Anova TRI84HIM Installation guide

Brand: Anova

Model: TRI84HIM

Type: Installation guide

anovafurnishings.com

888.535.5005 tel

Installation Instructions

Screens and Panels - Embedded Mount Privacy Screens

TOOLS AND SUPPLIES NEEDED: HARDWARE NEEDED:

Step-by-Step Installation Sequence

The posts need to be installed before assembling the privacy screen or panel system.

Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at

a 3,000 psi minimum and be cured for at least 28 days prior to the installation of the privacy screen or panel

system.

CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.

Post Hole Digger Optional: Digging Iron Sledge Hammer Shovel 2" x 4"

Board

Stakes String or Rope

Wood Screws

(2 or more) Clamps:

With rubber pads

Level

Drill and a

Drill Bit Set

Installation Instructions

Step-by-Step Installation Sequence

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

7. Check the concrete manufacturer's specications to see how long the

concrete needs to dry before proceeding to attach the remaining parts. Once

the concrete has properly set you may proceed with the assembly.

Using a shovel place approximately six inches of gravel into the hole then

tamp it down with a 2" x 4". Repeat this step one more time so there is a total

of 6" of gravel.

Place the post in the center of the hole. It should go down 24" for a 4' post or

36" for an 8' post. It is necessary to set up a couple of braces to ensure the

proper height and that the post is level.

To do so hammer a couple of wood posts into the ground using a sledge

hammer and screw another post to each post using a drill. Then use clamps to

brace the posts together.

NOTE: When bracing the post in place you should constantly be checking it

with a level to ensure that it set properly.

NOTE: When digging the hole it is recommended that it has a slight angle and

increases in size the farther down it goes. This helps prevent frost upheaval.

Mix the concrete in a wheel barrel to the manufacturer's specications.

NOTE: Check with a local contractor for the best option on how to pour

the concrete. Images 6.1 and 6.2 show two standard practices, but we still

recommend seeking out a local contractor.

Pour the concrete based on your local recommendation.

Dig out the holes for the posts using a post hole digger and a digging iron. The

distance between holes should be determined by the size of panel being used

and should be a minimum of 6" diameter hole. The depth of the hole should

be below the frost line to prevent shiing.

Stake out the outline of the area of where the fencing is going to be installed

and attach string to the outer stakes to ensure the holes are dug along the

correct path.

2 3

CAUTION: Call your local utility companies to mark where there are any

cables or pipelines before digging any holes.

Frost Line

6.1 6.2

Screens and Panels - Embedded Mount Privacy Screens

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

Manufactured in the U.S.

Installation Instructions

Screens and Panels - Embedded Mount Privacy Screens

10/18/2021

FOOT MOUNTS:

4FT FOOTPRINT:

6FT FOOTPRINT:

8FT FOOTPRINT:

54.00

6.00

.64

(8 PLCS)

SECTION A-A

78.00

6.00

.64

(8 PLCS)

SECTION A-A

SCALE 1 : 5

102.00

6.00

.64

(8 PLCS)

SECTION A-A

SCALE 1 : 6.5

48" Distance from Center to Center

72" Distance from Center to Center

96" Distance from Center to Center

Installation Instructions

Screens and Panels - Embedded Mount Privacy Screens

Inspect the shipping container contents for damage and to

determine that all components and hardware are present.

2. Lay all parts on a so work surface or on the shipping

packaging to prevent damage to nish.

NOTE: Before assembling the nuts to the bolts, it is

recommended that a light oil or petroleum jelly be applied

to the screw threads.

COMPONENT PARTS:

ASSEMBLY HARDWARE: All hardware is stainless steel.

ASSEMBLY:

anovafurnishings.com

888.535.5005 tel

Embedded Mount Post(s) Panel(s)

TOOLS NEEDED:

• 9/16" Wrench or Socket

• 7/16" Wrench or Socket

1/4"-20 Stainless Steel

Cap Nut(s)

5/16" Stainless Steel

Flat Washer

1/4"-20 Stainless Steel

Carriage Bolt(s)

72.2500

23.8750

2.5000

REVISIONS

REV.

DESCRIPTION

ECN TR #

DESIGNER DATE

A00 ORIGINAL PRINT

NONE

End Junction 4 Foot Inground Mount Post

A00

4FT000POSTIM

SHEET 1 OF 1

1:10

11/3/2021

REV

DWG. NO.

SIZE

TITLE:

PRINT IS FOR FABRICATION ONLY. ALL SURFACES

MAY EXPAND BY .125± .0625 DURING COATING.

ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES

OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED

DO NOT SCALE DRAWING

211 North Lindbergh Blvd.

St. Louis, MO 63141

888.535.5005 tel

314.754.0835 fax

[email protected]

anovafurnishings.com

THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF

ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.

THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.

THIRD ANGLE PROJECTION

DRAWN

DATE

S. Rocca

TOLERANCES UNLESS NOTED:

X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125

X.XXXX ± .0625 X.XXXXX ± .03125

X.XXXXXX ± .015625 ANGULAR ± 1°

A A

B B

SCALE

11/3/2021

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

Manufactured in the U.S.

Carriage Bolt

Replacement Parts

Flat Washer

Cap nut

3. Once the posts are secured in the ground, locate two

carriage bolts, two washers, and two cap nuts. Attach the

panel to one post by inserting a carriage bolt rst through

the top square hole on either end of the panel, then

through the post's bracket.

Secure the carriage bolt on the back side of the bracket by

inserting on a washer followed by a cap nut.

Repeat this process on the top square hole on the opposite

end of the panel.

Repeat for all remaining mounting holes on the panel.

Posts

Panel

Anova TRI84HIM Installation guide

Anova TRI84HIM Installation guide

Anova TRI84HIM Installation guide

Related papers

Other documents