Edsal 1YCA1 Assembly Manual

Edsal
Brand
Edsal
Model
1YCA1
Type
Assembly Manual

This manual is also suitable for

Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety
hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not use this unit for
anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR USE IT AS A LADDER.
Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care when working with metal parts.
Instruction Manual
Heavy Duty 1 Drawer Work Bench
MODEL NUMBER
WB2448 - WB2460 - WB3060 -
1YBZ9 - 1YCA1 - 1YCA2
WB2448
WB2448
WB2448
-
-
-
1YBZ9
1YBZ9
1YBZ9
-
-
-
1 Drawer
1 Drawer
1 Drawer
-
-
-
60”h x 24”d x 48”w
60”h x 24”d x 48”w
60”h x 24”d x 48”w
Description
Long Post
Brace
Beam
Short Post
Top Shelf Support
Shelf Support
Drawer Mount
Drawer Slide
Drawer Shelf Braces
Peg Board
Peg Board Bracket
Bottom Wood Shelf
Top Wood Shelf
Wood Drawer Shelf
Wood Top Shelf
Post Coupler
Hardware
Qty.
4
4
5
2
1
2
2
2
2
1
2
1
1
1
1
2
16
Part Number
RUPT3602
RWBE2303
RWBE4703
RUPT2402
RWSS4803
RWSB2801
RWDM2305
RWDS2003
RWDB4303
PGBD4820
RWPB0401
RLPB2448
MDF2448
RPB43017
RPB2489
RMPC0403
NB16
Part Size
36”
24”
48”
24”
48”
N/A
N/A
N/A
43”
20” x 48”
4 3/4” x 1”
24” x 48”
24” x 48”
17” x 43”
9” x 48”
4”
#10-24
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams
and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer
head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal manufacturing facility at,
(773) 475-3000 and request customer service. We can also be reached on the internet at the following email address :
[email protected].
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
WB2460
WB2460
WB2460
-
-
-
1YCA1
1YCA1
1YCA1
-
-
-
1 Drawer
1 Drawer
1 Drawer
-
-
-
60”h x 24”d x 60”w
60”h x 24”d x 60”w
60”h x 24”d x 60”w
Description
Long Post
Brace
Beam
Short Post
Top Shelf Support
Shelf Support
Drawer Mount
Drawer Slide
Drawer Shelf Braces
Peg Board
Peg Board Bracket
Bottom Wood Shelf
Top Wood Shelf
Wood Drawer Shelf
Wood Top Shelf
Post Coupler
Hardware
Qty.
4
4
5
2
1
2
2
2
2
1
2
1
1
1
1
2
16
Part Number
RUPT3602
RWBE2303
RWBE5903
RUPT2402
RWSS6003
RWSB2801
RWDM2305
RWDS2003
RWDB5503
PGBD6020
RWPB0401
RLPB2460
MDF2460
RPB55017
RPB2609
RMPC0403
NB16
Part Size
36”
24”
60”
24”
60”
N/A
N/A
N/A
55”
20” x 60”
4 3/4” x 1”
24” x 60”
24” x 60”
17” x 55”
9” x 60”
4”
#10-24
WB3060
WB3060
WB3060
-
-
-
1YCA2
1YCA2
1YCA2
-
-
-
1 Drawer
1 Drawer
1 Drawer
-
-
-
60”h x 30”d x 60”w
60”h x 30”d x 60”w
60”h x 30”d x 60”w
Description
Long Post
Brace
Beam
Short Post
Top Shelf Support
Shelf Support
Drawer Mount
Drawer Slide
Drawer Shelf Braces
Peg Board
Peg Board Bracket
Bottom Wood Shelf
Top Wood Shelf
Wood Drawer Shelf
Wood Top Shelf
Post Coupler
Hardware
Qty.
4
4
5
2
1
2
2
2
2
1
2
1
1
1
1
2
16
Part Number
RUPT3602
RWBE2903
RWBE5903
RUPT2402
RWSS6003
RWSB2901
RWDM2305
RWDS2003
RWDB5503
PGBD6020
RWPB0401
RLPB3060
MDF3060
RPB55017
RPB2609
RMPC0403
NB16
Part Size
36”
30”
60”
24”
60”
N/A
N/A
N/A
55”
20” x 60”
4 3/4” x 1”
30” x 60”
30” x 60”
17” x 55”
9” x 60”
4”
#10-24
Start by taking one (1) 24” short post, one (1) 36” long
post, and one (1) post coupler, and join the two post to-
gether to create the back post. Take one (1) brace with
the shelf ledge facing up, and one (1) long 36” post and
attach the rivets of the brace to the top two (2) holes of
the 36” long post. Take the back post and attach the op-
posite rivets of the brace to the holes of the back post so
the brace is level. Tap brace down to seat. Attach the
bottom brace to the front 36” post skipping one (1) hole
from the bottom and the opposite end to the back post,
tap brace down to seat. Take one (1) drawer mount and
skip one (1) hole from the top brace and attach rivets
to the short and long post, tap down to seat. Take one
(1) drawer slide and insert it into the slide of the drawer
mount. Repeat steps for the opposite end assembly.
Assembly Instructions for Heavy Duty 1 Drawer Work Bench
Assembly Instructions for Heavy Duty 1 Drawer Work Bench
Assembly Instructions for Heavy Duty 1 Drawer Work Bench
Take four (4) beams with the bend facing up, and at-
tach the rivets even with the braces from the two end
assembly's, and tap down to seat. Install the top shelf
support by installing the rivets to the back post using the
top two (2) holes. Install one (1) beam with the bend
facing down, to the top holes of the back posts, even
with the rivets from the top shelf. Next install a peg
board bracket to the back beam of the top assembly us-
ing the nuts and bolts provided. Add the final peg board
brackets and one (1) shelf support to the top two (2)
beams using the nuts and bolts provided. Add the final
shelf support to the bottom two (2) beams using the nuts
and bolts provided.
Place the peg board to the inside of the back post of the work
bench. Align the holes of the peg board to the holes on the
back post, and fasten using the nuts and bolts provided.
Align the holes on the peg board brackets to the holes of the
peg board, and fasten the peg board to the peg board brack-
ets using the nuts and bolts provided. Take the two (2)
drawer shelf braces and with the shelf ledge facing down,
insert the two (2) rivets into the two (2) holes located on the
drawer slides, for the front and back of the drawer.
Add the wood shelves to the top shelf support, the draw-
ers, the bottom shelf, and the work surface to finalize the
assembly of the workbench.
Step
1
Step
2
Step
3
Step
4
Drawer Mount
Drawer Slide
Long Post
Front 36” Long Post
Short Post
Back Post Assembly
24” Brace
Top Shelf Support
Beam
(Bend facing down)
Beams
(back side also)
Peg Board Bracket
Shelf Support
Post
Coupler
Long Post
(Top 36”)
Short Post
(Bottom 24”)
Peg Board
Drawer Shelf Braces
(Bend facing down)
(Back side also)
Shelf Ledge Up
Skip Hole
From Bottom
Tap Lightly
  • Page 1 1
  • Page 2 2

Edsal 1YCA1 Assembly Manual

Edsal
Brand
Edsal
Model
1YCA1
Type
Assembly Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents