Ogden OGM1900 Installation guide

BOTTOM VIEW

TOP VIEW

DETAIL B

4 X 3/8" HARDWARE

(PER EACH STUD)

NOTE LOCATION

OF HARDWARE

DETAIL A

4 X 3/8" HARDWARE

(PER 2 STUDS EACH SEAT SECTION)

NOTE ONLY TWO STUDS PER SIDE

ARE USED

BETWEEN TWO SEAT SECTIONS

MOUNTS - QUICK REFERENCE

END OF ONE SEAT SECTION

NOTE THAT PRINCIPLES SHOWN IN THIS QUICK REFERENCE CAN BE APPLIED TO ALL MOUNT STYLES

OGDEN, BENCH SYSTEM

DWG:

INSTALL_OGDEN

REV:

M01

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

INSTALLATION INSTRUCTIONS: OGDEN - OGM1900

DESCRIPTION:

NOTE THE PRINCIPLES FOR ARCS OR WAVES

APPLY TO ALL MOUNT STYLES.

SEE WALL MOUNT AND CANTILEVER INSTALLATION PAGES

FOR SPECIFIC DETAIL REGARDING THEIR INSTALLATION.

OPEN LAYOUTS REFER TO ANY LAYOUT WITH

A BEGINNING AND AN END (IE. NOT A CIRCLE).

ARC OR WAVE (OPEN LAYOUTS)

NOTE THE PRINCIPLES FOR THE CIRCLE LAYOUTS

APPLY TO ALL MOUNT STYLES.

SEE WALL MOUNT AND CANTILEVER INSTALLATION PAGES

FOR SPECIFIC DETAIL REGARDING THEIR INSTALLATION.

CLOSED LAYOUTS REFER TO ANY LAYOUT WITHOUT A

BEGINNING OR END (IE. CIRCLE).

CIRCLE (CLOSED LAYOUTS)

OGDEN, BENCH SYSTEM

DWG:

INSTALL_OGDEN

REV:

M01

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

INSTALLATION INSTRUCTIONS: OGDEN - OGM1900

DESCRIPTION:

CENTER ARM OR SKATE DETERRENT

CANTILEVER MOUNT

FOR WALL MOUNTS BENCHES PRINCIPLES APPLY TO BOTH

OPEN OR CLOSED LAYOUTS (REFER TO PAGE 1)

WALL MOUNT

NOTE PRINCIPLES FOR ASSEMBLY ARE THE SIMILAR FOR

BOTH THE CENTER ARM AND THE SKATE DETERRENT.

FOR CANTILEVERED SECTIONS PRINCIPLES APPLY TO BOTH

OPEN OR CLOSED LAYOUTS (REFER TO PAGE 1)

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

WRENCH

9/16"

RATCHET WRENCH

9/16"

HEX SOCKET OR ALLEN KEY

7/32"

HAMMER DRILL

(MASON BIT SIZE THAT

MATCHES CHOSEN ANCHOR)

PENCIL

LOCK WASHER

3/8"

FLAT WASHER

3/8"

HEX NUT

3/8"

HEX BOLT

3/8"

LOCTITE

(OPTIONAL)

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

!CAUTION!

FAILURE TO FOLLOW INSTRUCTIONS COULD LEAD TO INJURY, ENSURE ALL STEPS ARE FOLLOWED AND FASTENERS ARE USED, TWO OR MORE PEOPLE ARE REQUIRED FOR INSTALLATION

!CAUTION!

NOTE THAT THE ASSEMBLY THREADED STUDS ONLY AID IN THE ASSEMBLY PROCESS. PARTS SHOULD NOT BE LEFT UNATTENDED AND SHOULD BE BOLTED TOGETHER IMMEDIATELY AFTER

PARTS ARE PLACED IN DESIRED LOCATION AS SEATING IN NOT SAFE FOR USE UNTIL FULLY FASTENED TOGETHER AND ANCHORED DOWN.

!CAUTION!

ALL ASSEMBLIES REQUIRE ADEQUATE ANCHORING TO AN APPROPRIATE SUBSTRATE. DO NOT LEAVE BEANCE FREE STANDING. IT IS THE INSTALLERS RESPONSIBILITY TO USE APPROPRIATE

ANCHORS AND IDENTIFY AN APPROPRIATE SUBSTRATE.

TOOLS (NOT SUPPLIED):

FASTENERS (SUPPLIED):

NOTES:

NOTE THAT QUANTITIES VARY DEPENDING ON THE CHOSEN LAYOUT

15 3/8"

17 1/4"

9/16"

HOLE FOR CONCRETE ANCHOR

17 1/4"

11 1/2"

2"

!CAUTION! -

FOR REFERENCE ONLY. DIMENSIONS ARE SUBJECT TO CHANGE AND MAY VARY. USE ACTUAL PRODUCT TO MARK HOLE LOCATIONS.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

PARTS: LEG SQUARE

14"

15 3/8"

3X

9/16" THRU

HOLES FOR CONCRETE ANCHORS

7"

!CAUTION! -

FOR REFERENCE ONLY. DIMENSIONS ARE SUBJECT TO CHANGE AND MAY VARY. USE ACTUAL PRODUCT TO MARK HOLE LOCATIONS.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

PARTS: LEG PEDESTAL

1 31/32"

5/8"

29/32"

1"

HOLE FOR BENCH ASSEMBLY

2 3/4"

8" - PAIR A

USE ON WALLS

12" OR WIDER

13 1/2"

1"

4" - PAIR B

USE ON WALLS

BETWEEN 8" - 12" WIDE

4X

7/16" THRU

HOLE FOR 3/8" CONCRETE ANCHOR

! USE ONLY ONE PAIR OF HOLES (A OR B) !

4 3/4"

!CAUTION! -

FOR REFERENCE ONLY. DIMENSIONS ARE SUBJECT TO CHANGE AND MAY VARY. USE ACTUAL PRODUCT TO MARK HOLE LOCATIONS.

USE ONLY ONE PAIR OF HOLES TO MOUNT BRACKET (A OR B SEE DRAWING ABOVE).

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

PARTS: WALL MOUNT BRACKET

9/16" THRU

HOLE FOR 1/2" CONCRETE ANCHOR

1 1/2"

7/8"

4 1/2"

16"

3"

7 1/4"

6 1/4"

4 3/16"

2 1/2"

HOLE FOR BENCH ASSEMBLY

HOLES FOR CENTER ARM

LEFT BRACKET

RIGHT BRACKET

!CAUTION! -

FOR REFERENCE ONLY. DIMENSIONS ARE SUBJECT TO CHANGE AND MAY VARY. USE ACTUAL PRODUCT TO MARK HOLE LOCATIONS.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

PARTS: CANTILEVER BRACKET

DETAIL A

HEX NUT

LOCK WASHER

WASHER

TURN BENCH ONTO SEAT SURFACE, ENSURE TO PLACE ON A CLEAN SCRATCH RESISTANT SURFACE.

ATTACH BOTH LEGS TO ONLY 2 THREADED STUDS AND OVERHANG LEG FROM

SEAT SECTION EDGE (DETAIL A). ATTACH WITH 3/8" FASTENERS.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

CIRCLE W/LEGS

1

DETAIL B

HEX NUT

LOCK WASHER

FLAT WASHER

DETAIL C

HEX NUT

LOCK WASHER

FLAT WASHER

FLIP OVER BENCH SECTION. NEXT PLACE NEXT SEAT SECTION ONTO SEAT SURFACE.

AGAIN ENSURE IT IS PLACED ON A CLEAN SCRATCH RESISTANT SURFACE.

ATTACH NEXT LEG BY ALIGNING LEG TO 2 THREADED STUDS ON SEAT TO

2 HOLES ON LEG, ENSURE TO OVERHANG 2 HOLES AND FASTEN USING 3/8" FASTENERS.(DETAIL B)

FLIP OVER SECTION WITH ONE LEG AND ALIGN THE 2 STUDS ON SIDE WITH NO LEG

TO THE 2 OPEN HOLES ON THE PREVIOUSLY ASSEMBLED SECTION (DETAIL C)

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

2

3

DETAIL E

DETAIL F

INSTALLATION NOW COMPLETE.

CONTINUE SAME ASSEMBLY METHODS TO COMPLETE CIRCLE (DETAIL E).

THE LAST SECTION WILL NOT REQUIRE A LEG TO BE ATTACHED AS IT WILL SHARE ONE ON EITHER SIDE.

SHIM BENCH IF NOT LEVEL AND LAG DOWN ALL LEGS INTO APPROPRIATE SUBSTRATE USING APPROPRIATE ANCHORS.

UTILIZE ALL HOLES ON LEGS, 2 PER SQUARE LEG, 3 PER PEDESTAL LEG (DETAIL F).

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

4

5

DETAIL B

FLAT WASHER

LOCK WASHER

HEX NUT

STUDS

DETAIL C

TURN SEAT SECTION ON BACK, ENSURE TO PLACE ON A CLEAN SCRATCH RESISTANT SURFACE.

FIRST IDENTIFY THE BEGINNING OF CHOSEN LAYOUT AND ALIGN LEG TO ALL 4 STUDS (DETAIL B).

IF CONTINUING LAYOUT ALIGN SECOND LEG WITH 2 STUDS AND OVERHANG OTHER 2.

FASTEN LEGS WITH 3/8" FASTENERS. (DETAIL C)

IF LAYOUT IS HAS ONLY ONE BENCH SECTION ATTACH LEG TO ALL 4 STUDS AND ASSEMBLY IS COMPLETE, GO TO STEP 5

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

ARC OR WAVE

1

DETAIL D

HEX NUT

LOCK WASHER

FLAT WASHER

FLIP OVER BENCH SECTION. NEXT PLACE NEXT SEAT SECTION ONTO SEAT SURFACE.

AGAIN ENSURE IT IS PLACED ON A CLEAN SCRATCH RESISTANT SURFACE.

IF LAYOUT IS GOING TO CONTINUE ATTACH NEXT LEG BY ALIGNING LEG TO 2 THREADED STUDS ON SEAT TO

2 HOLES ON LEG, ENSURE TO OVERHANG 2 HOLES AND FASTEN USING 3/8" FASTENERS.(DETAIL D)

IF THIS IS THE LAST SECTION IN THE LAYOUT ATTACH TO ALL 4 STUDS.

FLIP OVER SECTION WITH ONE LEG AND ALIGN THE 2 STUDS ON SIDE WITH NO LEG

TO THE 2 OPEN HOLES ON THE PREVIOUSLY ASSEMBLED SECTION (DETAIL E)

DETAIL E

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

2

3

DETAIL F

POINT G

DETAIL H

CONTINUE SAME ASSEMBLY METHOD TO COMPLETE DESIRED SHAPE.

ENSURE 4 THREADED STUDS OF THE LAST BENCH SECTION ALIGN WITH

4 HOLES ON THE OUTSIDE LEG (POINT G).

SHIM BENCH TO LEVEL IF NECESSARY.

LAG DOWN ALL LEGS INTO APPROPRIATE SUBSTRATE USING APPROPRIATE ANCHORS.

UTILIZE ALL HOLES ON LEGS, 2 PER SQUARE LEG, 3 PER PEDESTAL LEG (DETAIL H).

INSTALLATION NOW COMPLETE.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

4

5

DETAIL B

POINT A

POINT B

FIRST IDENTIFY WHETHER LAYOUT IS AN OPEN OR CLOSED LAYOUT (REFER TO PAGE 1).

PLACE ALL SECTIONS ON WALL AND MARK BRACKETS WHERE FINAL INSTALL IS DESIRED. THEN REMOVE ALL PIECES

NEXT ATTACH FIRST 2 BRACKETS IN APPROPRIATE LOCATION FOR CHOSEN LAYOUT STYLE (OPEN OR CLOSED).

