ROSE DISPLAYS ANOGOTCHA STAND WITH TOPPER Instruction Sheet

Brand: ROSE DISPLAYS

Model: ANOGOTCHA STAND WITH TOPPER

Type: Instruction Sheet

ROSE DISPLAYS ANOGOTCHA STAND WITH TOPPER is a versatile and durable display stand designed to securely hold and display graphics and posters of various sizes. It features a sturdy 9" round base and two vertical poles that provide stability and support for the AnoGotcha holders. The T-Gotcha holders securely grip the top and bottom edges of the graphic, ensuring a taut and professional presentation.

The stand's adjustable height allows for customization to accommodate graphics of different lengths, making it suitable for various applications such as trade shows, exhibitions, retail displays, and office presentations. Additionally, the included Topper Clips enable the attachment of a header or topper graphic to the top of the stand, providing an extra level of visibility and branding.

9” round base

vertical post

ball knobs

top AnoGotcha holder

bottom AnoGotcha holder

AnoGotcha

Shell

12AT300

9” round base

97-0302

AnoGotcha™Stand with Topper Clips

Instruction Sheet

T-Gotcha

12GT100

These are all the parts required to assemble 1 AnoGotcha Stand.

Parts

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any

sales agent may be held liable for injury, loss or damage resulting from the use of these products.

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

Finished look.

Read this instruction sheet care-

fully before assembly. Separate

all parts and check quantities.

Make sure all parts are account-

ed for before discarding any

packaging materials.

If you experience any problems

with the assembly, please call

Rose Displays at

1-800-631-9707.

vertical poles

97-0301 ball knobs &

threaded rods

97-0303

97-0304

shaped

end caps

97-0305

Important terms:

Topper Clips

06-6100

Topper Clip

Screw ball knobs onto threaded rods.

Step 1

AnoGotcha™Stand assembly continued

•Locate four ball knobs and

two threaded rods.

•Screw one ball knob

onto one end of each

threaded rod.

Note:

Do not screw a ball

knob onto both ends

of threaded rods.

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any

sales agent may be held liable for injury, loss or damage resulting from the use of these products.

Part #02INSAnoGotchaStandTopper

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:[email protected]

Screw vertical poles onto 9” round bases.

Step 2

•Screw the end of one

vertical pole onto the

threaded stud of each

9” round base.

• Repeat for both poles.

Screw one ball knob on one end of

threaded rod and tighten. You should have one ball knob on one end of each threaded rod.

Screw one vertical pole onto each

9” round base. Tighten with hands.

You should have two matching vertical poles with bases.

vertical

pole

9” round

base

Insert T-Gotcha holders into AnoGotcha shells.

Step 3

AnoGotcha™Stand assembly continued

• Slide one T-Gotcha holder

into each AnoGotcha shell.

•Attach one shaped end

cap onto each end of both

AnoGotcha shells.

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any

sales agent may be held liable for injury, loss or damage resulting from the use of these products.

Part #02INSAnoGotchaStandTopper

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:[email protected]

Attach top AnoGotcha holder onto vertical poles.

Step 4

•Slide one threaded rod with

ball knob (created in step 1)

through top hole in one

vertical pole (created in

step 2).

• Slide threaded rod

completely through top

channel of one AnoGotcha

holder (created in step 3)

and through top hole of

second vertical pole.

• Screw second ball knob

onto other end of threaded

rod. Tighten securely.

Slide T-Gotcha holder into each

AnoGotcha shell as shown. Attach one shaped end cap onto

each end of AnoGotcha holders,

as shown.

You should have two AnoGotcha holders with one

shaped end cap on each end.

Slide threaded rod through the

top hole of one vertical pole and

then through top channel of one

AnoGotcha holder.

Slide threaded rod through top hole

in second vertical pole. Screw ball

knob tightly onto threaded rod. Your stand should now look like this.

