Edsal MRWB52COS Assembly Manual

Brand: Edsal

Model: MRWB52COS

Type: Assembly Manual

Safety Instructions

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a

possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not

included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY

PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the

heavier loads on the bottom. Use care when working with metal parts.

Heavy Duty 5’

Work Bench

MODEL NUMBER

MRWB52COS

MRWB52COS 3 Shelf 2 Drawer

60”h x 24”d x 60”w

Description

Long Post

Brace

Beam

Short Post

Shelf Support

Top Shelf Beam

Drawer Mount

Drawer Slide

Drawer Shelf Brace

Peg Board

Bottom Wood Shelf

Center Bracket

Center Drawer Mount

Peg Board Bracket

Drawer Wood Shelf

Top Wood Shelf

Work Surface Top

Hardware

Light Fixture

Qty.

Part Number

RUPT6002

RWBE2303

RWBE6003

RUPT3602

RWSB2801 M

RWSS7702

RWDM2305

RWDS2003

RWDB2502SLV

PGBD6020

RLPB2460

RWBR0303

RWDM2303

RWPB0401

RPB2617

RPB0960

ST2460

NB12

N/A

Part Size

60”

24”

60”

36”

N/A

26”

20” x 60”

24” x 60”

N/A

26” x 17”

9” x 60”

24” x 60”

#10-24

N/A

General Instructions

Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used

on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block

of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and

fully engaged.

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel

free to contact our MBI / Edsal Manufacturing facility at, (773) 475-3000 and request customer service.

We can also be reached on the internet at the following email address : [email protected].

To obtain replacement parts, please provide the following information :

- Model # - Part # & Description - Location Purchased - Date Purchased

MBI Consumer Products Division

Edsal Manufacturing Company

4400 South Packers Avenue

Chicago, IL 60609

www.edsal.com

Heavy Duty Work Bench

Take two (2) 24” braces with the shelf ledge facing up,

and one (1) short 36” post and attach rivets from the

brace to the top two (2) holes of the short post. Take

one (1) long 60” post and attach the opposite end of the

brace to the holes of the long post so the brace is

level, tap the brace down to seat. Attach the bottom

brace to the short 36” post using the bottom holes, and

the opposite end to the long 60” post, tap the brace

down to seat. Take one (1) drawer mount and attach

the rivets to the short and long post holes located just

below the 24” braces, and tap down drawer mount to

seat. take one (1) drawer slide and insert it into the

slide of the drawer mount. Repeat this step for the op-

posite end assembly.

Assembly Instructions for MRWB52COS

Add the top wood shelf to the top shelf beam, the drawer

wood shelves to the drawer assemblies, the bottom wood

shelf to the bottom assembly, and the work surface top to

the work surface assembly. Finish the assembly of the

workbench by installing the light fixture to the underside of

the top wood shelf. Install using the hardware and instruc-

tions that are provided with the light fixture.

Step

Post are directional.

The slot must point

down.

Drawer Mount

Drawer Slide

Long Post

Short Post

24” Brace

Shelf Ledge Up

Tap Lightly

26” Drawer Shelf Braces

(Bend facing down & the same

for back of drawer slides also)

Peg Board

Take four (4) 60” beams with the bend facing up, and attach

the rivets even with the braces from the two end assembly's,

and tap down to seat. Install the top shelf beam and one (1)

60” beam with the bend facing down, to the top holes of the

back posts. Next install a peg board bracket to the beam of

the top assembly using the nuts and bolts provided. Assem-

ble the center drawer assembly by taking a peg board bracket,

one (1) shelf support, and one (1) center mounting bracket

and bolt them to the work surface back beam (see figure A).

Next bolt the shelf support bracket, and the last center mount-

ing bracket to the opposite beam. Attach the two (2) center

drawer mounts by placing the rivets into the holes of the cen-

ter mounting brackets. Insert the drawer slides into the center

drawer mount slides. Add the final shelf support to the bot-

tom two (2) beams using the nuts and bolts provided.

Step

Center Drawer Mount

Peg Board Brackets

Figure A

Shelf Support

Top Shelf Beam

60” Beams

Peg Board Bracket

Shelf Support

Center

Mounting

Bracket

Drawer Slides

Place the peg board to the inside of the back post of the work

bench. Using the first hole from the top of the back post,

align the holes of the peg board to the holes on the back

post, and fasten using the nuts and bolts provided. Align the

holes on the peg board brackets to the holes of the peg

board, and fasten the peg board to the peg board brackets

using the nuts and bolts provided. Take the four (4) 26”

drawer shelf braces and with the shelf ledge facing down,

insert the two (2) rivets into the two (2) holes located on the

front of the drawer slides.

60” Beam

(Bend facing down)

Light fixture installs

to the underside of

the top wood shelf.

Top Wood Shelf

Bottom Wood Shelf

Work

Surface

Top

Drawer

Wood

Shelves

Edsal MRWB52COS Assembly Manual

Edsal MRWB52COS Assembly Manual

Edsal MRWB52COS Assembly Manual

Related papers

Other documents