Halco WPFS2-WS-CS-U-PC Installation guide

Halco
Brand
Halco
Model
WPFS2-WS-CS-U-PC
Type
Installation guide

This manual is also suitable for

WARNING: RISK OF ELECTRICAL SHOCK
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code and any applicable local
code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION: RISK OF INJURY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing
maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION: RISK OF FIRE
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• MIN 90°C SUPPLY CONDUCTORS.
Illustrations in the manual are for installation purposes only. It may not be identical to the xture purchased.
GENERAL WIRING DIAGRAM
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring xture to the power supply.
© 2019 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies. All sizes and specications are subject to change. Print Edition 11-13-19.
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Cleveland | Houston | Los Angeles | Phoenix
Wallpack Installation Instructions
®
GENERAL SAFETY INFORMATION
• To reduce the risk of death, personal injury or property damage from re, electric shock,
falling parts, cuts/abrasions, and other hazards read all warnings and instructions included
with and on the xture box and all xture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow
these general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a
qualied licensed electrician.
• For Residential installation: If you are unsure about the installation or maintenance of the
luminaires, consult a qualied licensed electrician and check your local electrical code.
• DO NOT INSTALL DAMAGED PRODUCT!
• This xture is intended to be connected to a properly installed and grounded UL listed
junction box.
• Voltage input: 120-277V 50/60 Hz only
(+)LINE
(-)COMMON
GROUND
BLACK
Light
Fixture
WHITE
GROUND
STEP 1
Loosen two captive screws on side of housing and remove front housing. Remove knockout
plug on the back of the xture. Drill appropriate points and attach using appropriate hardware
(not included).
Note: LED xtures utilizes a mult-volt (120-277V) that is auto sensing, no rewiring is necessary.
STEP 4
Check to make sure that the supply voltage to the xture is compatible with the driver (120-277).
Connect the white xture wire to the white supply wire. Connect the black xture wire to the
black supply wire. Connect the green xture wires to the ground wire. Make sure all connections
are secure using approved connecting devices.
Note: LED xtures utilizes a mult-volt (120-277V) that is auto sensing, no rewiring is necessary.
STEP 5
Seal with weatherproof silicone
sealant to prevent moisture from
entering the fixture. Replace front
housing, reconnect plug.
STEP 6
Tighten two captive screws
on side of housing.
© 2019 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies. All sizes and specications are subject to change. Print Edition 11-13-19.
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Cleveland | Houston | Los Angeles | Phoenix
Wallpack Installation Instructions
®
MOUNTING INSTRUCTIONS
Photocell function
Photocell configured to the device, default setting: ambient brightness is
< 10 lux, light on; while ambient brightness is > 30 lux, light off. Other
settings refer to following diagrams.
Outgoing line direction
STEP 2 Remove the plug STEP 3 Install photocell
PHOTOCELL WIRING DIAGRAM
  • Page 1 1
  • Page 2 2

Halco WPFS2-WS-CS-U-PC Installation guide

Halco
Brand
Halco
Model
WPFS2-WS-CS-U-PC
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents