METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
1
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS OF INSTALLATION
COMPONENTS & HARDWARE
ATTENTION: Please read all instructions BEFORE installation
• Direct/Indirect fixture
• Input Voltage: 24VDC
• Diagrams for representation only and not to scale
• Product to be installed by a licensed electrician
• Indoor location only
• Diagrams for representation only and not to scale
• FIXTURE PREP: POWER FEED/NON-FEED (PAGE 2)
• SURFACE PREP: POWER FEED/NON-FEED (PAGE3)
• FINISHING FIXTURE: POWER FEED/NON-FEED (PAGE 11)
• WIRING DIAGRAM: PAGE 12
J-BOX FEED J-BOX NON-FEED TBAR-J-BOX FEED
TBAR-NON-FEED LAG SCREW-NON-FEED
ASSEMBLY A FIXTURE BOOM01-SINGLE KIT
STANDARD J-BOX TBAR-J-BOX HANGER
2
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• Install (4x)6-32 x 1/2” Counter Sunk screws and assembly B
onto fixture ends.
• Install (4x)6-32 x 1/2” Counter Sunk screws and assembly B
onto fixture ends.
• Route feed cable through the hole shown.
• a: From feed side snap strain relief around cable .
• b: Push down strain relief into plate.
POWER FEED NON-FEED
a b
FIXTURE PREP
POWER FEED / NON-FEED: J-BOX, TBAR-J-BOX GRID, TBAR-J-BOX-HANGER / LAG SCREW
see page 4 for J-BOX mount.
see page 6 for TBAR-J-BOX-GRID mount.
see page 8 for TBAR-J-BOX-HANGER mount.
see page 10 for LAG SCREW mount.
Number of lead wires will vary based on light engine and control
circuit selection. See wiring diagram on page 12-13 for connection
reference.
(4x)6-32 x 1/2” Counter Sunk
(4x)6-32 x 1/2” Counter Sunk
Assembly B
From BOOM01-SINGLE KIT
From BOOM01-SINGLE KIT
Assembly B
3
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• a: Determine the BOOM location and
positioning on desired surface before
mounting. Make any necessary reference
markings to indicate placement (see
page 6 for TBAR-J-BOX-GRID mount).
• b: Cut 2 holes in the ceiling at desired
location for junction box mounting per
size of junction box (see page 4 for
J-BOX or page 8 TBAR-J-BOX-HANGER
mount).
• c: Determine the BOOM location and
positioning on desired surface before
mounting. Make any necessary reference
markings to indicate placement (see
page 10 for LAG SCREW mount).
• Fixture order length is based on length between suspension points.
1
96" between suspension points
93" on uplight1 1/4" 1 1/4"
93.5" between end caps
92.5" on downlight
Based on 8' on suspension. Shop drawings required.
POWER FEED NON-FEED
2
NOTE: If feeds are on both sides of fixture, repeat feed side installation on opposite side.
SURFACE PREP
POWER FEED / NON-FEED
30
31
14
15
29
28
Length as needed
M
a
r
k
e
r
abc
4
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• Install the junction box per original manufacturer’s
instructions.
• Mount the cross bar into the junction box on non-feed side.
• Using a non-feed canopy slide the braided cables through
the cable grippers and 2 piece cable coupler, leaving the
canopy between the 2 coupler pieces.
• Screw the top part of the coupler into the crossbar’s 1/4”-20
screw from non-feed side.
• Install the junction box per original manufacturer’s
instructions.
• Feed wire from the power supply into the mounted
junction box.
• Connect supplied Wagos to the lead wire from the power
supply.
• Mount the cross bar into the junction box on feed side.
• Using a feed canopy slide the braided cables through
the cable grippers and 2 piece cable coupler, leaving the
canopy between the 2 coupler pieces.
• Screw the top part of the coupler into the crossbar’s 1/4”-20
screw from feed side.
• If fed from both ends, repeat steps above.
3
POWER FEED NON-FEED
3
Number of lead wires will vary based on light engine and control
circuit selection. See wiring diagram on page 12-13 for connection
reference.
SUSPENSION MOUNT: J-BOX
POWER FEED / NON-FEED
5
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• Mount fixture by inserting braided cable into the gripper on
the fixture. Repeat on the other side.
• Screw in the bottom piece of the couplers for both feeds, this
should pull the canopy toward the ceiling’s surface.
• Mount fixture by inserting braided cable into the gripper on
the fixture. Repeat on the other side.
• Take the power cable from the BOOM, feed through the
canopy.
• Connect to the Wago, within J-BOX.
• Number of the lead wires will vary based on light engine and
control circuit selection.
• a: Snap on the wire strain to the BOOM fixture’s lead wire
and push into the canopy.
• b: Screw in the bottom piece of the couplers for both feeds,
this should pull the canopy toward the ceiling’s surface.
4
POWER FEED NON-FEED
4
a b
SUSPENSION MOUNT: J-BOX
POWER FEED / NON-FEED
See wiring diagram on page 12-13 for connection reference.
Proceed to page 11 for finishing fixture details.
Proceed to page 11 for finishing fixture details.
Make sure the fixture is at the desired height and
is level. Allow for 2”-4” of non-stripped wire for
adjustments before trimming.
From BOOM01-SINGLE KIT
6
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• a: Pick a location on TBAR to mount TBAR-J-BOX
• b: Install the junction box per original manufacturer’s
instructions.
• Feed wire from the power supply into mounted junction box
and connect supplied Wagos to the lead wire.
• Mount the cross bar into the junction box on feed side.
• Using a feed canopy slide the braided cables through
the cable grippers and 2 piece cable coupler, leaving the
canopy between the 2 coupler pieces.
• Screw the top part of the coupler into the crossbar’s 1/4”-20
screw from feed side.
• If fed from both ends, repeat steps above.
• a: Push upward on the highlighted tab as you squeeze the
bottom tab to open up the TBAR clip.
• b: Wrap the two parts of the clip around the TBAR, then
push inward on the highlighted tab to snap them together in
place.
• Install the TBAR-non-feed per original manufacturer’s
instructions.
• Slide the braided cables through the cable grippers and 2
piece cable coupler, leaving the canopy between the 2
coupler pieces.
• Using a non-feed canopy slide the braided cables through
the cable grippers and 2 piece cable coupler, leaving the
canopy between the 2 coupler pieces.
• Screw the top part of the coupler into the crossbar’s 1/4”-20
screw from non-feed side.
POWER FEED NON-FEED
Verify the mounting location prior to
snapping on the TBAR clip, as it is
very difficult to open back up once
it has been mounted.
a ab b
33
SUSPENSION MOUNT: TBAR-J-BOX GRID
POWER FEED / NON-FEED
Number of lead wires will vary based on light engine and control
circuit selection. See wiring diagram on page 12-13 for connection
reference.
Support cable wire Support cable wire
7
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• Mount fixture by inserting braided cable into the gripper on
the fixture. Repeat on the other side.
• Screw in the bottom piece of the couplers for both feeds, this
should pull the canopy toward the ceiling’s surface.
• Mount fixture by inserting braided cable into the gripper on
the fixture. Repeat on the other side.
• Take the power cable from the BOOM, feed through the
canopy.
• Connect to the Wago, within J-BOX.
• Number of the lead wires will vary based on light engine and
control circuit selection.
• a: Snap on the wire strain to the BOOM fixture’s lead wire
and push into the canopy.
• b: Screw in the bottom piece of the couplers for both feeds,
this should pull the canopy toward the ceiling’s surface.
4
POWER FEED NON-FEED
4
a b
SUSPENSION MOUNT: TBAR-J-BOX GRID
POWER FEED / NON-FEED
Proceed to page 11 for finishing fixture details.See wiring diagram on page 12-13 for connection reference.
Proceed to page 11 for finishing fixture details.
Make sure the fixture is at the desired height and
is level. Allow for 2”-4” of non-stripped wire for
adjustments before trimming.
Support cable wire
Support cable wire
From BOOM01-SINGLE KITFrom BOOM01-SINGLE KIT
8
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• a: Pick a location on TBAR to mount TBAR-J-BOX HANGER
• b: Install the junction box per original manufacturer’s
instructions.
• Feed wire from the power supply into mounted junction box
and connect supplied Wagos to the lead wire.
• Mount the cross bar into the junction box on feed side.
• Using a feed canopy slide the braided cables through
the cable grippers and 2 piece cable coupler, leaving the
canopy between the 2 coupler pieces.
• Screw the top part of the coupler into the crossbar’s 1/4”-20
screw from feed side.
• If fed from both ends, repeat steps above.
a b
3
POWER FEED NON-FEED
3
• a: Pick a location on TBAR to mount TBAR-J-BOX HANGER
• b: Install the junction box per original manufacturer’s
instructions.
• Mount the cross bar into the junction box on non-feed side.
• Using a non-feed canopy slide the braided cables through
the cable grippers and 2 piece cable coupler, leaving the
canopy between the 2 coupler pieces.
• Screw the top part of the coupler into the crossbar’s 1/4”-20
screw from non-feed side.
a b a b
SUSPENSION MOUNT: TBAR-J-BOX HANGER
POWER FEED / NON-FEED
Number of lead wires will vary based on light engine and control
circuit selection. See wiring diagram on page 12-13 for connection
reference.
9
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
• Mount fixture by inserting braided cable into the gripper on
the fixture. Repeat on the other side.
• Screw in the bottom piece of the couplers for both feeds, this
should pull the canopy toward the ceiling’s surface.
• Mount fixture by inserting braided cable into the gripper on
the fixture. Repeat on the other side.
• Take the power cable from the BOOM, feed through the
canopy.
• Connect to the Wago, within J-BOX.
• Number of the lead wires will vary based on light engine and
control circuit selection.
• a: Snap on the wire strain to the BOOM fixture’s lead wire
and push into the canopy.
• b: Screw in the bottom piece of the couplers for both feeds,
this should pull the canopy toward the ceiling’s surface.
4
POWER FEED NON-FEED
4
a b
SUSPENSION MOUNT: TBAR-J-BOX HANGER
POWER FEED / NON-FEED
Proceed to page 11 for finishing fixture details.See wiring diagram on page 12-13 for connection reference.
Proceed to page 11 for finishing fixture details.
Make sure the fixture is at the desired height and
is level. Allow for 2”-4” of non-stripped wire for
adjustments before trimming.
From BOOM01-SINGLE KIT
10
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
SUSPENSION MOUNT: LAG SCREW
NON-FEED: cannot be used with J-BOX and TBAR installations.
3
NON-FEED NON-FEED
• Using a non-feed canopy slide the braided cables through the
cable grippers and 2 piece cable coupler, leaving the canopy
between the 2 coupler pieces.
• Mount fixture by inserting braided cable into the gripper on
the fixture. Repeat on the other side.
• Screw in the bottom piece of the couplers for both feeds, this
should pull the canopy toward the ceiling’s surface.
4
Make sure the fixture is at the desired height and
is level. Allow for 2”-4” of non-stripped wire for
adjustments before trimming.
Proceed to page 11 for finishing fixture details.
11
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE FINISHING FIXTURE WIRING DIAGRAM
SURFACE PREPFIXTURE PREP
FINISHING FIXTURE
• Adjust level before trimming excess braided cable on
non-feed side. Use Knipex Air Craft cable cutter - Not
included with shipping.
• Fixture complete.
• Adjust level before trimming excess braided cable on feed
side. Use Knipex Air Craft cable cutter - Not included with
shipping.
• Using the supplied cable stays, secure the power feed to the
suspension cable (a-c).
55
POWER FEEDPOWER FEED NON-FEED
FINISHED
Large .25"
Small .15"
0.06" Aircraft Cable
2 Conductor Wire
4 Conductor Wire
abc
POWER FEED / NON-FEED: J-BOX, TBAR-J-BOX GRID, TBAR-J-BOX-HANGER / LAG SCREW
From BOOM01-SINGLE KIT
12
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE FINISHING FIXTURE WIRING DIAGRAM
WIRING DIAGRAMS: SINGLE CONTROL
Up Light and Down Light controlled together.
Color KEY
2 Conductors 3 Conductors 4 Conductors
WT/BK C
onductors Silver
Conductors WT/BK C
onductors Silver
Conductors WT/BK C
onductors Silver
Conductors
SURFACE PREPFIXTURE PREP
NOTE: Diagrams for representation only and not to scale.
1C
POWER FEED
SUSPENSION CABLE
1C 1C
POWER FEED
QZ-192
SUSPENSION CABLE
3 or 4 conductor
POWER FEED
1C
SUSPENSION CABLE
POWER FEED
1C
SUSPENSION CABLE
1C 1C
QZ-192
POWER FEED
SUSPENSION CABLE
SUSPENSION CABLE
1C
SW, SW-HE, WD
Up/Down
1C
SW, SW-HE, WD
Up/Down
1C
RGB
Up/Down
1C
DW
Up/Down
1C (1C feed on each end from 1 power supply in the middle)
SW
Up/Down
13
INSTALLATION INSTRUCTIONS - LINEAR FIXTURE
SUSPENDED-BOOM01-SINGLE
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-30-22
METHODS / COMPONENTS
& HARDWARE
WIRING DIAGRAMS: SEPARATE CONTROL
Up Light and Down Light controlled separately.
Color KEY
2 Conductors 3 Conductors 4 Conductors
WT/BK C
onductors Silver
Conductors WT/BK C
onductors Silver
Conductors WT/BK C
onductors Silver
Conductors
SURFACE PREPFIXTURE PREP FINISHING FIXTURE WIRING DIAGRAM
NOTE: Diagrams for representation only and not to scale.
QZ-96
1C 1C
QZ-96
POWER FEED
SUSPENSION CABLE POWER FEED
QZ-96 QZ-96
1C 1C
SUSPENSION CABLE
SUSPENSION CABLE
3 or 4
conductor
POWER FEED
QZ-96 QZ-96
1C 1C
SUSPENSION CABLE
SUSPENSION CABLE POWER FEED
QZ-96 QZ-96
1C 1C
SUSPENSION CABLE
SUSPENSION CABLE
POWER FEED
QZ-96 QZ-96
1C 1C
SUSPENSION CABLE
SUSPENSION CABLE
2C
SW, SW-HE, WD
Up/Down
2C (1C feed on each end)
SW, SW-HE, WD
Up/Down
2C (1C feed on each end)
SW, SW-HE, WD Down/
RGB Up
2C (1C feed on each end) DW Up/Down
2C (1C feed on each end) RGB Up/Down
2C (1C feed on each end)
DW Down/ RGB Up or
DW Up/ RGB Down
2C (1C feed on each end)
SW, SW-HE, WD Down/
DW Up
1C 1C
QZ-96QZ-96
SUSPENSION CABLE SUSPENSION CABLE
POWER FEED
POWER FEED
QZ-96QZ-96
1C 1C
SUSPENSION CABLE SUSPENSION CABLE
/
