Whirlpool AKR 958 IX WP Program Chart
- Category
- Cooker hoods
- Type
- Program Chart
The Whirlpool AKR 958 IX WP is a cooker hood with four speed settings, halogen bulbs, and a telescopic flue. It can be used for both extraction and recirculation, with a carbon filter available for purchase separately for recirculation mode. The grease filter should be cleaned at least once a month and can be washed in a dishwasher. The carbon filter can be washed and reactivated in the oven and should be replaced every three years. The halogen bulbs can be replaced with 20W max bulbs.
The Whirlpool AKR 958 IX WP is a cooker hood with four speed settings, halogen bulbs, and a telescopic flue. It can be used for both extraction and recirculation, with a carbon filter available for purchase separately for recirculation mode. The grease filter should be cleaned at least once a month and can be washed in a dishwasher. The carbon filter can be washed and reactivated in the oven and should be replaced every three years. The halogen bulbs can be replaced with 20W max bulbs.
5019 318 33088
AKR 928 - AKR 958
INSTALLATIONSBLAD
Minsta tillåtna avstånd från olika typer av spisar: 65 cm (elektrisk spis), 75 cm
(gasspis, gasolspis eller koleldad spis). Följ numreringen nedan för monteringen
(1
Ö
2
Ö
3
Ö
.....). Rökrör och fästanordningar (15) levereras inte tillsammans
med fläktkåpan utan måste köpas separat. Kontrollera att den elektriska
anslutningen av belysning och motor är utförd på korrekt sätt (2-20). Skruvarna
som används för att fästa fläktkåpans avtagbara hölje vid fläktkåpans stomme
måste dras åt ordentligt (17). Fläktkåpans hölje kan vara utformat på olika sätt,
men det skall alltid sättas på och fixeras vid kåpans underrede på samma sätt.
INSTALLASJONSVEILEDNING
Minimumsavstand til komfyrtopp: 65 cm (elektriske kokeplater), 75 cm (gass-,
parafin- eller kullkomfyr). Følg nummereringen ved montering (1
Ö
2
Ö
3
Ö
.....)
Avtrekkskanal og klemmer (15) følger ikke med og må anskaffes separat.
Kontroller at den elektriske tilkoblingen av lys og motor er korrekt (2-20). Stram
godt til skruene som holder den avtagbare skjermen (17). Skjermene kan ha
forskjellig utforming, men festes alltid til ventilatoren på samme vis.
INSTALLATIONSVEJLEDNING
Minimumafstand fra kogezoner: 65 cm (elkogezoner), 75 cm (gas-, olie- eller
kulfyrede kogezoner). Ved montering skal man følge vejledningens
nummerrækkefølge (1
Ö
2
Ö
3
Ö
.....). Aftræksrør og spændebånd (15) medfølger
ikke, men skal købes separat. Kontrollér, at motorens og lampernes elektriske
tilslutning er korrekt (2-20). Spænd skruerne, der fastgør den aftagelige
afskærmning til emhætten, godt fast (17). Afskærmningen kan have forskellige
udformninger, men monterings- og fastgørelsesproceduren til emhætten er ens.
ASENNUSOHJEET
Vähimmäisetäisyys liedestä: 65cm (sähkölevyt), 75cm (kaasu-, öljy- tai
hiililiedet). Suorita kokoonpano numerojärjestyksessä (1
Ö
2
Ö
3
Ö
.....).
Poistoputkea ja puristimia (15) ei ole toimitettu, ne on hankittava erikseen.
Tarkista, että valojen ja moottorin (2-20) sähköliitäntä on tehty oikein. Kiristä
kunnolla ruuvit, jotka kiinnittävät liesituulettimen irrotettavan suojuksen (17).
Suojus voi olla erimuotoinen, mutta tuulettimeen asennus- ja
kiinnitysmenetelmä on aina sama.
INSTALLATION SHEET
Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or
coal cookers). To install follow points (1
Ö
2
Ö
3
Ö
.....). The discharge flue and
fixing clamps (15) are not provided and must be purchased separately. Check for
correct electrical connections of lights and motor (2-20). Tighten the screws
fixing the removable casing to the hood (17). The casing can be in various
shapes, but the procedure for fitting and fixing to the hood is the same.
S
N
DK
FIN
GB
31833088.fm Page 1 Friday, October 10, 2003 4:46 PM
5019 318 33088
AKR 928 - AKR 958
2
1
X
=
=
X
G
=
=
X
F
31833088.fm Page 2 Friday, October 10, 2003 4:46 PM
5019 318 33088
AKR 928 - AKR 958
21b
14
19b
19b
7
7
3
4
6
8
9
12
12
13
15
Ø 150
19a
9
8
16
8
9
10
11
21a
21a
21b
19a
20
18
18
18
5
17
F
G
H
B
31833088.fm Page 3 Friday, October 10, 2003 4:46 PM
AKR 928 - AKR 958
5019 318 33088
INSTALLATION - ASSEMBLY INSTRUCTIONS
Preliminary information for installing the hood
Before starting installation, disconnect the power supply at the home main switch.
Remove the grease filter/s and the carbon filter holder.
1.
Pre-assemble the three parts of the flue support bracket with 4 screws; the width
X
of the bracket
G
must
be identical to the internal width of the telescopic flue.
For filter version only
:
Pre-assemble the three parts of the deflector with 2 screws; the width
X
of the deflector
F
must be
identical to the internal width of the telescopic flue.
2.
Place the extraction unit on a flat surface and fit the bottom part of the hood on it.
Secure it with 4 screws.
Model AKR 958 only
Carry out the electrical connections between the two parts.
3.
Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.
4.
Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the
centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the
hood.
Remember that with installation completed the bottom of the hood must be at least 50 cm above the hob
in case of electric cookers and 75 cm in case of gas or mixed cookers.
5.
Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two
external holes and drill, remove the hole diagram.
6.
Insert 2 wall plugs and fix the hood support bracket with two 5x45 mm screws.
7.
Hook the hood to the bracket.
8.
Adjust the distance between the hood and the wall.
9.
Adjust the hood horizontally.
10.
From the inside of the extraction unit, mark the holes for fixing the hood (to do so, remove the filter
holder; refit it after fixing the hood).
11.
Remove the hood from the bracket and drill on the mark (Ø 8 mm - see step 10). Insert 1 wall plug.
12.
Fit the flue support bracket
G
to the wall and against the ceiling, use the support bracket as hole diagram
(the small slot on the support must match the line drawn on the wall - step 3) and mark 2 holes with the
pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.
13.
Fix the flue support bracket to the wall with two 5x45 mm screws.
14.
Hook the hood to the bottom bracket. Fix the hood to the wall with a 5x45mm screw (ABSOLUTELY
NECESSARY).
15.
Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar
B
located above the extraction motor unit.
For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter
operation, fix the deflector
F
to the flue support bracket
G
with 4 screws and connect the other end of
the exhaust pipe to the deflector collar
F
(if the collar is not already fitted it should be inserted on the
deflector and secured with 1 screw). Once the steam and fumes have been filtered by the carbon filter
(not provided, to be ordered separately) they are conveyed back to the kitchen through grid
H
.
16.
Carry out the electrical connection.
17.
Fit the casing on the runners.
18.
Fix the casing to the hood with 4 screws
19.
Apply the flues and fix them with 2 screws (
19a
) to the flue support
G
(
19b
).
20. Model AKR 928 only
: Carry out the electrical connections between the two parts.
21.
Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction
unit and fix it to the hood (
21a
) with 2 screws (
22b
).
Refit the grease filter/s and the carbon filter holder, and check for correct hood operation.
S
N DK
FIN
GB
31833088.fm Page 13 Friday, October 10, 2003 4:46 PM
5019 318 33088
AKR 928 - AKR 958
1.
Control panel.
a.
Light ON/OFF switch.
b.
Extraction and minimum extraction speed ON/
OFF switch.
c.
Medium extraction speed switch.
d.
Maximum extraction speed switch.
2.
Grease filter.
3.
Halogen bulbs.
4.
Steam deflector.
5.
Telescopic flue.
To clean the grease filter
Wash the grease filter at least once a month.
1.
Disconnect the electrical power supply.
2.
Remove the grease filters -
Fig. 1
:
AKR 928
... pull the spring release handle (
f
) downwards,
then remove the filter.
AKR 958
... push the spring release handle backwards (
f1
),
then remove the filter downwards (
f2
).
3.
After cleaning the grease filter refit in reverse
order, making sure the entire extraction surface is
covered.
Replacing bulbs
1.
Disconnect the electrical power supply.
2.
Use a small screwdriver or any other suitable tool
to prise off (
m-Fig. 2
) the lamp cover (
p-Fig. 2
).
3.
Remove the burnt-out bulb.
Use 20W max halogen bulbs only, taking care not
to touch them with your hands.
4.
Close the lighting unit (snap-close).
Carbon filter Fitting and Maintenance
Fitting the carbon filter:
1.
Disconnect the electrical power supply.
2.
Remove the grease filter (
Fig. 1
).
3.
Turn the side knobs 90° and then remove the filter
holder (
g - Fig. 3
).
4.
Fit the carbon filter (
h - Fig. 3
) in the filter holder
(i - Fig. 3
).
5.
Refit the filter holder and secure it to the hood
with the screw (
g - Fig. 3
).
6.
Refit the grease filter.
Fitting the carbon filter:
Unlike traditional carbon filters, this carbon filter can
be washed and reactivated.
With normal hood use, the filter should be cleaned
once a month. The best way to clean the filter is in a
dishwasher at the highest temperature possible, using
a normal dishwasher detergent. To avoid particles of
food or dirt settling on the filter during washing and
giving rise to unpleasant smells, it is advisable to wash
the filter on its own. After washing, dry the filter in the
oven at 100°C for 10 minutes to reactivate it.
The filter will retain its odour-absorbing capacity for
three years, after which it must be replaced.
4
5
2
3
ab
c
d
1
3
1
a
b
c
d
h
i
g
g
g
g
m
p
f
f1
f2
Fig. 1
Fig. 2
Fig. 3
AKR 928
AKR 958
AKR 958
AKR 928
PRODUCT SHEET
31833088.fm Page 14 Friday, October 10, 2003 4:46 PM
-
1
-
2
-
3
-
4
-
5
Whirlpool AKR 958 IX WP Program Chart
- Category
- Cooker hoods
- Type
- Program Chart
The Whirlpool AKR 958 IX WP is a cooker hood with four speed settings, halogen bulbs, and a telescopic flue. It can be used for both extraction and recirculation, with a carbon filter available for purchase separately for recirculation mode. The grease filter should be cleaned at least once a month and can be washed in a dishwasher. The carbon filter can be washed and reactivated in the oven and should be replaced every three years. The halogen bulbs can be replaced with 20W max bulbs.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- dansk: Whirlpool AKR 958 IX WP
Related papers
-
Whirlpool AKR 948 IX Program Chart
-
Whirlpool AKR 958 IX WP Program Chart
-
-
-
Whirlpool AKR 950 IX WP Program Chart
-
-
-
-
Whirlpool AKR 631 IX WP Program Chart
-
Whirlpool DBRI 6910/01 IN User guide