Q-tran HINGE Adjustable Light Fixture Bracket Installation guide

Brand: Q-tran

Model: HINGE Adjustable Light Fixture Bracket

Type: Installation guide

This manual is also suitable for

Q-TRAN HINGE Adjustable Light Fixture Bracket

INSTALLATION Accessories - HINGE

NOTES:

• Not recomended for use with flexible encapsulated fixtures

• Compatible with MICRO 5 rigid fixtures

• Compatible with extrusions with lens

• Compatible with rigid encapsulated fixtures

• Mount to drywall with drywall anchors or mount to wood surface

INCLUDED PARTS:

• Assembled bracket

• 3/4" long mounting screw(s)

• 6-32 x 1/4” undercut flat head mounting

clip screw

• Allen key 5/64" (for HMB-S & HMB-M)

or 3/32" (for HMB-L & HMB-XL)

TOOLS & HARDWARE NEEDED:

• Drywall anchors (if mounting to drywall)

• Screw driver

• Measuring tape

INSTALLATION Accessories - HINGE

HMB-S FOR MICRO 5 SERIES ONLY

HMB-L & HMB-XL FOR MICRO 5 SERIES STANDARD & ENCAPSULATED FIXTURES

HMB-M FOR MICRO 5 SERIES & STANDARD LINEAR FIXTURES

STANDARD & ENCAPSULATED - Ceiling, Wall & Floor Mount

STANDARD - Ceiling, Wall & Floor Mount

ENCAPSULATED - Ceiling, Wall & Floor Mount

NOTE: ADDITIONAL BRACKETS CAN BE USED IF NEEDED

STANDARD - Wall & Floor Mount

12” 12”36”36”

2 BRACKETS FOR 4 FEET OR LESS

3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)

12” 36” 36” 12”

6” 24” 18”

18” 24” 6”

2 BRACKETS FOR 4 FEET OR LESS

3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)

2 BRACKETS FOR 4 FEET OR LESS

4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)

12” 36” 36” 12”

6” 24” 18”

18” 24” 6”

2 BRACKETS FOR 4 FEET OR LESS

3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)

2 BRACKETS FOR 4 FEET OR LESS

4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)

12” 12”

2 BRACKETS FOR 4 FEET OR LESS

3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)

36”36”

6” 6”

2 BRACKETS FOR 4 FEET OR LESS

4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)

24”24” 36”

12” 12”

2 BRACKETS FOR 4 FEET OR LESS

3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)

36”36”

6” 6”

2 BRACKETS FOR 4 FEET OR LESS

4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)

24”24” 36”

ENCAPSULATED - Ceiling, Wall & Floor Mount

ADDITIONAL BRACKET RECOMMENDED AT CENTER OF

RUN WHEN MOUNTING MULTIPLE FIXTURES

INSTALLATION Accessories - HINGE

Install fixture mount clip with provided SS #6 flat head screw

from bag.

NOTE: Screw can only be installed once so make sure

correct position is configured. Do not over torque. Hand

tighten until firm.

HMB-S

FOR MICRO 5 SERIES OR SMALL FIXTURES

Screw down base bracket with provided screw or equivalent.

Remove HMB-S from bag. Loosen side screws with 5/64 allen

wrench and rotate inner bracket to reveal mounting hole.

Snap fixture onto bracket. Rotate inner bracket to desired angle

then tighten side screws to lock angle.

FINISHED CLIP

SIDE VIEW

0-120°

INSTALLATION Accessories - HINGE

Install fixture mount clip with provided SS #6 flat head screw

from bag.

NOTE: Screw can only be installed once so make sure

correct position is configured. Do not over torque. Hand

tighten until firm.

HMB-M

FOR LIGHT-WEIGHT LINEAR FIXTURES

Screw down base bracket with provided screw or equivalent.

Remove HMB-M from bag. Loosen side screws with 5/64 allen

wrench and rotate inner bracket to reveal mounting hole.

Snap fixture onto bracket. Rotate inner bracket to desired angle

then tighten side screws to lock angle.

FINISHED CLIP

SIDE VIEW

0-120°

INSTALLATION Accessories - HINGE

Install fixture mount clip with provided SS #6 flat head screw

from bag.

NOTE: Screw can only be installed once so make sure

correct position is configured. Do not over torque. Hand

tighten until firm.

HMB-L

FOR HEAVY LINEAR FIXTURES

Screw down base bracket with provided screw or equivalent.

Lower down by pushing anchor in arrows direction. Lock by

pushing in opposite direction.

Remove HMB-L from bag. Loosen side screws with 3/32 allen

wrench and rotate inner bracket to reveal mounting hole.

Snap fixture onto bracket. Rotate inner bracket to desired angle

then tighten side screws to lock angle.

FINISHED CLIP

SIDE VIEW

0-88°

INSTALLATION Accessories - HINGE

Install fixture mount clip with provided SS #6 flat head screw

from bag.

NOTE: Screw can only be installed once so make sure

correct position is configured. Do not over torque. Hand

tighten until firm.

HMB-XL

FOR HEAVY LINEAR FIXTURES & ANGLE HEIGHT CONTROL

Screw down base bracket with provided screw or equivalent.

Lower down by pushing anchor in arrows direction. Lock by

pushing in opposite direction.

Remove HMB-XL from bag. Loosen side screws with 3/32 allen

wrench and rotate inner bracket to reveal mounting hole.

Snap fixture onto bracket. Rotate inner bracket to desired angle

then tighten side screws to lock angle.

FINISHED CLIP

SIDE VIEW

4" long

0-88°

INSTALLATION Accessories - HINGE

HMB-XL

FIELD MOUNT AND CUSTOM INSTALL FEATURES

CUSTOM CUTS - Field cuttable to smaller lengths

CUSTOM FIXTURE MOUNT

• Custom install 3 fixtures on wall or floor at 24" spacing

• MICRO 5 standard and encapsulated fixtures or standard linear fixtures

24” 24”

2”

3”

4”

INSTALLATION Accessories - HINGE

PRE-SET ANGLES FOR HMB-L & HMB-XL

1ST NOTCH

HMB-L HMB-XL

2ND NOTCH

3RD NOTCH

4TH NOTCH

11°

35°

58°

88°

Q-tran HINGE Adjustable Light Fixture Bracket Installation guide

Brand: Q-tran

Model: HINGE Adjustable Light Fixture Bracket

Type: Installation guide

This manual is also suitable for

Q-TRAN HINGE Adjustable Light Fixture Bracket

Download PDF

report

Q-tran HINGE Adjustable Light Fixture Bracket Installation guide

This manual is also suitable for

Q-tran HINGE Adjustable Light Fixture Bracket Installation guide

Related papers

Other documents