Deagostini Fiat 126p User guide

PackPack

99

STAGE PAGE

41 Centre console 139

42 Gear lever 142

43 Left rear interior side 145

44 Right rear interior side 148

45 Rear seat 151

Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.

Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.

Warning: Not suitable for children under the age of 14.

is product is not a toy and is not designed or intended for use in play.

Items may vary from those shown.

139

Stage 41: Centre console

Your parts:

41A. Centre console upper

41B. Centre console lower

41C. Handbrake lever

41D. Reector housings

CP. 1.7 x 4mm screws

EP. 1.7 x 2.5 washer screws

140

2 Turn the centre console upper over and insert the three posts into

the corresponding holes in the centre console lower (41B)

1Pass the handbrake lever (41C) through the slot at the front of the

centre console upper (41A).The lever can only fit in one position.

4Place the centre console over the space in the middle of the floor,

between the seatbelt holders.

3 Secure the parts together with three CP screws from inside the

centre console lower.

6Insert the two reflector housings (41D) into the two corresponding

holes in the caravan right wall (40H).

5Fix the centre console to the floor with two CP screws

from underneath.

141

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

7 Secure the reflector housings to the caravan wall with two EP

screws from the inside.

142

Stage 42: Gear lever

Your parts:

42A. Gear lever base

42B. Gear lever

42C. Gear lever base bracket

42D. Gear lever knob

42E. Heater lever

42F. Right caravan window

CP. 1.7 x 4mm screws

EP. 1.7 x 2.5mm washer screws

143

2 Pass the assembly up through the large circular hole in the

centre console, aligning the matching holes of both parts.

1 Pass the gear lever (42B) up through the holder (42A) and into

the hole in the knob (42D).

4 Insert the heater lever (42E) into the hole at the front of the

centre console.

3 Place the gear lever base bracket (42C) over the bottom of the

base and secure with two CP screws.

6Secure the window with four EP screws.

5Place the holes in the four tabs around the caravan window

(42F) over the posts around the window opening in the

caravan right wall.

144

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

145

Your parts:

43A. Left rear interior side

43B. Reectors

IP. 2 x 4mm screws

Stage 43: Left rear interior side

146

2 Secure the left rear interior side from underneath with two

IP screws.

1Insert the three posts on the bottom of the left rear interior

side (43A) into the corresponding holes in the left side of the

interior floor.

3Place the first reflector (43B) into one of the reflector housings

in the right caravan wall. 4Fit the second reflector (43B) in the same way to the other

housing in the right wall.

147

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

148

Stage 44: Right rear interior side

Your parts:

44A. Right rear interior side

44B. Exterior of the front door

IP. 2 x 4mm screws

149

2 Hold the part in place and secure from the underside with two

IP screws.

1 Insert the posts on the bottom of the right rear interior side (44A)

into the corresponding holes in the right side of the interior floor.

150

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

151

Your parts:

45A. Rear seat base

45B. Rear seat cover

45C. Sponge

45D. Caravan door vent

FP. 2 x 3mm screws

IP. 2 x 4mm screws

BP. 1.5 x 4mm screws

Stage 45: Rear seat

152

2 Take the rear seat base (45A) and place it under the tabs of the

rear seat cover (see next step).

1 Insert the sponge (45C) into the rear seat cover (45B), making

sure all the sides line up properly.

3Align the hole in the cover tabs with those in the base and

tighten an EP screw into each. 4Place the rear seat between the two rear interior sides,

inserting the posts into the holes.

153

6Mount the caravan door vent (45D) to the outside of the caravan

door using four BP screws. 5 Secure the seat from underneath with two IP screws.

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

Deagostini Fiat 126p User guide

Deagostini Fiat 126p User guide

Related papers

Other documents