Edsal MRWB-3 Assembly Manual

Edsal
Brand
Edsal
Model
MRWB-3
Type
Assembly Manual
Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
Heavy Duty 3’
1 Drawer Work Bench
MODEL NUMBER
MRWB - 3
MRWB
MRWB
MRWB
-
-
-
3 3 Shelf 1 Drawer
3 3 Shelf 1 Drawer
3 3 Shelf 1 Drawer
-
-
-
72”h x 18”d x 36”w
72”h x 18”d x 36”w
72”h x 18”d x 36”w
Description
Long Post (back)
Brace
Beam
Short Post (front)
Top Shelf Support
Drawer Mount
Drawer Slide
Drawer Shelf Braces
Peg Board
Wood Shelf
Wood Drawer Shelf
Wood Top Shelf
Hardware
Post Coupler
Qty.
4
4
5
2
1
2
2
2
1
2
1
1
2
2
Part Number
RUPT3602
RWBE1703
RWBE3503
RUPT3002
RWSS3503
RWDM1705
RWDS1403
RWDB3102
PGBD3620
RLPB1836
RPB31011
RPB2369
NB2
RMPC0409
Part Size
36”
18”
36”
30”
36”
N/A
N/A
31”
20” x 36”
18” x 36”
11” x 31”
9” x 36”
#10-24
4”
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Edsal manufacturing facility at, (773) 475-3000 and request customer service. We can
also be reached on the internet at the following email address : customerservice@edsal.com.
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
Taking two (2) 36” long post, and one (1) post coupler and
join the two post together to create the back post. Take
one (1) 18” brace with the shelf ledge up, and one (1)
short 30” post and attach the rivets of the brace to the top
two (2) holes of the 30” short post. Take the back post
and attach the opposite rivets of the brace to the holes so
the brace is level. Tap brace down to seat. Attach the
bottom 18” brace to the front 30” post by skipping one (1)
hole from the bottom, and the opposite end to the back
post so that the brace is level, tap brace down to seat.
Take one (1) drawer mount and skip one (1) hole down
from the top brace and attach rivets level, to the short
and long post, tap down to seat. Take one (1) drawer
slide and insert it into the slide of the drawer mount. Re-
peat steps for the opposite end assembly.
Assembly Instructions for MRWB
Assembly Instructions for MRWB
Assembly Instructions for MRWB
-
-
-
3
3
3
Take four (4) 36” beams with the bend facing up, and
attach the rivets even with the braces from the two end
assembly's, and tap down to seat. Install the top shelf
support with the shelf ledge facing down, by installing
the rivets of the top shelf support to the top two (2) holes
of the back post. Install one (1) 36” beam with the shelf
ledge facing down, to the top holes of the back posts,
even with the rivets from the top shelf.
Place the peg board to the inside of the back post of the work
bench. Align the holes of the peg board to the holes on the
back post, and fasten using the nuts and bolts provided.
Take the two (2) 31” drawer shelf braces and with the shelf
ledge facing down, insert the two (2) rivets into the two (2)
holes located on the drawer slides, for the front and back of
the drawer.
Install the handle to the front drawer brace, and add the
wood shelves to the top shelf support, drawers, bottom
shelf, and work surface to finalize the assembly of the
workbench.
Step
1
Step
2
Step
3
Step
4
Post are directional.
The slot must point
down.
Drawer Mount
Drawer Slide
Long Post
Front 30” Short Post
Shelf Ledge Up
Skip Hole From Bottom
Tap Lightly
Peg Board
Post
Coupler
Long Post
Long Post
(Top 36”)
Long Post
(Bottom 36”)
31” Drawer Shelf Braces
(Bend facing down)
(Back side also)
Top Shelf Support
36” Beams
36” Beam
(Bend facing down)
Back Post Assembly
18” Brace
  • Page 1 1
  • Page 2 2

Edsal MRWB-3 Assembly Manual

Edsal
Brand
Edsal
Model
MRWB-3
Type
Assembly Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents