Anova AE2680LF Installation guide

Anova
Brand
Anova
Model
AE2680LF
Type
Installation guide

This manual is also suitable for

anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
!
Hammer DrillHammer
Pencil
Wire Brush
Level
Safety Glasses
7)'8-32%%
7'%0)
%
%
% %
& &
THIRD ANGLE PROJECTION
TOLERANCES UNLESS NOTED:
X
1 X.X
.5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX
.015625 ANGULAR ± 1°
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
DRAWN
Airi 6Ft Contour Benches
SIZE
BAE2680_SPEC-REV-002
DATE
7/31/2015
SCALE
.09375:1 SHEET
DWG NO
TITLE
B. MENDEZ
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
REV
1 OF
002
1
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 ORIGINAL PRINT NONE 7/31/15
002
MOVED OVER THE ENTIRE FOOT
MOUNT INSTEAD OF JUST ONE
SIDE AND ADDED THE 73.75" DIM
NONE 8/22/18
*33813928
8,69
<
Airi Benches
.75"
14.73"
Ø.33"
(4 PLCS)
73.75"
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
FOOT MOUNT
(4) 1/4"-20 x 1 3/8"
SS Hex Flat Head Screw
92210A545
(4) 1/4"-20 x 1"
Drop-In Anchor
97083A290
Masonry Drill Bit Set
3/16" and 3/8"
1/4" Drop-in Anchor
Setting Tool
Allen Wrench Set
5/32"
Copyright 2018 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3. Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
8/24/2018
Airi Benches
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 3/16" diameter drill bit followed by the 3/8" diameter bit.
Place the bench in the desired location. Mark the location of the holes with
a pencil. To verify the alignment of the anchor markings you may reference
page 1.
4. Insert one 1/4"-20 x 1" drop-in anchor into the hole and use a hammer to tap
the anchor ush with the concrete.
5.
6.
7.
8.
Use a 1/4" drop-in anchor setting tool and hammer to x the anchor into the
drilled hole by inserting the narrow end of the tool into the anchor and giving
it several hammer blows.
Repeat steps 3 - 6 until all anchors are installed.
Align the mounting holes of the bench over top of the anchors.
Care should be given to avoid rubbing the powder coating o the foot.
Mount the bench to the anchors by fastening a hex head screw into each
anchor. Leave the hardware nger tight until all of them have been installed.
Verify that the bench is level before tightening the anchors. Tighten the
screws with a 5/32" Allen wrench.
!
5
2
5
8.1 8.2
4
7
  • Page 1 1
  • Page 2 2

Anova AE2680LF Installation guide

Anova
Brand
Anova
Model
AE2680LF
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents