Deagostini Fiat 126p User guide

  • Hello! I have reviewed the assembly guide for the model car Fiat 126p and the caravan. This document provides a detailed breakdown of the assembly process, from installing the ceiling lining and headlights to attaching the inner body panels. I'm ready to help with any questions you have regarding the assembly process outlined in this guide.
  • What parts are included in Stage 81?
    How are the headlights secured in Stage 82?
    What is the purpose of the fuse box in Stage 83?
    How are the inner body panels attached in Stages 84 and 85?
    What type of screws are used to fix front inner caravan wall?
    How many stickers included in set?
PackPack
1717
STAGE PAGE
81 Ceiling lining 275
82 The headlights 278
83 The fuse box 281
84 Left rear inner body panel 284
85 Right rear inner body panel 287
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2020
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
275
Your parts:
81A. Ceiling lining
81B. Interior light
81C. Caravan reector holder
81D. Caravan reector
81E. Stickers
NP. 2 x 2.5 x 5mm screws
CP. 1.7 x 4mm screws
EM. 2 x 3mm screws
Stage 81: Ceiling lining
276
2Turn the parts over and secure with four NP screws.
1 Connect the ceiling lining (81A) to the roof inner (78A), inserting
the posts into the corresponding holes.
4 Run the cable along the groove in the roof inner.
3Prepare the interior light (81B) and gently bend the wire just
under the LED bulb to a 90–degree angle.
6 Remove the crossbars from the bottom of the body.
5Secure the cable with three stickers (81E), as shown.
277
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
7Place the roof inner inside the body, aligning the holes of both.
When in position, secure with four EM screws.
278
Your parts:
82A. Headlights
82B. Tabs
82C. Caravan reector holder
82D. Caravan reector
AM. 1.7 x 3mm screws
CP. 1.7 x 4mm screws
Stage 82: The headlights
279
2Position the cable as shown and place the two tabs over it,
aligning them with the holes in the panel, as shown.
1Insert the headlights (82A) into the housings in the front panel.
3Secure with two AM screws. 4Now combine the caravan reflectors (81D and 82D) with the
holders (81C and 82C)
280
6Secure the holders from inside the caravan with two CP screws.
5Insert the backs of the holders into the two indicated holes in the
front of the caravan
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
281
Your parts:
83A. Fuse box
83B. Boot lid lock
83C. Caravan front lights
AP. 1.7 x 3mm screws
BM. 2 x 4mm screws
IP. 2 x 4mm screws
Stage 83: The fuse box
282
2Secure from underneath with two IP screws.
1 Place the fuse box (83A) on the left side of the body. Insert the
pin into the centre hole.
3Place the boot lid lock (83B) into the indicated position on the
body. Align the holes of both parts. 4Secure the lock with two BM screws.
283
6Secure the lights from the inside with two AP screws.
5Install the caravan front lights (83C) in the indicated positions in
the front wall.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
284
Your parts:
84A. Left rear inner body panel
84B. Caravan front light lenses
CM. 2.3 x 4mm screws
Stage 84: Left rear inner body panel
285
2Make sure that the lighting cable doesn’t get pinched between
the two parts. Then secure the panel with a CM screw.
1Turn the body over and align the left rear inner body panel (84A)
with the inside of the body. Match the screw holes to each other.
3Mount one of the caravan front light lenses (84B) into one of
the lights. 4Fix the second lens into place.
286
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
287
Your parts:
85A. Right rear inner body panel
85B. Front inner caravan wall
CM. 2.3 x 4mm screws
IP. 2 x 4mm screws
Stage 85: Right rear inner body panel
288
2Secure the panel with a CM screw.
1Install the right rear inner body panel (85A) on the inside of the
body, in the same way as the left panel.
3Now mount the front inner caravan wall (85B) on the inside of
the outer wall, aligning the holes of both parts. 4Fix the front wall in position with four IP screws.
289
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
/