T-Gotcha

shaped

end cap

vertical

pole

top

AnoGotcha

holder

9” round

base

ball knobs

AnoGotcha

shell

Attach bottom AnoGotcha holder to vertical poles.

Step 5

AnoGotcha™Stand assembly continued

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any

sales agent may be held liable for injury, loss or damage resulting from the use of these products.

Part #02INSAnoGotchaStandTopper

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:[email protected]

Slide threaded rod through height

slot that matches the length of your

graphic and through bottom channel

of remaining AnoGotcha holder.

Slide threaded rod through matching

hole on opposite vertical pole. Attach ball knob, but do not

tighten. Leave loose until

graphic is inserted.

Bottom AnoGotcha must be

attached at slot that matches

the length of your graphic.

60”

48”

28”

60”

48”

•Choose the height slot

that matches the length

of your graphic.

•Slide one threaded rod with

ball knob (created in step 1)

through appropriate hole in

one vertical pole (created in

step 2) and through bottom

channel of one AnoGotcha

holder (created in step 3).

•Slide threaded rod through

corresponding slot of second

vertical pole.

Note:

Make sure the hinge on the

bottom T-Gotcha faces up

and in the same direction as

the hinge on the T-Gotcha

at the top of the stand.

• Loosely screw second

ball knob onto end of

threaded rod.

Note:

Ball knob must be kept loose

until graphic is inserted.

T-Gotcha hinge must face up and in the same direction as T-Gotcha on the top.

Turn ball knob in your right

hand away from you.

Hold both knobs and pull down

slightly to tension graphic.

Insert your graphic into AnoGotcha Stand.

Step 6

• Open top AnoGotcha

holder and insert top

edge of your graphic

until it reaches the

top of the holder.

Snap shut top holder.

• Open the bottom

AnoGotcha holder and

insert bottom edge of your

graphic until it reaches the

bottom of the holder. Snap

shut bottom holder.

AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any

sales agent may be held liable for injury, loss or damage resulting from the use of these products.

Part #02INSAnoGotchaStandTopper

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:[email protected]

Tension poster and tighten bottom AnoGotcha holder.

Step 7

•Hold both ball knobs on

bottom AnoGotcha holder,

and pull down slightly,

to tighten and straighten

your graphic.

• Turn ball knobs in opposite

directions to secure bottom

AnoGotcha holder.

Your AnoGotcha stand is now

complete and ready for display.

Your completed AnoGotcha Stand

should look similar to this.

Insert graphic into top

AnoGotcha holder. Snap the holder shut. Snap the holder shut.Insert graphic into bottom

AnoGotcha holder.

Poster inserted into top AnoGotcha holder.Poster inserted into bottom AnoGotcha holder.

To tighten, turn ball knob in

your left hand towards you.

AnoGotcha™Stand assembly continued

Attach Topper Clips onto top rail of AnoGotcha.

Step 8

The AnoGotcha Stand is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor

any sales agent may be held liable for injury, loss or damage resulting from the use of these products.

Part #02INSAnoGotchaStandTopper

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:[email protected]

• Push both Toppers Clips

onto top rail of AnoGotcha

holder and place one at

each end of rail.

• Insert poster into

Topper Clips.

Squeeze top tabs together to open

Topper Clip. While open, push

Topper Clip onto rail until it snaps

into place. Repeat for multiple

Topper Clips.

Insert graphic into top clip of Topper

Clip. Be sure to push graphic

completely into clip. Finished Look

AnoGotcha™Stand assembly continued

If you have any questions about your AnoGotcha Stand assembly, please call

Rose Displays at 1-800-631-9707 and we will assist you.

ROSE DISPLAYS ANOGOTCHA STAND WITH TOPPER Instruction Sheet

ROSE DISPLAYS ANOGOTCHA STAND WITH TOPPER Instruction Sheet

ROSE DISPLAYS ANOGOTCHA STAND WITH TOPPER Instruction Sheet

Related papers

Other documents