Halco HID54/840/LED3 84314 Operating instructions

HID54/840/LED3 84314
Halco
Brand
Halco
Model
HID54/840/LED3 84314
Category
Floodlights
Type
Operating instructions
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Chicago | Cleveland | Houston | Los Angeles | Phoenix
®
© 2019 Halco Lighting Technologies, LLC. All rights reserved. Halco is a registered trademark of Halco Lighting Technologies. All sizes and specications are subject to change.
Please read the below articles carefully to see how to use this product safely.
Warning contents and attention contents related to product safety use, please be sure to follow it.
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
LED HID REPLACEMENT LAMP INSTALLATION GUIDE
Caution-IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC), IMMEDIATELY TURN OFF
POWER , REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER OR DISTRIBUTOR.
WARNING - Follow the installation instructions to install correctly.
• Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
• This item is rated at 120-277VAC/100-240VAC. Installer must determine whether line voltage 120-277VAC/100-240VAC is available at
the luminaire before installation.
• Not intended for use with emergency exit fixtures or emergency exit lights.
• Not for use with luminaire ballast.
• Do not use if product is damaged.
• This lamp is non-dimmable. Not for use with dimmer.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead
installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires
by employing applicable connections.
• Suitable for damp locations. Suitable for use in wet locations when used in
an outdoor -rated fixture. Not for use where directly exposed to
the weather or water
• Complies with part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference , and
(2) This device must accept any interference received including interference that may cause undesired operation.
• No external weight or mechanical force should be applied to lamp or components.
• THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
BEFORE YOU BEGIN
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. TO AVOID PERSONAL INJURY AND /OR PRODUCT
DAMAGE. ALL OF THE INSTRUCTIONS BELOW MUST BE FOLLOWED.
1
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
LED HID REPLACEMENT LAMP INSTALLATION GUIDE
Caution-IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC), IMMEDIATELY TURN OFF
POWER , REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER OR DISTRIBUTOR.
WARNING - Follow the installation instructions to install correctly.
• Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
• This item is rated at 120-277VAC/100-240VAC. Installer must determine whether line voltage 120-277VAC/100-240VAC is available at
the luminaire before installation.
• Not intended for use with emergency exit fixtures or emergency exit lights.
• Not for use with luminaire ballast.
• Do not use if product is damaged.
• This lamp is non-dimmable. Not for use with dimmer.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead
installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires
by employing applicable connections.
• Suitable for damp locations. Suitable for use in wet locations when used in a
n outdoor -rated fixture. Not for use where directly exposed to
the weather or water
• Complies with part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference , and
(2) This device must accept any interference received including interference that may cause undesired operation.
• No external weight or mechanical force should be applied to lamp or components.
• THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
BEFORE YOU BEGIN
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. TO AVOID PERSONAL INJURY AND /OR PRODUCT
DAMAGE. ALL OF THE INSTRUCTIONS BELOW MUST BE FOLLOWED.
1
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
LED HID REPLACEMENT LAMP INSTALLATION GUIDE
Caution-IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING, FLICKERING, ETC), IMMEDIATELY TURN OFF
POWER , REMOVE LAMP FROM LUMINAIRE AND CONTACT THE MANUFACTURER OR DISTRIBUTOR.
WARNING - Follow the installation instructions to install correctly.
• Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
• This item is rated at 120-277VAC/100-240VAC. Installer must determine whether line voltage 120-277VAC/100-240VAC is available at
the luminaire before installation.
• Not intended for use with emergency exit fixtures or emergency exit lights.
• Not for use with luminaire ballast.
• Do not use if product is damaged.
• This lamp is non-dimmable. Not for use with dimmer.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
• Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead
installers should cut existing lamp holder leads away fr
om the lamp holder and make new electrical connections to lamp holder lead wires
by employing applicable connections.
• Suitable for damp locations. Suitable for use in wet locations when used in an outdoor -rated fixture. Not for use where directly exposed to
the weather or water
• Complies with part 15 of FCC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference , and
(2) This device must accept any interference received including interference that may cause undesired operation.
• No external weight or mechanical force should be applied to lamp or components.
• THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
BEFORE YOU BEGIN
READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. TO AVOID PERSONAL INJURY AND /OR PRODUCT
DAMAGE. ALL OF THE INSTRUCTIONS BELOW MUST BE FOLLOWED.
1
ProLED
®
HID Retrot
Installation Instructions
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
2
5. Install LED lamp into the socket.
6. Turn on the power to the fixture.
1. Turn off the power to the fixture.
2. Remove existing HID lamp from the fixture.
3. Open the fixture ‘s junction box and bypass the HID ballast , igniter (If there) and the capacitor (If there) by disconnecting the line and neutral
wires and socket black and white wires in the locations with “Cross” marks in the schematic diagram. Then connect the line to the black wire
from the socket and the neutral to the white wire from the socket with wire nuts or connectors.
4. 'This luminaire has been modified to operate LED lamps' shall be marked on the retrofit luminaire where readily visible by the user during
normal maintenance including re-lamping.
OFF
STEP 1 STEP 2
STEP 4
T h e l u m i n a i r e h a s b e e n
modified and can no longer
operate the originally intended
lamp , refer to the LED retrofit
lamp installa tion guide for
l u m i n a i r e r e t r o f i t wiri n g
inst ru ctions. Use th e LE D
retrofit lamp for lamp replace-
ment.
STEP 3
Capacitor
Lgnitor
Lamp socket
Ballast
L
N
L
N
Wire nut
Wire nut
X
X
XX
.
STEP 5
© 2019 Halco Lighting Technologies, LLC. All rights reserved. Halco is a registered trademark of Halco Lighting Technologies. All sizes and specications are subject to change.
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Chicago | Cleveland | Houston | Los Angeles | Phoenix
Warranty Information:
This product is warranted for ve years from the date of purchase.
If this product does not perform to the specications supplied on this package, send an email or write to the address below for product return and
replacement. This replacement is the sole remedy available. Liability for incidental or consequential damage is expressly excluded.
Visit www.halcolighting.com for full warranty details and compatibility information.
Product Dimension
  • Page 1 1
  • Page 2 2

Halco HID54/840/LED3 84314 Operating instructions

HID54/840/LED3 84314
Halco
Brand
Halco
Model
HID54/840/LED3 84314
Category
Floodlights
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents