PackPack
1515
STAGE PAGE
71 Throttle lever 241
72 The battery box 244
73 Fitting the interior 247
74 Caravan rear reectors 250
75 The body 253
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2020
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
241
Your parts:
71A. Throttle lever
71B. Throttle lever mounting
71C. Ventilation diuser
71d. Rear inner caravan wall
CP. 1.7 x 4mm screws
IP. 2 x 4mm screws
BM. 2 x 4mm screws
Stage 71: Throttle lever
242
2Connect the throttle lever (71A) to the throttle lever mount (71B)
with a CP screw, as shown.
1Inset the ventilation diffuser (71C) into the hole in the boot floor
(Stage 70). Secure with a CP screw
4Remove the screw from the fan cover.
3Remove the screws holding the engine cover in position.
Store screws in a safe place.
6 Fix the throttle lever in place with an IP screw.
5Place the throttle lever over the fan cover, aligning the holes
of both.
243
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
7Refit the engine cover place. 8 Mount the rear inner part of the trailer window (71D) horizontally
on the rear window of the trailer (part E from number 67). Secure
the assembly with two screws (IP).
244
Your parts:
72A. Battery box
72B. Curtain (2 pcs.)
72C. Curtain rod (2 pcs.)
BM. 2 x 4mm screws
Stage 72: The battery box
245
2Secure the battery box with three BM screws.
1Place the battery box (72A) over the opening in the boot floor
(Stage 70).
3Place the curtains (72B) onto the curtain rod (72C). 4Pass the second curtain rod through the lower channels in
the curtains.
246
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
5 Insert the ends of the curtain rods into the holes in the rear
wall (71D).
247
Your parts:
73A. Battery cover
73B. Switch mount
73C. Caravan rear light lenses (2 pcs.)
73D. Caravan rear light mounts
EM. 2 x 3mm screws
BM. 2 x 4mm screws
JP. 2.3 x 5mm screws
Stage 73: Fitting the interior
248
3 Secure the boot in place from underneath with two BM screws. 4Place the interior above the chassis and collect the wires
coming from it.
5Connect the three wires coming from the interior to the
corresponding wires from the chassis. 6Then connect the red-black wires (battery box) and the double
black wires (brake pedal).
2 Place the boot onto the bulkhead.
1 Fix the switch mount (73B) to the underside of the boot with two
EM screws.
249
Here is how your assembly should look at the end of this
stage. Keep any assemblies, unused parts and spares labelled
to one side for later use.
9Place two AAA batteries into the battery box. Place the cover
(73A) into the top of the box.
11Insert the caravan rear light lenses (73C) into the mounts (73D).
Make sure that the orange ends are outermost. 12Fit the caravan rear lights to the lower rear caravan wall
from the inside, pressing the holes onto the posts.
8 Turn the model over and fix the floor to the chassis with four
JP screws.
7Lower the interior onto the chassis, moving all unconnected
wires to the left side of the vehicle.
10To check if you have connected the cables correctly, press the
battery power switch. The speedometer should illuminate.
Press function button 2 (64A), you should hear the sound of the engine
running. Press the function button 1 (63A) to sound the horn.
* Due to design reasons, the functions of the dashboard buttons of the model do not coincide with the functions of the corresponding buttons in the full-size car.
2 x AAA BATTERIES
250
Your parts:
74A. Front stands
74B. Rear stands
74C. Rear caravan reectors
74D. Rear caravan lights
Stage 74: Caravan rear reectors
251
2Fit the second reflector in the same way on the other side.
1 Insert one of the caravan rear reflectors (74C) into the three
corresponding holes in the caravan rear wall, as shown.
3Gently insert the caravan rear lights (74D) into the
light mounts. 4Place the front and rear stands (74A and 74B) underneath
the chassis, between the front and rear wheels. .
252
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
253
Your parts:
75A. Body
75B. Interior light switch
Stage 75: The body
254
2Feed the end of the switch through the hole and insert it into the
recess in the body, as shown.
1 Insert the end of the interior light switch (75B) into the indicated
hole in the body (75A), from the inside.
3Insert the other end of the interior light switch into the
corresponding hole on the other side of the body, as shown. 4Fit the switch into the recess in the body.
255
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
/