PLACE BENCH SECTION INCLUDING BRACKETS ON WALL. (SEE - MOUNTS - QUICK REFERENCE, PAGE 1)

NEXT DETERMINE THE WIDTH OF THE CONCRETE WALL. USE

ONLY

TWO HOLES, EITHER PAIR A FOR WALLS 12" AND WIDER

OR PAIR B FOR WALLS BETWEEN 8"-12". MARK HOLE LOCATIONS (POINT A OR B) WITH PENCIL OR MARKER.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

WALL MOUNT

1

DETAIL C

DETAIL D

SCALE 1 : 6

DRILL HOLES AT MARKED LOCATION TO CORRECT SIZE AND

DEPTH FOR CONCRETE ANCHORS. ENSURE TO FOLLOW

ANCHOR AND CONCRETE SPECS WHEN DRILLING CLOSE

TO CONCRETE EDGE.

REMOVE BOTTOM HALF OF WALL MOUNT BRACKETS FROM BENCH

ASSEMBLY USING 7/32" HEX KEY. (DETAIL D)

KEEP FASTENERS FOR RE-ASSEMBLY IN A LATER STEP.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

2

3

DETAIL E

DETAIL F

ALIGN BOTTOM HALF OF BRACKET WITH HOLES THAT HAVE BEEN DRILLED

AND FASTEN DOWN WITH CHOSEN CONCRETE ANCHORS (DETAIL D).

ALIGN BENCH WITH BRACKETS.

USING 7/32" ALLEN KEY FASTEN BENCH SECTION TO BRACKETS (DETAIL F)

USING FASTENERS PREVIOUSLY REMOVED.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

4

5

G

DETAIL G

SCALE 1 : 10

DETAIL H

3/8" HARDWARE

NEXT DETERMINE IF YOUR LAYOUT CONTINUES OR ENDS AFTER ADDING THIS NEXT SECTION. ATTACH

BRACKET TO THE CORRECT LOCATION AND NUMBER OF STUDS (DETAIL G)(SEE - MOUNTS - QUICK REFERENCE, PAGE 1)

MARK BRACKET HOLE LOCATIONS AS COMPLETED IN STEP 1.

NEXT FOLLOW STEPS 2-5 FOR THIS BENCH SECTION FOR ALL OTHERS SECTIONS IN LAYOUT.

LASTLY FASTEN ALL BENCH SECTIONS TO THE WALL BRACKETS USING

3/8" HARDWARE USING WASHER, LOCK WASHER, AND HEX NUT (DETAIL H).

ENSURE ALL FOR STUDS ARE FASTENED TO EACH BRACKET

INSTALLATION IS NOW COMPLETE.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

6

7

DETAIL B

POINT A

FIRST IDENTIFY WHETHER LAYOUT IS AN OPEN OR CLOSED LAYOUT (REFER TO PAGE 1)

***IMPORTANT THERE ARE LEFT AND RIGHT BRACKETS. ENSURE CORRECT BRACKET IS PLACED AT THE END OF OPEN LAYOUTS. ONE LEFT AND ONE RIGHT ON EITHER SIDE***

NEXT TEMPORARILY ATTACH 2 BRACKETS USING 3/8" HARDWARE TO FIRST BENCH SECTION

IN APPROPRIATE LOCATION FOR CHOSEN LAYOUT STYLE (OPEN OR CLOSED).

NEXT PLACE BENCH ASSEMBLY INCLUDING BRACKETS AGAINST WALL.

(AT LEAST TWO PEOPLE REQUIRED. PROP UP BENCH TEMPORARILY IF NECESSARY)

AT DESIRED LOCATION AND LEVEL IF NECESSARY . MARK ALL BRACKETS HOLE LOCATIONS (POINT A) WITH PENCIL OR MARKER.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

CANTILEVER

1

DETAIL C

DETAIL D

DRILL HOLES AT MARKED LOCATION TO CORRECT SIZE AND

DEPTH FOR CONCRETE ANCHORS. ENSURE TO FOLLOW

ANCHOR AND CONCRETE SPECS WHEN DRILLING CLOSE

TO CONCRETE EDGE.

REMOVE BRACKETS FROM BENCH ASSEMBLY THAT HAS BEEN SET ASIDE.

HOLD ONTO FASTENERS.

WWW.MAGLIN.COM

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MAGLIN SITE FURNITURE INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MAGLIN SITE FURNITURE INC. IS PROHIBITED.

2

3

Page is loading ...

Ogden OGM1900 Installation guide

Ogden OGM1900 Installation guide

Other documents