Extron TMK 120 R User manual

Extron
Brand
Extron
Model
TMK 120 R
Category
Mounting kits
Type
User manual
TMK 120 R • Installation Guide
The TMK 120 R Table Mount Kit allows under-table installations for one or two Retractors.
The kit secures the Retractors to the underside of a table.
ATTENTION:
• Do not drill through the table or furniture. If the table is too thin or of a different
material for the supplied screws, use an appropriate type and length.
• Ne perçez pas à travers la table ou le meuble. Si la table est trop ne ou faite dans
un matériau différent de celui pour lequel les vis fournies sont prévues, utilisez un
type de matériau et une longueur appropriés.
Tighten
Install (2) #6 x 1/2 inch wood screws
(provided) into the pilot holes.
Tighten until 1/4 inch protrudes.
Drill 3/32-inch (2.4 mm) diameter,
1/4 inch (6.3 mm) deep pilot
holes.
Place the TMK 120 R under the table
at the desired mounting location.
Mark the two keyhole locations.
Slide the mounting bracket onto the screws.
(2)
Tighten the two screws.
Mount the TMK 120 R bracket as follows:
Tighten
Install (2) #6 x 1/2 inch wood screws
(provided) into the pilot holes.
Tighten until 1/4 inch protrudes.
Drill 3/32-inch (2.4 mm) diameter,
1/4 inch (6.3 mm) deep pilot
holes.
Place the TMK 120 R under the table
at the desired mounting location.
Mark the two keyhole locations.
Slide the mounting bracket onto the screws.
(2)
Tighten the two screws.
NOTE: When selecting a mounting location, consider that cables are connected to the
Retractor from the rear, the retractor button assembly protrudes from the front of
the bracket, and the button assembly must be readily visible to prevent accidental
contact.
Included Parts
1/4-20 x 1 1/2" (4)
Phillips Pan Head Screws
#6-18 x 1/2" (4)
Wood Screws
Included Parts
1/4-20 x 1 1/2" (4)
Phillips Pan Head Screws
#6-18 x 1/2" (4)
Wood Screws
Included Parts
1/4-20 x 1 1/2" (4)
Phillips Pan Head Screws
#6-18 x 1/2" (4)
Wood Screws
Included Parts
1/4-20 x 1 1/2" (4)
Phillips Pan Head Screws
#6-18 x 1/2" (4)
Wood Screws
Included Parts
Bracket (1) Hanger (2) 1/4-20 x 1 1/2"
Phillips pan head
screws (4)
#6 x 1/2"
wood screws (4)
68-2648-50
Rev. A
08 14
Install the Retractor as follows:
1
Remove the top and bottom retractor enclosure screws.
2
Install the retractor with the cable release button against the bracket sidewall.
3
Install and tighten a provided 1/4-20 x 1 1/2" pan head screw.
4
If necessary, rotate the retractor housing for access, then tighten the locking screw.
5
Rotate the rear of the retractor enclosure to the final installation position and install the
hanger to the retractor with a provided 1/4-20 x 1 1/2" pan head screw.
6
Mark the desired mounting position of the hanger under the table and drill a 3/32"
diameter, 1/4" deep pilot hole.
7
6
5
TMK 120 R
7
Fasten the hanger under the table using a provided #6 x 1/2" wood screw.
8
Repeat steps 1-8 to install a second retractor.
NOTE: Do not overtighten. The locking screw
only needs to be snug.
PRESS
2
3
1
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673 (Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron India
1800.3070.3777 (Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
© 2014 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
PRESS
Locking
Screw
4
Rotate
(if necessary)
  • Page 1 1
  • Page 2 2

Extron TMK 120 R User manual

Extron
Brand
Extron
Model
TMK 120 R
Category
Mounting kits
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents