Whirlpool AKR 958 IX WP Program Chart

Whirlpool
Brand
Whirlpool
Model
AKR 958 IX WP
Category
Cooker hoods
Type
Program Chart

Whirlpool AKR 958 IX WP is a cooker hood designed for efficient extraction and purification of cooking fumes and odors. Here are some of its key features and possible use cases:

  • Extraction and Purification: The hood is equipped with a powerful motor that effectively extracts cooking fumes, grease, and odors from the air, providing a cleaner and fresher kitchen environment.

  • Multiple Speed Settings: It offers three speed settings - minimum, medium, and maximum - allowing you to adjust the extraction power based on your cooking needs.

  • Halogen Lighting: The hood features halogen bulbs that provide bright illumination of the cooking area, enhancing visibility while cooking.

Whirlpool AKR 958 IX WP is a cooker hood designed for efficient extraction and purification of cooking fumes and odors. Here are some of its key features and possible use cases:

  • Extraction and Purification: The hood is equipped with a powerful motor that effectively extracts cooking fumes, grease, and odors from the air, providing a cleaner and fresher kitchen environment.

  • Multiple Speed Settings: It offers three speed settings - minimum, medium, and maximum - allowing you to adjust the extraction power based on your cooking needs.

  • Halogen Lighting: The hood features halogen bulbs that provide bright illumination of the cooking area, enhancing visibility while cooking.

5019 318 33192
INSTALLATION SHEET
Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or coal cookers). To
install, follow points (1
Ö
2
Ö
3
Ö
.....). Do not connect the appliance to the electrical power supply
until installation is completed.
If the installation instructions for the gas cooker specify a greater distance, this must be taken into
account. Warning! The exhaust pipe and clamps (15) are not supplied and must be bought
separately.
Contact a qualified technician for installation.
GB
31833192GB.fm Page 1 Wednesday, December 21, 2005 3:55 PM
5019 318 33192
31833192GB.fm Page 2 Wednesday, December 21, 2005 3:55 PM
5019 318 33192
31833192GB.fm Page 3 Wednesday, December 21, 2005 3:55 PM
5019 318 33192
Preliminary information for installing the hood
Before starting installation, disconnect the power supply at the home main switch.
Remove the grease filter/s and the carbon filter holder.
1.
Pre-assemble the three parts of the flue support bracket with 4 screws; the width
X
of the bracket
G
must be identical to
the internal width of the telescopic flue.
For filter version only
Pre-assemble the three parts of the deflector with 2 screws; the width
X
of the deflector
F
must be identical to the internal
width of the telescopic flue.
2.
Place the extraction unit on a flat surface and fit the bottom part of the hood on it.
Secure it with 4 screws.
Model AKR 958 only
Carry out the electrical connections between the two parts.
3.
Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.
4.
Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the centre line drawn
on the wall, and the lower edge of the hole diagram must match the lower edge of the hood.
Remember that with installation completed the bottom of the hood must be at least 50 cm above the hob in case of electric
cookers and 75 cm in case of gas or mixed cookers.
5.
Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two external holes and
drill, remove the hole diagram.
6.
Insert 2 wall plugs and fix the hood support bracket with two 5x45 mm screws.
7.
Hook the hood to the bracket.
8.
Adjust the distance between the hood and the wall.
9.
Adjust the hood horizontally.
10.
From the inside of the extraction unit, mark the holes for fixing the hood (to do so, remove the filter holder; refit it after
fixing the hood).
11.
Remove the hood from the bracket and drill on the mark (Ø 8 mm - see step 10). Insert 1 wall plug.
12.
Fit the flue support bracket
G
to the wall and against the ceiling, use the support bracket as hole diagram (the small slot on
the support must match the line drawn on the wall - step 3) and mark 2 holes with the pencil, drill the holes (Ø 8 mm),
and finally insert 2 plugs.
13.
Fix the flue support bracket to the wall with two 5x45 mm screws.
14.
Hook the hood to the bottom bracket. Fix the hood to the wall with a 5x45mm screw (ABSOLUTELY NECESSARY).
15.
Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar
B
located above
the extraction motor unit.
For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter operation, fix
the deflector
F
to the flue support bracket
G
with 4 screws and connect the other end of the exhaust pipe to the deflector
collar
F
(if the collar is not already fitted it should be inserted on the deflector and secured with 1 screw). Once the steam
and fumes have been filtered by the carbon filter (not provided, to be ordered separately) they are conveyed back to the
kitchen through grid
H
.
16.
Carry out the electrical connection.
17.
Fit the casing on the runners.
18.
Fix the casing to the hood with 4 screws.
19.
Apply the flues and fix them with 2 screws (
19a
) to the flue support
G
(
19b
).
20. Model AKR 928 only
: Carry out the electrical connections between the two parts.
21.
Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction unit and fix it to
the hood (
21a
) with 2 screws (
22b
).
Refit the grease filter/s and the carbon filter holder, and check for correct hood operation.
INSTALLATION - ASSEMBLY INSTRUCTIONS
TR GB
31833192GB.fm Page 4 Wednesday, December 21, 2005 3:55 PM
5019 318 33192
1.
Control panel.
a.
Light ON/OFF switch.
b.
Extraction and minimum extraction speed
ON/OFF switch.
c.
Medium extraction speed switch.
d.
Maximum extraction speed switch.
2.
Grease filter.
3.
Halogen bulbs.
4.
Steam deflector.
5.
Telescopic flue.
To clean the grease filter
Wash the grease filter at least once a month.
1.
Disconnect the electrical power supply.
2.
Remove the grease filters -
Fig. 1
:
AKR 928
... pull the spring release handle (
f
) downwards, then
remove the filter.
AKR 958
... push the spring release handle backwards (
f1
), then
remove the filter downwards (
f2
).
3.
After cleaning the grease filter refit in reverse order,
making sure the entire extraction surface is covered.
Replacing bulbs
1.
Disconnect the electrical power supply.
2.
Use a small screwdriver or any other suitable tool to prise
off (
m-Fig. 2
) the lamp cover (
p-Fig. 2
).
3.
Remove the burnt-out bulb.
Use 20W max halogen bulbs only, taking care not to touch
them with your hands.
4.
Close the lighting unit (snap-close).
Carbon filter Fitting and Maintenance
Fitting the carbon filter:
1.
Disconnect the electrical power supply.
2.
Remove the grease filter (
Fig. 1
).
3.
Turn the side knobs 90° and then remove the filter holder
(
g - Fig. 3
).
4.
Fit the carbon filter (
h - Fig. 3
) in the filter holder
(
i - Fig.
3
).
5.
Refit the filter holder and secure it to the hood with the
screw (
g - Fig. 3
).
6.
Refit the grease filter.
Fitting the carbon filter:
Unlike traditional carbon filters, this carbon filter can be
washed and reactivated.
With normal hood use, the filter should be cleaned once a
month. The best way to clean the filter is in a dishwasher at
the highest temperature possible, using a normal dishwasher
detergent. To avoid particles of food or dirt settling on the
filter during washing and giving rise to unpleasant smells, it is
advisable to wash the filter on its own. After washing, dry the
filter in the oven at 100°C for 10 minutes to reactivate it.
The filter will retain its odour-absorbing capacity for three
years, after which it must be replaced.
Fig. 1
Fig. 2
Fig. 3
AKR 928
AKR 958
AKR 958
AKR 928
PRODUCT SHEET
TR GB
31833192GB.fm Page 5 Wednesday, December 21, 2005 3:55 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Whirlpool AKR 958 IX WP Program Chart

Whirlpool
Brand
Whirlpool
Model
AKR 958 IX WP
Category
Cooker hoods
Type
Program Chart

Whirlpool AKR 958 IX WP is a cooker hood designed for efficient extraction and purification of cooking fumes and odors. Here are some of its key features and possible use cases:

  • Extraction and Purification: The hood is equipped with a powerful motor that effectively extracts cooking fumes, grease, and odors from the air, providing a cleaner and fresher kitchen environment.

  • Multiple Speed Settings: It offers three speed settings - minimum, medium, and maximum - allowing you to adjust the extraction power based on your cooking needs.

  • Halogen Lighting: The hood features halogen bulbs that provide bright illumination of the cooking area, enhancing visibility while cooking.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents