Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety
hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not use this unit for
anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR USE IT AS A LADDER.
Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care when working with metal parts.
Instruction Manual
Heavy Duty 2 Drawer Work Bench
MODEL NUMBER
WB2472 - WB3072
1YCA3 - 1YCA4
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams
and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer
head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal manufacturing facility at,
(773) 475-3000 and request customer service. We can also be reached on the internet at the following email address :
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
WB2472
WB2472
WB2472
-
-
-
1YCA3 2 Drawer
1YCA3 2 Drawer
1YCA3 2 Drawer
-
-
-
60”h x 24”d x 72”w
60”h x 24”d x 72”w
60”h x 24”d x 72”w
Description
Long Post
Brace
Beam
Short Post
Top Shelf Support
Shelf Support
Drawer Mount
Drawer Slide
Drawer Shelf Braces
Center Bracket
Center Drawer Mount
Peg Board
Peg Board Bracket
Bottom Wood Shelf
Top Wood Shelf
Wood Drawer Shelf
Wood Top Shelf
Post Coupler
Hardware
Qty.
4
4
5
2
1
2
2
4
4
2
2
1
4
1
1
2
1
2
24
Part Number
RUPT3602
RWBE2303
RWBE7103
RUPT2402
RWSS8903
RWSB2801
RWDM2305
RWDS2003
RWDB3102
RWBR0303
RWDM2303
PGBD7120
RWPB0401
RLPB2472
MDF2472
RPB23217
RPB2729
RMPC0403
NB24
Part Size
36”
24”
72”
24”
72”
N/A
N/A
N/A
32”
N/A
N/A
20” x 72”
4 3/4” x 1”
24” x 72”
24” x 72”
32” x 17”
9” x 72”
4”
#10-24
WB3072
WB3072
WB3072
-
-
-
1YCA4 2 Drawer
1YCA4 2 Drawer
1YCA4 2 Drawer
-
-
-
60”h x 30”d x 72”w
60”h x 30”d x 72”w
60”h x 30”d x 72”w
Description
Long Post
Brace
Beam
Short Post
Top Shelf Support
Shelf Support
Drawer Mount
Drawer Slide
Drawer Shelf Braces
Center Bracket
Center Drawer Mount
Peg Board
Peg Board Bracket
Bottom Wood Shelf
Top Wood Shelf
Wood Drawer Shelf
Wood Top Shelf
Post Coupler
Hardware
Qty.
4
4
5
2
1
2
2
4
4
2
2
1
4
1
1
2
1
2
24
Part Number
RUPT3602
RWBE2903
RWBE7103
RUPT2402
RWSS8903
RWSB2801
RWDM2905
RWDS2003
RWDB3102
RWBR0303
RWDM2903
PGBD7120
RWPB0401
RLPB3072
MDF3072
RPB23217
RPB2729
RMPC0403
NB24
Part Size
36”
30”
72”
24”
72”
N/A
N/A
N/A
32”
N/A
N/A
20” x 72”
4 3/4” x 1”
30” x 72”
30” x 72”
32” x 17”
9” x 72”
4”
#10-24
Assembly Instructions for Heavy Duty 2 Drawer Work Bench
Assembly Instructions for Heavy Duty 2 Drawer Work Bench
Assembly Instructions for Heavy Duty 2 Drawer Work Bench
Take four (4) beams with the bend facing up, and attach the
rivets even with the braces from the two end assembly's, and
tap down to seat. Install the top shelf beam and one (1) beam
with the bend facing down, to the top holes of the back
posts. Next install the four (4) peg board brackets to the rear
top and center beams, using the nuts and bolts provided.
Assemble the center drawer assembly by taking one (1) shelf
support, and one (1) center mounting bracket and bolt them to
the work surface back beam (see figure A). Next bolt the shelf
support bracket, and the last center mounting bracket to the
opposite beam. Attach the two (2) center drawer mounts by
placing the rivets into the holes of the center mounting brack-
ets. Insert the drawer slides into the center drawer mount
slides. Add the final shelf support to the bottom two (2)
beams using the nuts and bolts provided.
Place the peg board to the inside of the back post of the work
bench. Align the holes of the peg board to the holes on the
back post, and fasten using the nuts and bolts provided.
Align the holes on the peg board brackets to the holes of the
peg board, and fasten the peg board to the peg board brack-
ets using the nuts and bolts provided. Take the four (4)
drawer shelf braces and with the shelf ledge facing down,
insert the two (2) rivets into the two (2) holes located on the
drawer slides.
Add the wood shelves to the top shelf support, the draw-
ers, the bottom shelf, and the work surface to finalize the
assembly of the workbench.
Step
2
Step
3
Step
4
Center Drawer Mount
Peg Board Brackets
Figure A
Shelf Support
Top Shelf Beam
Beams
Peg Board
Bracket
Shelf Support
Center
Mounting
Bracket
Drawer Slides
Drawer Shelf Braces
(Bend facing down)
(Back of drawer slides also)
Peg Board
Beam
(Bend facing down)
Start by taking one (1) 24” short post, one (1) 36” long
post, and one (1) post coupler, and join the two post to-
gether to create the back post. Take one (1) brace with
the shelf ledge facing up, and one (1) long 36” post and
attach the rivets of the brace to the top two (2) holes of
the 36” long post. Take the back post and attach the op-
posite rivets of the brace to the holes of the back post so
the brace is level. Tap brace down to seat. Attach the
bottom brace to the front 36” post skipping one (1) hole
from the bottom and the opposite end to the back post,
tap brace down to seat. Take one (1) drawer mount and
skip one (1) hole from the top brace and attach rivets
to the short and long post, tap down to seat. Take one
(1) drawer slide and insert it into the slide of the drawer
mount. Repeat steps for the opposite end assembly.
Step
1
Drawer Mount
Drawer Slide
Long Post
Front 36” Long Post
Short Post
Back Post Assembly
24” Brace
Post
Coupler
Long Post
(Top 36”)
Short Post
(Bottom 24”)
Shelf Ledge Up
Skip Hole
From Bottom
Tap Lightly
/
