Extron TMK 100 AAP Series User manual

Brand: Extron

Model: TMK 100 AAP Series

Type: User manual

Extron TMK 100 AAP Series allows for under-table installation of up to two or three single-space AAPs, securing them to the underside of a table. It can be mounted side-by-side for additional AAP spaces. The kit includes necessary screws for installation, but users may need to use different screws depending on the table material and thickness.

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

TMK Series • Installation Guide

The TMK series Table Mount Kits allow under-table installation for up to two single-space

AAPs (TMK120AAP) or up to three single-space AAPs (TMK130AAP). Both kits secure

to the underside of a table. The kits can also be mounted side-by-side for applications

requiring additional AAP spaces.

NOTE: The location must consider that cables are connected to the AAPs both from

the front and from the rear, and the bracket and AAPs must be readily visible to

prevent accidental contact.

ATTENTION: Do not drill through the table or furniture. If the table is too thin or of a

different material for the supplied screws, use an appropriate type and length.

USB

CHAR

USB CH

ARGER

Tighten

USB CH

ARGER

USB CH

ARGER

Install #6 x 1/2 inch wood screws

into the pilot holes.

Tighten until 1/4 inch protrudes.

Drill 3/32-inch (2.4 mm) diameter,

1/4 inch (6.3 mm) deep pilot

holes.

Mark the four keyhole locations at

the desired mounting location.

Slide the faceplate onto the screws.

Tighten the front keyhole screws only.

Connect the cables and wiring

to the AAPs.

Install the two sheet metal screws to

secure the faceplate and cover

together.

Tighten the two rear keyhole screws

through the openings in the cover.

Install AAPs in the faceplate.

(4)

Faceplate

Screws (2)

Slide the cover up and into the faceplate.

Make certain the rear slots of the cover

slide into the rear keyhole screws.

#4 x 1/4" (2)

Sheet Metal Screws

#6 x 1/2" (4)

Wood Screws

Cover

aceplate

Included Parts

Mount the TMK bracket as follows:

USB

CHAR

USB CH

ARGER

Tighten

USB CH

ARGER

USB CH

ARGER

Install #6 x 1/2 inch wood screws

into the pilot holes.

Tighten until 1/4 inch protrudes.

Drill 3/32-inch (2.4 mm) diameter,

1/4 inch (6.3 mm) deep pilot

holes.

Mark the four keyhole locations at

the desired mounting location.

Slide the faceplate onto the screws.

Tighten the front keyhole screws only.

Connect the cables and wiring

to the AAPs.

Install the two sheet metal screws to

secure the faceplate and cover

together.

Tighten the two rear keyhole screws

through the openings in the cover.

Install AAPs in the faceplate.

(4)

Faceplate

Screws (2)

Slide the cover up and into the faceplate.

Make certain the rear slots of the cover

slide into the rear keyhole screws.

Extron USA Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673 (Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron India

1800.3070.3777 (Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

68-2456-50

Rev. A

11 13

Extron TMK 100 AAP Series User manual

Extron TMK 100 AAP Series User manual

Extron TMK 100 AAP Series User manual

Related papers

Other documents