© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-22-20
INSTALLATION Accessories - Q-ANGLE
2
9
4
8
5
10
3
7
1
6
1
6
3
8
5
10
2
7
4
9
COMPONENTS
Top Lock Locking Hole
Locking Gear
Mounting Surface
Base Wood Screw Insert Location
Serrated Teeth
Angle Indicators
Angle Dial
Wire Way
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-22-20
INSTALLATION Accessories - Q-ANGLE
Required Hardware:
• 2 x 6-32 Fillister head screw
• 2 x 4-40 Flat head screw
• 2 x Mounting Clip
Shipped with fixture seperately
• 2 x Drywall anchors
For drywall applications only (not provided)
• 4 x #6 Wood screw
• Once mounted, take the top lock and connect it to
the base of the NON WIREWAY Q-ANGLE and choose your
desired angle.
3
Mounting Options:
• Mount both the bases onto the surface using
the supplied wood screws or suggested drywall anchors.
2
X
X
90° 270°
240°
210°
180°
150°
120°
• Determine where you want to install the Q-ANGLE, either
into a stud or drywall. (drywall anchors not provided)
1
Compatible Products
All Extrusions
Angle dial markings
• Using the Fillister head screw and a Phillips screw
driver, tighten the top lock into the base of the
NON WIREWAY Q-ANGLE onto the selected preset angle.
4
8” 8”
10’
8’
2’
2” 2”
4’
4” 4”
12” 12”
EXTRUSIONS: Mount from end
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-22-20
INSTALLATION Accessories - Q-ANGLE
5
• Once fed through, secure the top lock onto the WIREWAY
Q-ANGLE base and tighten with a Phillips screw driver. Make sure
to use the angle indicators to match the first installed setup.
8
Angle Indicator
• Secure the extrusions’s mounting clip onto the face of
BOTH top locks using the provided 4-40 flat head screw.
6
7
• Feed the lead wire from the fixture into the WIREWAY
Q-ANGLE to connect with the power supply.
• Now that the mounting clip is secured, mount the
extrusion fixture onto each Q-ANGLE ensuring they snap in.
• The Q-ANGLE and the selected fixture should now be
completely assembled and mounted into the desired location.
9
To adjust the angle after
installation, Repeat Step 7.
WIRE WAYNON WIRE WAY
Shows TORQ assembled with Q-Angle
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-22-20
INSTALLATION Accessories - Q-ANGLE
• 2 x 6-32 Fillister head screw
• 2 x 4-40 Flat head screw
• 2 x Rigid Lock Channel & Retainer Clip
Shipped with fixture seperately
• 2 x #8-32 Set Screw
Shipped with Rigid Lock Channel
• 2 x Drywall anchors
For drywall applications only (not provided)
• 4 x #6 Wood screw
• 1 x 5/64 Allen Key
Shipped with Rigid Lock Channel
• Once mounted, take the top lock and connect it to
the square base of the NON WIREWAY Q-ANGLE and
choose your desired angle.
3
• Mount both the bases onto the surface using the
supplied wood screws or suggested drywall anchors.
2
X
X
90° 270°
240°
210°
180°
150°
120°
• Determine where you want to install the Q-ANGLE, either
into a stud or drywall. (drywall anchors not provided)
1
Compatible Products
BOXA, KURV, ZALA
(non Pool & Spa)
Angle dial markings
1.0”
.84”
1.0”
FLEXIBLE FIXTURES: Mount every 12”
12” 12” 12”
• Using the Fillister head screw and a Phillips screw
driver, tighten the top lock into the base of the
NON WIREWAY Q-ANGLE onto the selected preset angle.
4
Required Hardware: per 12” installation Mounting Options:
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-22-20
INSTALLATION Accessories - Q-ANGLE
5
• Once fed through, secure the top lock onto the wireway
square base and tighten with a Phillips screw driver. Make sure
to use the angle indicators to match the first installed setup.
8
10
• Secure the Rigid Lock Channel onto the face of
BOTH top locks using the provided 4-40 flat head screw.
• Push Retainer Clip onto fixture.
• Mount the fixture onto each Q-Angle ensuring that each
Retainer Clip snaps into the RLC.
6
7
9
• Feed the lead wire from the fixture into the wireway
Q-ANGLE to connect with the power supply.
• Tighten each RLC to the fixture by using the set screw
and the supplied Allen key.
Angle Indicator
WIRE WAYNON WIRE WAY
/
