Deagostini Fiat 126p User guide

PackPack

1212

STAGE PAGE

56 Right front seat 190

57 Right front seat 193

58 Right front seat back 196

59 Caravan roof screen 199

60 The dashboard 202

Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.

Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.

Warning: Not suitable for children under the age of 14.

is product is not a toy and is not designed or intended for use in play.

Items may vary from those shown.

190

Your parts:

56A. Right front seat frame

56B. Right front seat cover

56C. Sponge

56D. Roof cover right front hinge

CP. 1.7 x 4mm screws

GP. 1.5 x 7mm screws

Stage 56: Right front seat

191

4Place the right front seat cover (56B) onto the seat assembly,

lifting the tabs of the cover over the base.

5Secure the cover from underneath with four CP screws. 6Place the roof cover right front hinge (56D) into the mount.

2 Secure the frame with two CP screws.

1Insert the right front seat frame (56A) into the corresponding

holes in the underside of the seat base.

3Place the sponge (56C) onto the top of the seat.

192

7 Secure with a GP screw.

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

193

Your parts:

57A. Right front seat base

57B. Right front seat back mount

57C. Caravan roof screen frame

NM. 2 x 6mm screws

Stage 57: Right front seat

194

2 Secure one side of the frame with an NM screw.

1 Place the front seat base frame (57A) onto the seat side frames, aligning the holes of both.

3 Fix the other side of the frame with another NM screw.

195

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

196

Your parts:

58A. Right front seat back

58B. Caravan roof screen 1

IP. 2 x 4mm screws

OM. 1.7 x 6mm screws

LP. 1.2 x 3mm screws

PM. 2 x 3 x 6mm screws

Stage 58: Right front seat back

197

2Fit the seat back into the rear of the seat, aligning the holes of

the mounts with those in the frames of the seat.

1Fix the two right front seat back mounts (57B) to the holes at the

bottom of the seat back with two IP screws.

3Secure the two parts of the seat together on one side with

an OM screw. 4 Fix the parts in place with a second screw (OM) from the other

side of the seat as shown in the picture.

198

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

5 Place the posts on the bottom of the right front seat into the

slots in the floor, as indicated. 6 Hold the seat in place and secure into position from underneath

the floor with two PM screws.

199

Your parts:

59A. Lower steering column housing

59B. Upper steering column housing

59C. Caravan roof screen 2

BM. 2 x 4mm screws,

LP. 1.2 x 3mm screws, 6 + 3 pieces

Stage 59: Caravan roof screen

200

2 Fasten the pieces together with a BM screw.

1 Connect the lower steering column housing (59A) to

the upper (59B).

3Prepare the roof parts supplied with Stages 57 and 58.

Place caravan roof screen 1 (58B) onto the caravan roof screen

frame (57C).

4 Secure the screen to the frame with six LP screws. Carefully

tighten the screws one by one to avoid damaging the screen.

201

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

5Place caravan roof screen 2 (59C) onto the screen frame. 6Carefully secure the screen with six LP screws.

202

Your parts:

60A. Dashboard

60B. Left vent housing

60C. Right vent housing

60D. Caravan roof panel

IP. 2 x 4mm screws

AP. 1.7 x 3mm screws

CP. 1.7 x 4mm screws

Stage 60: The dashboard

203

2Secure the steering column housing assembly (Stage 59) to the

dashboard with two IP screws.

1Align the pins of the left and right vent housings (60B and 60C)

with the matching holes in the recesses of the dashboard (60A).

3Place the dashboard onto the front bulkhead (Stage 54), as

shown, and secure in place with three CP screws. 4 Place the caravan roof cover into the opening in the top of

the caravan roof panel (60D). Be careful with the hinges when

fitting the cover. Lift them into their corresponding notches (inset).

204

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

5Place the roof screen frame onto the inside of the roof panel,

over the cover, aligning the holes of both. 6Secure the roof screen frame to the panel with eight AP screws.

Deagostini Fiat 126p User guide

Deagostini Fiat 126p User guide

Related papers

Other documents