© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
NOTES:
• Not recomended for use with flexible encapsulated fixtures
• Compatible with MICRO 5 rigid fixtures
• Compatible with extrusions with lens
• Compatible with rigid encapsulated fixtures
• Mount to drywall with drywall anchors or mount to wood surface
INCLUDED PARTS:
• Assembled bracket
• 3/4" long mounting screw(s)
• 6-32 x 1/4” undercut flat head mounting
clip screw
• Allen key 5/64" (for HMB-S & HMB-M)
or 3/32" (for HMB-L & HMB-XL)
TOOLS & HARDWARE NEEDED:
• Drywall anchors (if mounting to drywall)
• Screw driver
• Measuring tape
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
HMB-S FOR MICRO 5 SERIES ONLY
HMB-L & HMB-XL FOR MICRO 5 SERIES STANDARD & ENCAPSULATED FIXTURES
HMB-M FOR MICRO 5 SERIES & STANDARD LINEAR FIXTURES
STANDARD & ENCAPSULATED - Ceiling, Wall & Floor Mount
STANDARD - Ceiling, Wall & Floor Mount
ENCAPSULATED - Ceiling, Wall & Floor Mount
NOTE: ADDITIONAL BRACKETS CAN BE USED IF NEEDED
STANDARD - Wall & Floor Mount
12” 12”36”36”
2 BRACKETS FOR 4 FEET OR LESS
3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)
12” 36” 36” 12”
6” 24” 18”
18” 24” 6”
2 BRACKETS FOR 4 FEET OR LESS
3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)
2 BRACKETS FOR 4 FEET OR LESS
4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)
12” 36” 36” 12”
6” 24” 18”
18” 24” 6”
2 BRACKETS FOR 4 FEET OR LESS
3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)
2 BRACKETS FOR 4 FEET OR LESS
4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)
12” 12”
2 BRACKETS FOR 4 FEET OR LESS
3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)
36”36”
6” 6”
2 BRACKETS FOR 4 FEET OR LESS
4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)
24”24” 36”
12” 12”
2 BRACKETS FOR 4 FEET OR LESS
3 BRACKETS FOR GREATER THAN 4 FEET (3 TOTAL FOR 8 FEET FIXTURE)
36”36”
6” 6”
2 BRACKETS FOR 4 FEET OR LESS
4 BRACKETS FOR GREATER THAN 4 FEET (4 TOTAL FOR 8 FEET FIXTURE)
24”24” 36”
ENCAPSULATED - Ceiling, Wall & Floor Mount
ADDITIONAL BRACKET RECOMMENDED AT CENTER OF
RUN WHEN MOUNTING MULTIPLE FIXTURES
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
Install fixture mount clip with provided SS #6 flat head screw
from bag.
NOTE: Screw can only be installed once so make sure
correct position is configured. Do not over torque. Hand
tighten until firm.
3
HMB-S
FOR MICRO 5 SERIES OR SMALL FIXTURES
Screw down base bracket with provided screw or equivalent.
2
Remove HMB-S from bag. Loosen side screws with 5/64 allen
wrench and rotate inner bracket to reveal mounting hole.
1
Snap fixture onto bracket. Rotate inner bracket to desired angle
then tighten side screws to lock angle.
FINISHED CLIP
SIDE VIEW
4
0-120°
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
Install fixture mount clip with provided SS #6 flat head screw
from bag.
NOTE: Screw can only be installed once so make sure
correct position is configured. Do not over torque. Hand
tighten until firm.
3
HMB-M
FOR LIGHT-WEIGHT LINEAR FIXTURES
Screw down base bracket with provided screw or equivalent.
2
Remove HMB-M from bag. Loosen side screws with 5/64 allen
wrench and rotate inner bracket to reveal mounting hole.
1
Snap fixture onto bracket. Rotate inner bracket to desired angle
then tighten side screws to lock angle.
FINISHED CLIP
SIDE VIEW
4
0-120°
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
Install fixture mount clip with provided SS #6 flat head screw
from bag.
NOTE: Screw can only be installed once so make sure
correct position is configured. Do not over torque. Hand
tighten until firm.
3
HMB-L
FOR HEAVY LINEAR FIXTURES
Screw down base bracket with provided screw or equivalent.
Lower down by pushing anchor in arrows direction. Lock by
pushing in opposite direction.
2
Remove HMB-L from bag. Loosen side screws with 3/32 allen
wrench and rotate inner bracket to reveal mounting hole.
1
Snap fixture onto bracket. Rotate inner bracket to desired angle
then tighten side screws to lock angle.
FINISHED CLIP
SIDE VIEW
4
0-88°
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
Install fixture mount clip with provided SS #6 flat head screw
from bag.
NOTE: Screw can only be installed once so make sure
correct position is configured. Do not over torque. Hand
tighten until firm.
3
HMB-XL
FOR HEAVY LINEAR FIXTURES & ANGLE HEIGHT CONTROL
Screw down base bracket with provided screw or equivalent.
Lower down by pushing anchor in arrows direction. Lock by
pushing in opposite direction.
2
Remove HMB-XL from bag. Loosen side screws with 3/32 allen
wrench and rotate inner bracket to reveal mounting hole.
1
Snap fixture onto bracket. Rotate inner bracket to desired angle
then tighten side screws to lock angle.
FINISHED CLIP
SIDE VIEW
4" long
4
0-88°
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
HMB-XL
FIELD MOUNT AND CUSTOM INSTALL FEATURES
CUSTOM CUTS - Field cuttable to smaller lengths
CUSTOM FIXTURE MOUNT
• Custom install 3 fixtures on wall or floor at 24" spacing
• MICRO 5 standard and encapsulated fixtures or standard linear fixtures
24” 24”
2”
3”
4”
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-01-18-22
INSTALLATION Accessories - HINGE
PRE-SET ANGLES FOR HMB-L & HMB-XL
1ST NOTCH
HMB-L HMB-XL
2ND NOTCH
3RD NOTCH
4TH NOTCH
11°
11°
35°
35°
58°
58°
88°
88°
/
