #M6 × 14 mm Flat Head

Cap Screw (H) for assembly.

To avoid stripping the threads, always

insert and make the first few turns

of the screw BY HAND with an Allen

wrench (I), ensuring it is in straight.

Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 5 of 11

3 Attach Short & Medium Brackets

3.1 Attach Short Brackets (D) using #M6 × 14 mm Flat Head Cap

Screws (H) to all three legs.

3.2 Attach Right End Bracket (F) to sides of the Right Leg (A) using #M6 × 14 mm Flat Head Cap Screws (I). Attach Le

End Bracket (F) to sides of the Le Leg (A) using #M6 × 14 mm Flat Head Cap Screws (H).

3.3 Attach Corner End Bracket (H) to the Center Leg (A) using #M6 × 14 mm Flat Head Cap Screws (I).

3.4 Attach both the Connected Rear Bracket (B & C assembled) and Floating Rear Bracket (B or B & C assembled)

using #M6 × 14 mm Flat Head Cap Screws (H).

3.5 Make sure the Connected Rear Bracket is on the longer of the two sides.

Tighten securely.

Note: The Right End Bracket (F) will be

on your le and vice versa when the

assembly is upside down.

Note: Le configurations will assemble as

a mirror image of these instructions.

Le Leg

Center Leg

Right Leg

Three piece

Connected Rear Bracket

B & C assembled Floating Rear Bracket

B or B & C

Right End Bracket Le End Bracket

Right configuration

44" & 48" configurations have a single Floating

Rear Bracket B on the shorter side.

3.1

3.2

3.3

3.4

3.3

3.1

Le configuration

44" & 48" configurations

H #M6 × 14 mm Flat Head

Cap Screw

Hardware at actual size

Caution!

Only use the #M6 × 14 mm Flat Head

Cap Screw (H) for assembly.

To avoid stripping the threads, always

insert and make the first few turns

of the screw BY HAND with an Allen

wrench (I), ensuring it is in straight.

6 of 11 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com

5.4 Using the " Drill Bit, pilot drill the remaining

mounting holes in all bracket locations as shown

Be careful to not drill through the worksurface!

5.5 Install the remaining #12 × ¾" Pan Head

Screws to all the remaining bracket mounting

locations and tighten securely.

Do Not Overtighten!

4 Attach Feet & Install Foot Glides

4.1 Install Corner Glide (K) to bottom of center leg (A).

4.2 Install two (2) outside feet (U) using eight

#M6 × 14 mm Flat Head Screws(I) included with this

frame set.

4.3 Attach the remaining Foot Glides (L) to bottom of

the feet supplied in your Foot Kit.

5 Attach Base to Worksurface

5.1 Position the base assembly onto the top. Place the right and le leg in 2" from end

brackets to the outside edges of the top. Next center the feet front to back over the

depth of the top. Make sure the stretchers are parallel to the rear edge before drilling.

5.2 Using the ⅛" drill bit, pilot drill the six end bracket locations as shown.

Be careful to not drill through the worksurface!

5.3 Install six (6) #12 × ¾" Pan Head Screws (J) using

a #3 Phillips Screw bit in the corner locations and

tighten securely. Do Not Overtighten!

5.4

5.5

2.875"

>¾"

Flat Foot shown

5.3

5.1

5.2

5.1 5.1

5.2

5.3

J #12 × ¾" Pan Head Screw

Hardware at actual size

Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 7 of 11

7 Loop Power Cord & Center Leg Cable through Strain Relief on Control Box

7.1 Loop the Power Cord (T) through the

strain relief channel on the bottom of the

Control Box (N) as shown. Leave 8" of

slack to route cord

7.2 Thread the 1 meter Leg Cable (R) from

the center leg through the cable channel

on the bottom of the Control Box as

shown. Leave 8" of slack to route cable.

7.3 Plug Power Cord (T) into power outlet AC

on the Control Box (N).

7.4 Plug Leg Cable (R) into port “3” on the

Control Box.

7.5 Lay the Control Box down in installation

location with cables in place.

6 Attach Switch (Packaged Separately)

6.1 Using the dimensions shown place the Switch (V)

on the desktop

6.2 Using a Drill and a /" drill bit, drill the two switch

mounting holes as shown.

6.3 Attach the Switch (V) as shown with two

(2) #8 x ⅝" Pan Head Screws (Q)

Note: The Switch (V) can be located on the Right or Le

side of the table as required.

This may require relocation of the control box to allow

the switch cable to reach the Control Box (N).

0.75”

17.90mm

2.00”

50.80mm

Switch Housing

Q #8 × ⅝" Pan Head

Screw

7.3

7.4

7.2

7.1

bottom

Hardware at actual size

6.1

6.3

1/ 1/ 

Programmable Switch

Standard or Bluetooth Switch

Note: use the screws provided with Standard & BT-Proswitch

to mount the switch using the diagram above.

8 of 11 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com

Attach Control Box & Cable Spools to Worksurface

8.1 Place Control Box (N) in position and use a pencil to mark pilot hole placement. Control Box should be

placed towards rear center of worksurface as shown. Remove Control Box and drill pilot holes where marked.

Do not drill all the way through tabletop!

8.2 With Control Box (N) positioned over pilot holes, attach with two #12 × 2" Flat Head Screws (M).

8.3 Attach Cable Spool (O) with the #12 × ¾" Pan Head Screw (J) to underside of worksurface. If you do not have a

Workrite worksurface, mount Cable Spools (O) in a convenient location between legs and control box.

8.4 Lay out Leg Cables (R & S) to be sure they all reach the Control Box.

8.1

8.2

8.3

8.4

J #12 × ¾" Pan Head Screw

Hardware at actual size

#12 × 2" Flat Head Screw

Hardware at actual size

Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 9 of 11

Attach Cable Loops & Route Cables

9.1 Route cables as shown, using Cable Spools (P) to take up any slack. Use the 2 Meter Leg Cable (S) for the Leg

furthest from Control Box (N).

9.2 Attach Cable Loops (P) to underside of worksurface using #8 × ⅝" Pan Head Screw (Q) making sure to wrap the

Cable Loop around the cable prior to attaching. Attach cable loops in convenient locations between legs or

switch and the control box.

Note the additional P-Loop and Cable Spool locations that may provide better attachment and routing options

for your specific configuration.

9.1

9.2

9.1

Q #8 × ⅝" Pan Head

Screw

Hardware at actual size

Switch Cable

9.2

10 of 11 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com

Connect Leg Cables, Control Cable and Power Cord to Control Box

10.1 Connect the Right Leg Cable (R) to the port on the Right Leg (A) and port “1”on the Control Box (N). Connect the

Center Leg Cable (R) to the port on the Center Leg (A).

10.2 Insert the Switch Cable into port “A1” on the Control Box (O).

10.3 Connect 2 meter Leg Cable (S) to the port on the Le Leg (A) then to port “2” on the Control Box (O)

Switch Cable into

Switch Port “A1" S

10.3

Installed in

Step 9 Installed in

Step 9

10.2

10.3

10.1

Workrite Ergonomics | (800) 959–9675 www.workriteergo.com 11 of 11

#1500352 Rev H

Put Work Center Upright & Connect Power Cord to the Power Supply

11.1 Turn the work center over into an upright position.

Note: Always use at least two people to flip and move work centers. Caution! Heavy!

11.2 Plug the Power Cord (U) into the power outlet.

Adjust Feet Glides

If necessary, adjust Foot Glides (M) on the feet to level the worksurface. Unscrew to increase height, screw in to

decrease height.

For Center Foot, use "Glide Adjuster" as needed (comes in ¼" to ½" spacers).

✓ Cleaning instructions

To clean the Sierra legs, apply cleaner to a so cloth.

Suggested cleaners: Windex or Formula 409.

Do not use solvents and do not saturate or spray cleaners directly to work center base.

You must complete this

initialization step or your

work center will NOT

function properly.

Hold down the down

arrow until work center

moves slightly upwards!

✓ Replacement Parts

Visit http://workriteergo.com/documentation/other/workrite_ergonomics_pricing_specification_guide.pdf for

replacement parts.

Initialize Legs

Aer all legs and the switch are connected, and the power cord has been plugged in, hold the down arrow on

the switch until the legs make a short motion down and then back up. This initializes and synchronizes the work

center legs.

11.1

11.2

Workrite Sierra HX 3-Leg Installation guide

Workrite Sierra HX 3-Leg Installation guide

Workrite Sierra HX 3-Leg Installation guide

Related papers

Other documents