ROSE DISPLAYS ECONOSTAND WITH ANOFRAME User manual

  • Hello! I've reviewed the instruction sheet for the EconoStand and AnoFrame, focusing on the assembly process. The manual details how to build the frame using corner brackets and split rails, and also how to set up the display stand with its base, pole and holder brackets. I'm ready to assist with any questions you might have about this product.
  • What parts are included for the frame assembly?
    How do I assemble the frame?
    How do I assemble the base of the stand?
    How do I attach the rails to the stand?
Parts
35 Congress Street, Salem, MA 01970
Tel# 1- 800 631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Step 1
Assemble frame except for split rails.
Insert corner brackets into AnoFrame
sides. Fig. 1
Note: Assembly brackets
tension tabs face towards outside
of frames. Split rail side is made
up of 2 separate pieces.
Step 2
Insert corner brackets into split
rails and into rail opposite split
rail as shown in Fig. 2 . Assemble
frame following diagram steps
1 thru 3, sliding sides together
in the order shown.
Instructions for Assembly
Incept-9.10.02
The AnoFrame and EconoStand are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSEcono/AnoFrame
2
1
split rails
solid rail
Corner
brackets
1
2
AnoFrame rails
12AF100
AnoFrame
split rails
3
solid rail
solid rail
* Assemble frame
except for split rails.
Page 1
Instruction Sheet
EconoStand™ with AnoFrame™
(continued on other page)
Finished look
Parts
Step 3
Assemble bottom holder bracket onto
lower pole section (this is the thicker
section of the pole.
Step 4
Screw pole onto baseplate.
Tighten securly.
Step 5
Place stand upright. Using thumbscrew
at top of pole, attach top holder
bracket onto pole top.
Step 6
Slide top and bottom rails onto
holder brackets.
Step 7
Assemble split rails onto side ends
of solid rails, one inside and one
outside of each side of the AnoFrame.
Fig. 7 & 8
Step 8
Adjust height of stand as necessary.
Instructions for Assembly
Incept-9.10.02
EconoStand
components
The AnoFrame and EconoStand are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSEcono/AnoFrame
Base
Plate
Pole
Top
Holder Bracket
Bottom
Holder Bracket
Top
Thumb
Screw
3 4
56
7 8
Instruction Sheet
EconoStand™ with AnoFrame™
Page 2
Finished look
35 Congress Street, Salem, MA 01970
Tel# 1- 800 631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Parts
Step 1
Assemble frame except for split rails.
Insert corner brackets into AnoFrame
sides. Fig. 1
Note: Assembly brackets
tension tabs face towards outside
of frames. Split rail side is made
up of 2 separate pieces.
Step 2
Insert corner brackets into split
rails and into rail opposite split
rail as shown in Fig. 2 . Assemble
frame following diagram steps
1 thru 3, sliding sides together
in the order shown.
Instructions for Assembly
Incept-9.10.02
The AnoFrame and EconoStand are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSEcono/AnoFrame
2
1
split rails
solid rail
Corner
brackets
1
2
AnoFrame rails
12AF100
AnoFrame
split rails
3
solid rail
solid rail
* Assemble frame
except for split rails.
Page 1
Instruction Sheet
EconoStand™ with AnoFrame™
(continued on other page)
Finished look
Parts
Step 3
Assemble bottom holder bracket onto
lower pole section (this is the thicker
section of the pole.
Step 4
Screw pole onto baseplate.
Tighten securly.
Step 5
Place stand upright. Using thumbscrew
at top of pole, attach top holder
bracket onto pole top.
Step 6
Slide top and bottom rails onto
holder brackets.
Step 7
Assemble split rails onto side ends
of solid rails, one inside and one
outside of each side of the AnoFrame.
Fig. 7 & 8
Step 8
Adjust height of stand as necessary.
Instructions for Assembly
Incept-9.10.02
EconoStand
components
The AnoFrame and EconoStand are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSEcono/AnoFrame
Base
Plate
Pole
To p
Holder Bracket
Bottom
Holder Bracket
Top
Thumb
Screw
3 4
56
7 8
Instruction Sheet
EconoStand™ with AnoFrame™
Page 2
Finished look
/