Q-tran LALO-FLAT-OC Linear Fixture User manual

Type
User manual

This manual is also suitable for

INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 1
COMPLIANT 5YEAR
WARRANTY
LALO-FLAT-OC (01)
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 2
COMPLIANT 5YEAR
WARRANTY
2
METHODS OF INSTALLATION: LALO-FLAT-OC can be recessed in millwork with all compatible LED strips except SW-
HE24/9.0.
Stainless Steel Mount Additional Mounting
(Sold separately)
WALL
WALL
VHB Tape
Sold separately
Magnet Mount
HINGE BRACKET
Q-ANGLE
Q-PIVOT
Adhesive Mount
Silicone
Sold separately
832
12"
.75"
.23"
2.5"
.64"
1.25"
.20"
.20"
.81"
MG-01MMA-01
Sold separately
SST-01
.20
.81
1.25
.26
"
.625"
.21
"
.625"
#4 x 5/8"
Flat Head SS
#6 x 5/8"
Flat Head SS
CONCRETE
FLOOR
Not rated for walkover
CEILING
1.38"
1.50"
2.23"
1.93"
WALL
HMB-L
1.46"
1.29"
HMB-XL 1.46"
4.00"
HMB-M
0.71"
1.41"
0.85"
1.03"
0.75"
Surface Mounting Method
VHB Mount (page 5-6)
Silicone Mount (page 7)
Screw Mount (page 8)
Magnet Mount (page 9)
Recessed Mounting Method
Magnet Mount : Millwork (page 10)
ATTENTION: Please read all instructions BEFORE installation
Product to be installed by a licensed electrician - Field modifications void warranty
Use only with Class 2 power supply unit — Compatible for use with Q-Tran power supplies
Surface mount or recessed in millwork
Suitable for installation in storage area of a clothes closet when assembled as a finished fixture up to 4W/ft at Q-Tran facility
Not rated for walkover
Input Voltage: 24VDC
Diagrams for representation only and not to scale.
Cove, Under &
over cabinet:
Ideal for oce, retail,
hospitality, education,
laboratory, and
residential.
Shelf:
Ideal for oce, retail,
hospitality, education,
laboratory, and
residential.
Display cabinet:
Ideal for retail and
hospitality.
Signage:
Ideal for lobby, retail,
hospitality, institutional,
and transportation.
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 3
COMPLIANT 5YEAR
WARRANTY
3
COMPONENTS & HARDWARE
NOTES:
STAINLESS STEEL CLIP MAGNET CLIP
2 clips provided for 4’ or less; 4 clips provided for greater than 4’ One magnet clip per foot
MMA-01 comes in 12” pieces; use at least one clip per MMA-01 accessory
MMA-01 can be cut into smaller pieces, if desired
STAINLESS STEEL CLIP MAGNET CLIP
SST-01
.20
"
.81"
1.25"
MG-01
1.25"
.20
"
.20
"
.81"
.21
"
.625"
Included
Flat Head Screw
#4x5/8”
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
ADHESIVE SOLD SEPARATELY
SILICONE VHB TAPE; sold in 15’ increments
DOWSIL 832 TAPE-VHB-IP20
832
ACCESSORIES SOLD SEPARATELY
MAGNET MOUNT ACCESSORY;
sold individually
HINGE BRACKET;
sold individually
Q-ANGLE;
sold in pairs
Q-PIVOT;
sold in pairs
HMB-M
HMB-L
HMB-XLMMA-01 Q-ANGLE Q-PIVOT
Included
• 4 SS #6x1.25”
Flat head wood screws
• 2 SS 4-40
Flat head clip screws
• 2 SS 6-32
Fillister screws
Included
• 3/4” long mount screw
• 1/4” #4 clip mount
screw
Included
• SS #4-40x3/16
Flat head screws
• 2 #4x3/4
Pan Head screws
Included
• 2 #6x5/8”
Flat Head SS
Image shows
HMB-M
12"
.75"
.23"
2.5"
.64"
1.38"
1.50"
2.23"
1.93"
0.85"
1.03"
0.75"
Profile with
flat lens
.58
".42
"
.56"
.36"
.70"
Profile with flat lens
stainless steel
mounting clip
".64
Profile with flat lens
magnet mounting clip
.81"
.84
"
.68
"
.20"
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 4
COMPLIANT 5YEAR
WARRANTY
4
CONTINUOUS WIRING CONFIGURATION OPTIONS
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
.08"
.08"
P1
S1
.16"
P2
S2
Review wire method to ensure clean installation prior to mounting finished Fixture.
NOTE: Additional wire methods include:
S1 & S2: Connector/Wire Input only
P1 & P2: Connector/Wire Input and Output
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 5
COMPLIANT 5YEAR
WARRANTY
5
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
SURFACE MOUNTING METHOD
SURFACE PREPARATION
For porous materials (Wood, Brick, Concrete etc.) apply two
layers of paint or primer to the surface. This will help create
a better bonding surface for these materials. These can be
purchased from a local hardware store.
a. Using a 50/50 alcohol mix, thoroughly clean the backside of
the Fixture and the surface area where Fixture will be installed.
Allow 5 minutes to dry.
b. Peel back 0.5" of the VHB tape’s protective film on one end
and use firm pressure to adhere it to the desired surface,
avoiding air bubbles. Continue peeling the film and adhering
the tape in small sections until the entire length is installed.
Temperature and environmental concerns:
• Ideal application environment is 70-100ºF in 50% humidity
or less.
• Minimum application temperature: 50ºF
• This temperature and humidity should be maintained for
72 hours after application for maximum bond strength.
50% humidity
or less
70-100ºF 72 hrs
Paint or
3M
Primer 94
Wood Brick Concrete
1 layer 2 layers
MATERIALSSUGGESTED EPOXIES
Concrete, Stone, Cinderblock,
Metal, and Brick
Loctite Metal and
Concrete Two-Part Epoxy
ABS, Fiberglass,
Plastic, and PVC
Loctite Plastic
Two-Part Epoxy
Tile, Wood, Ceramic,
Glass, or Metal
Loctite Clear
Two-Part Epoxy
All Purpose Strong Stik
50/50
alc
5 mins
50/50
alc
a.
b.
1
3
2
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 6
COMPLIANT 5YEAR
WARRANTY
6
SURFACE MOUNTING METHOD: VHB ADHESIVE MOUNT
BEFORE installation, the surface must be thoroughly cleaned and dried for maximum bond strength. (page 5)
Length as needed
SURFACE MOUNTING METHOD: VHB ADHESIVE MOUNT
30
31
14
15
29
28
Length as needed
M
a
r
k
e
r
1
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
a.
b.
2
Determine the LALO-FLAT-OC fixture(s) location and
positioning on desired surface before adhering Fixture to
surface. Make any necessary reference markings to indicate
fixture placement.
Remove protective film from the surface of the fixture’s lens.
a. To adhere the VHB adhesive, peel the white film back while
evenly applying the tape to the mounting side of the
fixture. The red side should be visible.
b. Remove the red film and position fixture in place according
to your previous reference marking(s).
NOTES: EPOXY ALTERNATIVE: For improved bonding strength, apply a small amount of epoxy at each end. Refer to table on for suggested
epoxies. These can be purchased at a local hardware store. Please follow all manufacturer instructions for suggested epoxy.
1
3
2
page 5
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 7
COMPLIANT 5YEAR
WARRANTY
7
Remove protective film from the surface of the fixture’s lens.
Determine the LALO-FLAT-OC fixture(s) location and
positioning on desired surface; evenly distribute clips. Make
any necessary reference markings to indicate where each clip
is to be secured in place. Recommended every 24” - 30”.
a. Firmly press the silicone-coated clips on the marked
reference points.
b. Wait for silicone adhesive to cure completely before
snapping fixture into place.
c. Snap fixture onto clips.
NOTE: Cure time is dependent on the type of silicone adhesive used.
Refer to silicone product manufacturer for accurate drying time.
SURFACE MOUNTING METHOD: SILICONE
2 clips provided for 4’ or less; 4 clips provided for greater than 4’
24" - 30"4" 4"
30
31
14
15
29
28
24" - 30"
M
a
r
k
e
r
3
1
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
24" - 30"
832
a.
b.
c.
2
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 8
COMPLIANT 5YEAR
WARRANTY
8
SURFACE MOUNTING METHOD: SCREW MOUNT
24" - 30"4" 4"
2 clips provided for 4’ or less; 4 clips provided for greater than 4’
30
31
14
15
29
28
24" - 30"
M
a
r
k
e
r
SURFACE MOUNTING METHOD: SCREW MOUNT
2 clips provided for 4’ or less; 4 clips provided for greater than 4’
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
24" - 30"
a.
b.
c.
Determine the LALO-FLAT-OC fixture(s) location and
positioning on desired surface; evenly distribute clips. Make
any necessary reference markings to indicate where each clip
is to be secured in place. Recommended every 24” - 30”.
a. Secure clips using the #4 flat head hardware provided.
b. Ensure the screw head is flush with the clip’s base.
c. Snap fixture onto clips.
NOTE: Flat head screw type is dependent on surface/application material.
Alternative flat head screws may be required. Refer to the surface material
manufacturer for suggested screw type.
Remove protective film from the surface of the fixture’s lens.
1 2
3
INSTALLATION INSTRUCTIONS
LINEAR FIXTURE - LALO-FLAT-OC
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-23-22 9
COMPLIANT 5YEAR
WARRANTY
9
a. Mount the two #6 flat head screws into the 12” magnet
mount accessory bracket through the slotted holes at
each end. Ensure the screw head is flush with the magnet
mount bracket.
b. Snap the magnet clips onto the backside of the fixture.
They should be offset to the accessory bracket screws to
maximize magnetic connection.
c. Place the assembled fixture into the magnet mount bracket.
NOTE: If surface application requires a longer screw, the screw size must
be a #6 Flat Head.
SURFACE MOUNTING METHOD: MAGNET MOUNT
One magnet clip per foot
MMA-01 comes in 12” pieces; use at least one clip per MMA-01 accessory
MMA-01 can be cut into smaller pieces, if desired
30
31
14
15
29
28
Length as needed
M
a
r
k
e
r
1
SURFACE MOUNTING METHOD: MAGNET MOUNT
COMPONENTS &
HARDWARE
METHODS &
INSTALLATIONS MOUNTING
WIRING OPTIONS
4" 4"
a.
b.
c.
2
Remove protective film from the surface of the fixture’s lens.
Determine the LALO-FLAT-OC fixture(s) location and
positioning on desired surface. Make any necessary reference
markings to indicate where the magnet mount accessory
bracket is to be secured in place.
3
1 2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Q-tran LALO-FLAT-OC Linear Fixture User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI