Bauknecht DDT 7790 IN Program Chart

Brand: Bauknecht

Model: DDT 7790 IN

Category: Cooker hoods

Type: Program Chart



5019 418 33034

DDT 7790

INSTALLATIONSANGABEN

Mindestabstand zur Kochfläche: 50 cm (Elektrokochplatten), 75 cm (Gas-, Öl- oder

Kohlekochplatten). Folgen Sie bei der Installation der Nummerierung (1Ö2Ö3Ö....).

Schließen Sie das Gerät erst nach erfolgter Installation an die Stromversorgung an.

Achtung! Das Auslassrohr und die Befestigungsmanschetten (15) sind nicht im

Lieferumfang inbegriffen und müssen gesondert erworben werden.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or coal

cookers). To install, follow points (1Ö2Ö3Ö.....). Do not connect the appliance to the

electrical power supply until installation is completed. Warning! The exhaust pipe

and clamps (15) are not supplied and must be bought separately.

FICHE D’INSTALLATION

Distance minimale par rapport à la cuisinière : 50 cm (cuisinière électrique), 75 cm

(cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la numérotation

(1Ö2Ö3Ö.....). Ne branchez pas l’appareil tant que l'installation n’est pas terminée.

Attention ! Le conduit d'évacuation et les colliers de fixation (15) ne sont pas

fournis et doivent être achetés à part.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 50 cm (elektrische kooktoestellen), 75 cm

(kooktoestellen op gas, olie of kolen). Volg voor de montage de nummering

(1Ö2Ö3Ö.....). Geef het apparaat geen stroom totdat de installatie geheel voltooid

is. Let op de afvoerbuis en de klembanden (15) worden niet bijgeleverd en moeten

apart worden aangeschaft.

FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 50 cm (quemadores eléctricos), 75 cm

(quemadores de gas, gasóleo o carbón). Para el montaje, siga la numeración

(1Ö2Ö3Ö...). No conecte el aparato a la corriente eléctrica hasta que la instalación

esté completamente finalizada. ¡Atención! El tubo de descarga y las abrazaderas

(15) no están incluidas y se compran aparte.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 50 cm (fogões eléctricos), 75 cm (fogões a gás,

gasóleo ou carbono). Para a montagem siga a numeração (1Ö2Ö3Ö.....). Não ligue o

aparelho à corrente eléctrica até a instalação estar concluída. Atenção! O tubo de

descarga e as tiras de fixação (15) não são fornecidas e devem ser compradas à parte.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 50 cm (fuochi elettrici), 75 cm (fuochi a gas, gasolio o

carbone). Per il montaggio seguire la numerazione (1Ö2Ö3Ö.....). Non dare corrente

all’apparecchio finché l’installazione non è totalmente completata. Attenzione! Il

tubo di scarico e le fascette di fissaggio (15) non sono fornite e vanno acquistate a

parte.

ȀǹȇȉǼȁǹ ǼīȀǹȉǹȈȉǹȈǾȈ

ǼȜȐȤȚıĲȘ ĮʌȩıĲĮıȘ Įʌȩ ĲȚȢ İıĲȓİȢ: 50 cm (ȘȜİțĲȡȚțȑȢ İıĲȓİȢ), 70 cm (İıĲȓİȢ ĮİȡȓȠȣ,

ʌİĲȡİȜĮȓȠȣȒ µİ țȐȡȕȠȣȞȠ). īȚĮ ĲȘȞ ĲȠʌȠșȑĲȘıȘ ĮțȠȜȠȣșȒıĲİ ĲȘȞ ĮȡȓșµȘıȘ (1Ö2Ö3Ö.....).

ȂȘȞ ĲȡȠĳȠįȠĲİȓĲİ µİ ȘȜİțĲȡȚțȩ ȡİȪµĮ ĲȘ ıȣıțİȣȒ ʌȡȚȞ ĲȘȞ ȠȜȠțȜȒȡȦıȘ ĲȘȢ

İȖțĮĲȐıĲĮıȘȢ. ȆȡȠıȠȤȒ! ȅ ıȦȜȒȞĮȢ ĮʌĮȖȦȖȒȢ țĮȚ ĲĮ țȠȜȐȡĮ ıĲİȡȑȦıȘȢ (15) įİȞ

įȚĮĲȓșİȞĲĮȚ țĮȚ ʌȡȑʌİȚ ȞĮ ĮʌȠțĲȘșȠȪȞ ȤȦȡȚıĲȐ.

41833034.fm Page 1 Monday, November 3, 2003 11:58 AM



5019 418 33034

DDT 7790

17b

4-13

17a

4 x 4x8

4 x 3,5x9,5

2 x

2,9x6,5

41833034.fm Page 2 Monday, November 3, 2003 11:58 AM



5019 418 33034

DDT 7790

Preliminary information for installing the hood:

Disconnect the power supply at the domestic main switch before carrying out electrical

connections.

Remove the grease filter/s.

Pre-assemble the three parts of the flue support bracket with 4 screws. The width X of the

bracket G must be identical to the internal width of the telescopic flue.

1. Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation

operations.

2. Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram

must match the centre line drawn on the wall, and the lower edge of the hole diagram must

match the lower edge of the hood: remember that with installation completed the bottom

of the hood must be at least 50 cm above the cooktop in case of electric cookers and 75 cm

in case of gas or mixed cookers.

3. Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark

the two external holes and drill, remove the hole diagram, insert 2 wall plugs and fix the

hood support bracket with two 5x45 mm screws.

4. Hook the hood to the bracket.

5. Adjust the distance between the hood and the wall.

6. Adjust the hood horizontally.

7. From the inside of the extraction unit, mark the holes for fixing the hood.

8. Remove the hood from the bracket.

9. Drill on the mark (Ø 8 mm - see step 10).

10.Insert 2 wall plugs.

11.Fit the flue support bracket G to the wall and against the ceiling, use the support bracket as

hole diagram (the small slot on the support must match the line drawn on the wall - step 4)

and mark 2 holes with the pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.

12.Fix the flue support bracket to the wall with two 5x45 mm screws.

13.Hook the hood to the bottom bracket.

14.Fix the hood to the wall with two 5x45 mm screws (ABSOLUTELY NECESSARY).

15.Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately)

to the collar B located above the extraction motor unit.

For extractor operation, connect the other end of the exhaust pipe to the home discharge

device. For filter operation, fix the deflector F to the flue support bracket G and connect the

other end of the exhaust pipe to the deflector collar F. Once the steam and fumes have been

filtered by the carbon filter (not provided, to be ordered separately) they are conveyed back

to the kitchen through grid H.

16.Carry out the electrical connection.

17.Apply the flues and fix them with 2 screws (20a) to the flue support G (20b).

18.Slide the bottom section of the flue in the special seat above the hood to completely cover

the extraction unit.

Refit the grease filter/s and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

D F NL EGB

P I GR

41833034.fm Page 6 Monday, November 3, 2003 11:58 AM



5019 418 33034

DDT 7790

CONTROL PANEL

Control panel calibration

When the appliance is plugged in (or after a power failure) the system calibrates the buttons;

during calibration two blinking dots will appear.

The calibration lasts for 15''.

At the end of the calibration procedure, the two dots will stop blinking and only the bottom

right dot will stay alight.

1. ON button (Stand by) / OFF extraction / Resetfilter saturation indicator:

- ON (Stand by) - the display shows a lighted dot only.

- OFF - the display is OFF: all controls, except for the light button, are disabled.

To set the hood to ON (Stand by) or OFF, press the button and wait until the dot appears or

disappears according to the required setting.

Reset filter saturation indicator. Press and hold for at least 3 seconds, an acoustic signal

will sound. The reset operation can only take place when the hood is on.

2. Light ON/OFF button.

3. Extraction speed decrease button (1, 2, 3, P-intensive).

4. Extraction speed increase button (P-intensive, 3, 2, 1).

Warning! The intensive extraction speed appears on the left of the display with the letter P and

the remaining operating time in minutes (and the blinking dot) on the right; after 5 minutes, it

automatically switches to extraction speed 2.

5. Timer button: after selecting the required extraction speed, press this button to set the

timing:

Extraction speed 1: 20 minutes

Extraction speed 2: 15 minutes

Extraction speed 3: 10 minutes

Intensive extraction speed (P): 5 minutes

The display will show the remaining operating time and the blinking dot on the right.

At the end, the hood will switch off.

Press again to disable the timing.

6. Display: shows the selected extraction speed, grease filter (F) or carbon filter (C)

saturation, Stand by mode (lighted dot) and control panel calibration (two blinking

dots).

Warning! The carbon filter saturation indicator is normally deactivated (for extractor

version - see attached instructions manual). In order to activate it (for filter operation - see

attached instructions manual), simultaneously press AND HOLD buttons 3 and 4 until C appears

on the display. To deactivate the carbon filter saturation indicator, simultaneously press AND

HOLD buttons 3 and 4: letter F will appear on the display, followed by C. The latter will

disappear after a few seconds.

12345

FIG. 1

PRODUCT SHEET

D F NL EGB

P I GR

41833034.fm Page 7 Monday, November 3, 2003 11:58 AM



5019 418 33034

DDT 7790

1. Control panel.

2. Grease filter.

3. Halogen bulbs.

4. Steam deflector.

5. Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

1. Disconnect the electrical power supply.

2. Remove the grease filters - Fig. 2: push the

spring release handle backwards (f1), then

remove the filter downwards (f2).

3. After cleaning the grease filter, remount in

reverse order ensuring the entire

extraction surface is covered.

Replacing bulbs

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other

suitable tool to prise off (m-Fig. 2) the

lamp cover (p-Fig. 2).

3. Remove the burnt-out bulb.

Replace using 20 W max halogen bulbs

only, making sure not to touch them with

your hands.

4. Close the lighting unit (snap-close).

Carbon filter Fitting and

Maintenance

Fitting the carbon filter:

1. Disconnect the electrical power supply.

2. Remove the grease filter (f1/f2 - Fig. 2).

3. Turn the side knobs 90° and then remove

the filter holder (g - Fig. 3).

4. Fit the carbon filter (h - Fig. 3) in the filter

holder (i - Fig. 3).

5. Refit the filter holder and secure it to the

hood by turning the side knobs 90°

(g - Fig. 3).

6. Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon

filter can be washed and reactivated.

With normal hood use, the filter should be

cleaned once a month. The best way to clean

the filter is in a dishwasher at the highest

temperature possible, using a normal

dishwasher detergent. To avoid particles of

food or dirt settling on the filter during

washing and giving rise to unpleasant smells,

it is advisable to wash the filter on its own.

After washing, dry the filter in the oven at

100°C for 10 minutes to reactivate it.

The filter will retain its odour-absorbing

capacity for three years, after which it must be

replaced.

FIG. 3

FIG. 2

D F NL EGB

P I GR

41833034.fm Page 8 Monday, November 3, 2003 11:58 AM

Bauknecht DDT 7790 IN Program Chart

Brand: Bauknecht

Model: DDT 7790 IN

Category: Cooker hoods

Type: Program Chart

Download PDF

report

Bauknecht DDT 7790 IN Program Chart

Bauknecht DDT 7790 IN Program Chart

Related papers

Other documents