ROSE DISPLAYS ANOSCREEN WITH BASE RAIL User manual

Brand: ROSE DISPLAYS

Model: ANOSCREEN WITH BASE RAIL

Type: User manual

This manual is also suitable for

AnoScreen

ROSE DISPLAYS ANOSCREEN WITH BASE RAIL

The AnoScreen is a versatile display system that can be used to create a variety of different configurations, including 2, 3, or 4 panels. It is easy to assemble and disassemble, making it a great option for portable displays. The AnoScreen is also durable and weather-resistant, making it suitable for both indoor and outdoor use.

Here are some of the key features of the AnoScreen:

Easy to assemble and disassemble - The AnoScreen can be assembled and disassembled in minutes without any tools. This makes it a great option for portable displays or for displays that need to be set up and taken down frequently.

ROSE DISPLAYS ANOSCREEN WITH BASE RAIL

Here are some of the key features of the AnoScreen:

Easy to assemble and disassemble - The AnoScreen can be assembled and disassembled in minutes without any tools. This makes it a great option for portable displays or for displays that need to be set up and taken down frequently.

The AnoScreen™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products.

Part#02INSAnoScreenBaseRail

Incept-8.15.02

35 Congress Street, Salem, MA 01970

Tel# 1-800-631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Instruction Sheet

Step 1

Insert corner brackets into ends of

bottom base rails, using thumb, as

shown in illustration. 2 brackets per

end of each rail. Fig. 1

Detail Fig. 1a- Corner bracket tension

tabs face toward outside of frame.

Step 2

Lay out parts as they will be configured

on the floor. (2, 3 or 4 panels)

Step 3

Assemble the vertical rail assemblies

onto the upward facing corner brackets

already inserted into the bottom base

rails. All 4 brackets can go into the

vertical rails at one time, or you can do

one side at a time.

Note: Make sure grommets are on the

top end of the vertical panels. Use the

two vertical rails without flex spine

connectors on the outside edges of the

outermost panels.

AnoScreen™

Instructions For Assembly

1 1a

Parts

(continued on other side)

Base Rails Corner Brackets Split Rails

Vertical Rails

with Flex Spine

Ano rails

2 Panel

3 Panel

4 Panel

The AnoScreen™ is a registered trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products.

Part#02INSAnoScreenBaseRail

Incept-8.15.02

Instruction Sheet

AnoScreen™

Instructions For Assembly

Parts

(continued on other side)

1 1a

2 2a

2 Panel

3 Panel

4 Panel

Step 1

Insert corner brackets into ends of

bottom rails, using thumb, as shown

in illustration. 2 brackets per end of

each rail. Fig. 1

Detail Fig. 1a- Corner bracket tension

tabs face toward outside of frame.

Step 2

Snap base Ano rail sections into the

Vario base section.

Start at one end and work the Vario

base onto the Ano rail.

Step 3

Lay out parts as they will be configured

on the floor. (2, 3 or 4 panels)

Vario Base Corner Brackets Split Rails

Vertical Rails

with Flex SpineAno rails

The AnoScreen™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products.

Part#02INSAnoScreenBaseRail

Incept-8.15.02

35 Congress Street, Salem, MA 01970

Tel# 1-800-631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Instruction Sheet (side 2)

Instructions For Assembly Continued

Step 4

Insert corner brackets into ends of split

rails, using thumb, as shown in illustra-

tion. 1bracket per end of each split rail.

Step 5

Assemble split rails onto top ends of

vertical rails, one inside and one

outside of each panel of the

AnoScreen.

Step 6

Insert and change signs through top

of each panel.

AnoScreen™

4 5

The AnoScreen™ is a registered trademark of Rose Displays, Ltd. Neither

the manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products.

Part#02INSAnoScreenBaseRail

Incept-8.15.02

Instruction Sheet (side 2)

Instructions For Assembly Continued

AnoScreen™

5 6

Vario Base

Corner brackets

& Split Rails

Step 4

Assemble the vertical rail assemblies onto

the upward facing corner brackets already

inserted into the bottom rails. All 4

brackets can go into the vertical rails at

one time, or you cando one side at a

time.

Note: Make sure grommets are on the

top end of the vertical panels. Use the

two vertical rails without flex spine

connectors on the outside edges of the

outermost panels.

Step 5

Insert corner brackets into ends of split

rails, using thumb, as shown in illustra-

tion. 1bracket per end of each split rail.

Step 6

Assemble split rails onto top ends of

vertical rails, one inside and one

outside of each panel of the

AnoScreen.

Step 7

Insert and change signs through top

of each panel.

ROSE DISPLAYS ANOSCREEN WITH BASE RAIL User manual

Brand: ROSE DISPLAYS

Model: ANOSCREEN WITH BASE RAIL

Type: User manual

This manual is also suitable for

AnoScreen

ROSE DISPLAYS ANOSCREEN WITH BASE RAIL

Here are some of the key features of the AnoScreen:

Easy to assemble and disassemble - The AnoScreen can be assembled and disassembled in minutes without any tools. This makes it a great option for portable displays or for displays that need to be set up and taken down frequently.

Download PDF

report

ROSE DISPLAYS ANOSCREEN WITH BASE RAIL User manual

This manual is also suitable for

ROSE DISPLAYS ANOSCREEN WITH BASE RAIL User manual

Related papers

Other documents