Q-tran Q-TRAN QOM-eLED+WD-PS LED Power Supply Installation guide

Brand
Q-tran
Model
Q-TRAN QOM-eLED+WD-PS LED Power Supply
Type
Installation guide

This manual is also suitable for

Q-Tran QOM-eLED+WD-PS LED Power Supply is a versatile and reliable power solution for your LED lighting projects. With its wide input voltage range of 120-277V, it can be used in various applications. It features 0-10V dimming capability, allowing you to adjust the brightness of your lights to create the perfect ambiance. The QOM-eLED+WD-PS is suitable for both indoor and outdoor use, making it an excellent choice for illuminating gardens, walkways, and other exterior spaces.

Q-Tran QOM-eLED+WD-PS LED Power Supply is a versatile and reliable power solution for your LED lighting projects. With its wide input voltage range of 120-277V, it can be used in various applications. It features 0-10V dimming capability, allowing you to adjust the brightness of your lights to create the perfect ambiance. The QOM-eLED+WD-PS is suitable for both indoor and outdoor use, making it an excellent choice for illuminating gardens, walkways, and other exterior spaces.

INSTALLATION LED POWER SUPPLY - QOM-eLED+WD-PS
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-12-22
Mounting Options
Housing
BOTTOM VIEW
ISOMETRIC VIEW
1.36" KNOCKOUT 4X
(FOR 1" FITTINGS)
1.07" KNOCKOUT 5X
(FOR 3/4" FITTINGS)
4.90"
14.5"
15.4"
9.22" 4.90"
NOTE: To order additional lengths of wire for connection in the secondary
Please call factory for availability.
: QOM must be installed as shown.
Pole Mount
Surface Wall Mount
2.00"
0.25"
1/4”x2” wood screw or
LAG bolt recommened
1.82"
3.38"
3.14"
INSTALLATION LED POWER SUPPLY - QOM-eLED+WD-PS
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-12-22
Wiring Installation
Input Load
NEU HOT GND
0 - 10V
DIM-MOD
0-10V
Output Load Output Load 0-10V
0 - 10V
DIM-MOD
0 - 10V
DIM-MOD
0 - 10V
DIM-MOD
0 - 10V DIM-MOD
R
D
B
L
R
D
B
L
R
D
B
L
R
D
B
L
LED DRIVER (120 - 277V) LED DRIVER (120 - 277V)
0 - 10V
DIM-MOD
Warm-Dim
Module
LED DRIVER (120 - 277V)
iQ-LED
0-10V
NEU HOT GND
+24V Cool
RTN
Warm
RTN
QOM-eLED+WD
: for exterior
SECONDARY
PRIMARY
+24V
CW
HOT
NEU
0-10V
DIMMING*
GND
INSTALLATION LED POWER SUPPLY - QOM-eLED+WD-PS
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-12-22
Swimming Pool Installation
Fundamental Construction
REGULATIONS
In accordance with the requirements of NEC680 regulation in the United States, when an illumination light is installed in the swimming pool, the distance from the bottom of
the terminal box to the ground shall be no less than 4 inches. The vertical distance to the water surface of the swimming shall not be less than 8 inches, and the horizontal
distance to the water edge of the swimming pool shall not be less than 48 inches.
REQUIREMENT FOR POWER SUPPY
Please use only an isolating low voltage power supply with ungrounded output, evaluated for swimming pool use.
All the fundamental constructions, including the installation of junction box and switch, cable bushing and laying, the digging of slots, etc.,
should be done before the light installation.
Pool Spa Waterproof Junction Box
Corrosion
Resistant Conduit
8 in. Min. Bottom of
J-box to Top of Water Lin
e
48 in. Min. J-Box
to Edge of Pool
Seal Conduit Entry with
Pool-grade Silicone Sealant
To Class 2 LED Driver,
GFCI, &Circuit Breaker
4 in. Min.
For swimming pool, the embedded installation is strongly suggested so as to secure the swimmers'
safety and avoid the damage to lights, so a slot for implanting profiles should be prepared on mountin
g
surface first, suggested slot sizes: 0.95” in width, 0.98” in depth.
0.98”
0.95”
INSTALLATION LED POWER SUPPLY - QOM-eLED+WD-PS
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-07-12-22
CSA Requirements
• Power unit for use with Fountain, Swimming Pool, and Spa Luminaires
• Suitable for indoor and outdoor use
• This power supply must be installed according to the National Electric Code and local codes and ordinances and in
accordance with applicable installation code by a person familiar with the construction and operation of the product and
the hazards involved.
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
• To avoid a hazard to children, account for all parts and destroy all packaging materials.
• Keep enclosure cover covered.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Q-tran Q-TRAN QOM-eLED+WD-PS LED Power Supply Installation guide

Brand
Q-tran
Model
Q-TRAN QOM-eLED+WD-PS LED Power Supply
Type
Installation guide
This manual is also suitable for

Q-Tran QOM-eLED+WD-PS LED Power Supply is a versatile and reliable power solution for your LED lighting projects. With its wide input voltage range of 120-277V, it can be used in various applications. It features 0-10V dimming capability, allowing you to adjust the brightness of your lights to create the perfect ambiance. The QOM-eLED+WD-PS is suitable for both indoor and outdoor use, making it an excellent choice for illuminating gardens, walkways, and other exterior spaces.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents