Page is loading ...
PackPack
2121
STAGE PAGE
102 Caravan table 346
103 Caravan crockery 349
104 Left door 352
105 Left wing mirror 355
106 Left door hinge 358
107 Left door 361
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2020
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
346
Your parts:
102A. Seatbelts
102B. Caravan table
LP. 1.2 x 3mm screws
Stage 102: Caravan table
347
2Secure the seat belt with an LP screw.
1Take one of the seat belts (102A) and put the rounded end over
the indicated hole on the inside of the body. Make sure the
adjuster is facing inwards.
3Take the second seat belt and place the rounded end over the
indicated hole on the inside of the body. The adjuster should be
facing inwards.
4Secure the belt with a second LP screw.
348
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
349
Stage 103: Caravan crockery
Your parts:
103A. Left air intake grille
103B. Right air intake grille
103C. Table legs
103D. Cable clamps
103E. Large plate
103F. Medium plate
103G. Small plate
103H. Large cup
103I. Small cup
CP. 1.7 x 4mm screws
IP. 1.7 x 5mm screws
PP. 2 x 5mm screws
350
3Place the caravan table (102B) upside down on a flat surface.
Place the table legs (103C) over the indicated holes in the table,
as shown. Secure in place with two IP screws.
4Insert the ends of the table legs into the holes in the centre of the
caravan floor.
5Secure the table legs with two IP screws from the underside of
the floor. 6Arrange the crockery on the table in the order and position shown.
They have magnets in them that will fix them in place.
2 Fit the right air intake grille (103B) into the hole shown in the
right side of the body.
1Push the left air intake grille (103A) into the indicated hole in
left side of the body.
351
7 Finally place the flower pot (90D) on the table, as shown.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
352
Your parts:
104A. Left door
104B. Left door handle cover
104C. Left door handle
104D. Left door lock
104E. Internal lock
104F. Caravan frame
104G. Window protection 1
104H. Window protection 2
MM. 1.7 x 3mm screws
SP. 1.7 x 5mm screws
Stage 104: Left door
353
3 Secure the left door handle cover with two SP screws from the
inside of the door. 4Fix the internal lock (104E) to the inside of the door with an
MM screw.
5Secure the left door lock to the inside of the handle with two
SP screws. 6Fix the window protection 1 strip (104G) along the bottom edge
of the window opening. Remove the backing paper to affix.
2 Place the left door handle cover (104B) over the handle.
1Fit the left door handle (104C) into the opening in the left door
(104A), as shown.
354
7 Remove the backing paper from one of the window protection 2
strips (104H) and fix over the raised part shown on the inside of
the left door.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
8Remove the backing paper and fix the second window protection 2
strip (104H) to the other raised part of the door, as shown.
355
Your parts:
105A. Wing mirror arm
105B. Wing mirror housing
105C. Wing mirror
105D. Caravan suspension frame
105E. Pot
105F. Pot lid
105G. Choke and starter lever housing
105H. Choke and starter levers
AP. 1.7 x 3mm screws
HP. 1.5 x 3mm screws
CP. 1.7 x 4mm screws
PP. 1.7 x 4mm screws
Stage 105: Left wing mirror
356
3Insert the end of the arm into the hole in the front of the door
and secure with an AP screw. 4Place the choke and starter levers (105H) into the housing
(105G), as shown.
5Place the lever housing onto the central console. Secure in place
with some cyanoacrylate glue. 6Place the pot lid (105F) into the top of the pot (105E).
2 Remove the backing from the wing mirror (105C) and fit it into
the housing.
1Fix the wing mirror arm (105A) to the mirror housing (105B) with
a HP screw.
Glue
357
7 Place the pot onto the caravan table.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
9 Turn the caravan over and secure the floor to the body with eight
PP screws. 10Lead the cable from the rear of the caravan to the front
and secure at the indicated points with the cable clamps
(103D) and CP screws.
8 Carefully place the caravan body over the floor, aligning the
corresponding holes of both pieces.
358
Your parts:
106A. Left door hinge plate
106B. Left door hinge
106C. Caravan suspension bar
106D. Caravan suspension bar hinge
106E. Spring
BM. 2 x 4mm screws
JM 2.3 x 3 x 5mm screws
PM. 2 x 3 x 6mm screws
Stage 106: Left door hinge
359
3Secure the left door hinge plate with a JM screw. 4Lay the caravan frame (104F) in front of you. Insert the caravan
suspension bar hinge (106D) into the indicated hole in the
bottom of the frame.
5Turn the frame over and secure the hinge with a BM screw. 6Turn the frame over again. Slide the spring (106E) onto the
suspension bar (106C), as shown and then into the large hole in the
frame. Place the other end of the bar into the corresponding grooves in
the centre of the top of the frame.
2 Place the left door plate (106A) over the hinge, as shown, aligning
the corresponding holes.
1Place the left door hinge (106B) into the indicated position on the
inside of the left door.
360
7 Secure the bar from the top of the frame with a PM screw.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
361
Stage 107: Left door
Your parts:
107A. Left door inner
107B. Left door panel
107C. Left door compartment
107D. Caravan suspension bar
107E. Caravan suspension bar hinge
107F. Spring
107G. Window protection
FP. 2 x 3mm screws
IP. 2 x 4mm screws
CP. Screws 1.7 x 4mm screws
BM. 2 x 4mm screws
CM 2.3 x 4mm screws
PM. 2 x 3 x 6mm screws
362
3Remove the two circular pieces from the window protection
(107G) and affix them to the outside of the door inner at the
bottom of the window opening (see Step 5).
4Insert the posts of the left door compartment (107C) into the
indicated holes in the panel.
5Secure the compartment with two CP screws. 6Insert the caravan suspension bar hinge (107D) into the indicated
hole in the caravan frame and secure with a BM screw from the
top of the frame.
2Secure the panel from the outside of the door inner with the IP
and FP screws.
1Place the left door panel (107B) into the recess in the left door
inner (107A).
363
7Slide the spring (107F) onto the suspension bar (107D), as shown
and then into the large hole in the frame. Place the other end of
the bar into the corresponding grooves in the centre of the top of the
frame. Secure the bar from the top of the frame with a PM screw.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
9Secure the frame with three CM screws.
8 Place the suspension bar frame (105D) over the ends of the
suspension bars in the centre of the frame.
/
