Deagostini Fiat 126p User guide

Type
User guide
PackPack
2424
STAGE PAGE
120 Rear windows 406
121 Rear window 409
122 Caravan trunk 412
123 Caravan chassis 415
124 Roof rack bars 418
125 Fitting the caravan 421
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2020
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
406
Your parts:
120A. Left rear window
120B. Right rear window
120C. Caravan leg hinge
120D. Caravan leg
120E. Caravan leg support
120F. Adhesive tape
NM. 2 x 6mm screws
AM. 1.7 x 3mm screws
KM. 2 x 5mm screws
Stage 120: Rear windows
407
3Apply adhesive tape around the edge of the right window
opening and remove the backing from them. 4Press the right window into the opening.
5Insert the end of the caravan leg (120D) into the space in the
hinge (120C). Secure in place with an NM screw. 6Place the hinge onto the caravan chassis and fix in place with
an AM screw.
2 Prepare the left rear window (120A). Note that the outer black
frame of both rear windows (120A and 120B) is slightly convex.
The glass can therefore only be installed in one position. Align the
left window with the corresponding opening, and press into place.
1Apply four pieces of adhesive tape (120F) around the edge of the
left rear window opening. Then remove the backing.
408
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
7Fix the caravan leg support (120E) over the rounded end of the
leg with a KM screw.
409
Your parts:
121A. Rear window
121B. Caravan leg
121C. Caravan leg hinge
121D. Caravan leg support
121E. Adhesive tape
NM. 2 x 6mm screws
AM. 1.7 x 3mm screws
KM. 2 x 5mm screws
Stage 121: Rear window
410
2Align the rear window (121A) with the opening and press
into place.
1 Prepare six pieces of adhesive tape. Affix them around the rear
window opening. Peel off the backing.
3Place the end of the caravan leg (121B)into the hinge (121C).
Secure in place with an NM screw. 4Fix the hinge to the caravan chassis with an AM screw.
411
5Secure the caravan leg support (121D) over the curved part of
the leg with a KM screw.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
412
Your parts:
122A. Roof rack supports
122B. Caravan trunk
122C. Caravan trunk lid
BM. 2 x 4mm screws
UM. 1.5 x 3mm screws
DP. 1.7 x 5mm screws
CP. 1.7 x 4mm screws
Stage 122: Caravan trunk
413
3Secure the other ends of the supports with two more UM screws. 4Place the trunk lid (122C) onto the trunk (122B) and align the
holes of both parts. Secure together with two DP screws.
5Insert the posts on the bottom of the trunk into the corresponding
holes in the drawbar. 6Secure the trunk to the drawbar with two CP screws.
2Fix the supports to one side of the roof with two UM screws.
1 Place the roof rack supports (122A) onto the roof of the car and
align the holes at the ends of them with the corresponding holes
in the roof.
414
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
7 Fix the drawbar to the caravan frame with five BM screws.
415
Your parts:
123A. Roof rack frame
123B. Caravan front bumper
UM. 1.5 x 3mm screws
DP. 1.7 x 5mm screws
PP. 2 x 5mm screws
Stage 123: Caravan chassis
416
2Tighten two more UM screws into the holes on the left side.
1Place the roof rack frame (123A) onto the supports (122A),
aligning the holes of both. Tighten two UM screws into the
holes on the right side.
3Turn the caravan over and install the front bumper (123B), as
shown. Align the holes of both parts. 4Secure the bumper with four FP screws.
417
6Secure the frame with four PP screws, as shown.
5 Align the caravan frame with the caravan floor. Pass the rear light
cable through the drawbar.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
418
Your parts:
124A. Roof rack bars
124B. Caravan rear bumper
DP. 1.7 x 5mm screws
AM. 1.7 x 3mm screws
Stage 124: Roof rack bars
419
2Fit the caravan rear bumper (124B) into the space at the rear of
the caravan, as shown.
1 Press the pins on the five roof rack bars (124A) into the
corresponding holes in the supports.
3Secure the bumper with four DP screws. 4Route the lighting cable along the drawbar, as shown. Secure
the cable in place with a fastener (116F) and an AM screw.
420
5 Use the second fastener (116F) and another AM screw to fix the
cable in position further along the drawbar.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
421
Your parts:
125A. Outer wheel
125B. Inner wheel
125C. Valve
125D. Tyre
125E. Caravan front stands
125F. Caravan rear stands
DM. 2 x 3 x 5mm screws
Stage 125: Fitting the caravan
422
3Place the front stands (74A) under the car, behind the front
wheels, and the rear stands (74B) in front of the rear wheels. 4Connect the cars tow bar to the caravans drawbar.
5Adjust the position of the drawbar handle until the holes of
both bars are aligned. Then pass the pin at the end of the chain
through the aligned holes.
6Connect the caravan light cable to the end of the cable from
the car, as shown.
2Open the car bonnet and fit the spare wheel into the space in
the middle.
1Assemble the spare wheel parts as with previous wheels.
423
Congratulations! You have completed your assembly of the Fiat 126p with caravan.
7Open the bonnet and activate the vehicles control button. You
should now re-test the electrical system (see Stage 114). 8 Check that the caravans rear lights are working. Press the brake
pedal in the car to illuminate them.
9Place the caravan stands either side of the wheels, as shown.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Deagostini Fiat 126p User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI