Edsal MRWB-6 Assembly Manual

Brand: Edsal

Model: MRWB-6

Type: Assembly Manual

Safety Instructions

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a

possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not

included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY

PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the

heavier loads on the bottom. Use care when working with metal parts.

Heavy Duty 6’

Work Bench

MODEL NUMBER

MRWB - 6

MRWB

6 3 Shelf 2 Drawer

60”h x 24”d x 72”w

Description

Long Post

Brace

Beam

Short Post

Shelf Support

Top Shelf Beam

Drawer Mount

Drawer Slide

Drawer Shelf Braces

Peg Board

Wood Shelf

Center Bracket

Center Drawer Mount

Peg Board Bracket

Wood Drawer Shelf

Wood Top Shelf

Hardware

Qty.

Part Number

RUPT6002

RWBE2303

RWBE7103

RUPT3602

RWSB2801

RWSS8903

RWDM2305

RWDS2003

RWDB3102

PGBD7120

RLPB2472

RWBR0303

RWDM2303

RWPB0401

RPB23217

RPB2729

NB12

Part Size

60”

24”

72”

36”

N/A

32”

20” x 72”

24” x 72”

N/A

32” x 17”

9” x 72”

#10-24

General Instructions

Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used

on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block

of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and

fully engaged.

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel

free to contact our Edsal manufacturing facility at, (773) 475-3000 and request customer service. We can

also be reached on the internet at the following email address : customerservice@edsal.com.

To obtain replacement parts, please provide the following information :

- Model # - Part # & Description - Location Purchased - Date Purchased

Consumer Products Division

Edsal Manufacturing Company

4400 South Packers Avenue

Chicago, IL 60609 www.edsal.com

Heavy Duty Work Bench

Take two (2) 24” braces with the shelf ledge facing up, and

one (1) short 36” post and attach rivets from the brace to the

top two (2) holes of the short post. Take one (1) long 60”

post and attach the opposite end of the brace to the holes of

the long post so the brace is level, tap down brace to seat.

Attach the bottom brace to the short post skipping one (1)

hole from the bottom and the opposite end to the long post,

tap down brace to seat. Take one (1) drawer mount and skip

one (1) hole from the top brace and attach rivets to the

short and long post, tap down drawer mount to seat. take

one (1) drawer slide and insert it into the slide of the drawer

mount. Repeat this step for the opposite end assembly.

Assembly Instructions for MRWB

Take four (4) 72” beams with the bend facing up, and attach

the rivets even with the braces from the two end assembly's,

and tap down to seat. Install the top shelf beam and one (1)

72” beam with the bend facing down, to the top holes of the

back posts. Next install a peg board bracket to the beam of

the top assembly using the nuts and bolts provided. Assem-

ble the center drawer assembly by taking a peg board bracket,

one (1) shelf support, and one (1) center mounting bracket

and bolt them to the work surface back beam (see figure A).

Next bolt the shelf support bracket, and the last center mount-

ing bracket to the opposite beam. Attach the two (2) center

drawer mounts by placing the rivets into the holes of the cen-

ter mounting brackets. Insert the drawer slides into the center

drawer mount slides. Add the final shelf support to the bot-

tom two (2) beams using the nuts and bolts provided.

Place the peg board to the inside of the back post of the work

bench. Using the fourth hole from the top of the back post,

align the holes of the peg board to the holes on the back

post, and fasten using the nuts and bolts provided. Align the

holes on the peg board brackets to the holes of the peg

board, and fasten the peg board to the peg board brackets

using the nuts and bolts provided. Take the four (4) 32”

drawer shelf braces and with the shelf ledge facing down,

insert the two (2) rivets into the two (2) holes located on the

drawer slides.

Add the wood shelves to the top shelf support, the draw-

ers, the bottom shelf, and the work surface to finalize the

assembly of the workbench.

Step

4th Hole Down

Post are directional.

The slot must point

down.

Drawer Mount

Drawer Slide

Long Post

Short Post

24” Brace

Shelf Ledge Up

Skip Hole From Bottom

Tap Lightly

Center Drawer Mount

Peg Board Brackets

Figure A

Shelf Support

Top Shelf Beam

72” Beams

Peg Board Bracket

Shelf Support

Center

Mounting

Bracket

Drawer Slides

32” Drawer Shelf Braces

(Bend facing down)

(Back of drawer slides also)

Peg Board

72” Beam

(Bend facing down)

Edsal MRWB-6 Assembly Manual

Edsal MRWB-6 Assembly Manual

Edsal MRWB-6 Assembly Manual

Related papers

Other documents