Whirlpool AKR 958 IX WP Program Chart

Category
Cooker hoods
Type
Program Chart

The Whirlpool AKR 958 IX WP is a kitchen hood that offers a range of features to help keep your kitchen air clean and fresh. With four extraction speed settings, you can choose the right level of power for your cooking needs. The halogen bulbs provide bright illumination for your cooking area, while the grease filter helps to trap grease and particles from cooking vapors. Additionally, the carbon filter helps to eliminate odors from cooking, leaving your kitchen smelling fresh and clean.

The Whirlpool AKR 958 IX WP is a kitchen hood that offers a range of features to help keep your kitchen air clean and fresh. With four extraction speed settings, you can choose the right level of power for your cooking needs. The halogen bulbs provide bright illumination for your cooking area, while the grease filter helps to trap grease and particles from cooking vapors. Additionally, the carbon filter helps to eliminate odors from cooking, leaving your kitchen smelling fresh and clean.

5019 318 33090
AKR 928 - AKR 958
KARTA INSTALACYJNA
Minimalna odległość od palników: 65 cm (palniki elektryczne), 75 cm
(palniki gazowe, olejowe lub węglowe). Podczas montażu należy
przestrzegać kolejności numeracji (1
Ö
2
Ö
3
Ö
.....). Rura odprowadzająca
oraz wsporniki (15) nie są dostarczane i należy je zakupić oddzielnie.
Sprawdzić, czy światełka i silni zostały prawidłowo podłączone do prądu
(2-20). Mocno dokręcić śruby mocujące zejmowaną pokrywę okapu (17).
Pokrywa może mieć różną formę, lecz procedura zakładania i
zamocowania w okapie jest taka sama.
POPIS INSTALACE
Minimální vzdálenost od sporáků: 65 cm (elektrické sporáky), 75 cm
(sporáky na plyn, naftu nebo uhlí). Při montáži sledujte číslování
(1
Ö
2
Ö
3
Ö
.....). Odvodní trubka a pásky k upevnění (15) nejsou součástí
vybavení, musíte je zakoupit. Zkontrolujte správné elektrické připojení
světel a motoru (2-20). Pevně utáhněte šrouby, kterými je připevněn k
digestoři snímatelný plášt' (17). Plášt' může mít různý tvar, ale způsob
zasunutí a upevnění k digestoři zůstává stejný,
INŠTALAČNÁ SCHÉMA
Minimálna vzdialenost' od sporáka: 65 cm (elektrické sporáky), 75 cm
(plynové sporáky, sporáky na naftu alebo uhlie). Pri montáži postupujte
podľa číslic (1
Ö
2
Ö
3
Ö
.....). Rúra na odvádzanie dymov a upevňovacie
svorky (15) sa nedodávajú, musíte ich kúpit' samostatne. Skontrolujte
správnost' elektrického zapojenia osvetlenia a motora (2-20). Pevne
utiahnite skrutky, ktoré držia odnímateľné opláštenie odsávača pár (17).
Opláštenie môže mat' rôzne formy, montážny postup a upevnenie na
odsávač pár sú však rovnaké.
ÜZEMBE HELYEZÉSI ÚTMUTATÓ
A tűzhelytől való minimális távolság: 65 cm (elektromos tűzhely), 75 cm
(gáz-, olaj- vagy széntüzelésű tűzhely). A felszereléshez kövesse a
számozást (1
Ö
2
Ö
3
Ö
.....). Az elvezetőcső és a rögzítőbilincsek (15) nem
tartozékok, így azokat külön kell megvásárolni. Ellenőrizze a lámpák és a
motor elektromos bekötésének helyességét (2-20). Határozottan húzza
meg a levehető köpenyt a készülékhez rögzítő csavarokat (17). A köpeny
különböző formájú lehet ugyan, de a beillesztés és a készülékhez való
rögzítés folyamata változatlan.
PL
CZ
SK
H
31833090.fm Page 1 Thursday, October 30, 2003 11:57 AM
5019 318 33090
AKR 928 - AKR 958
ÑÕÅÌÀ ÓÑÒÀÍÎÂÊÈ
Ìèíèìàëüíîå ðàññòîÿíèå äî êîíôîðîê: 65 ñì (ýëåêòðè÷åñêèå
êîíôîðêè), 75 ñì (êîíôîðêè ãàçîâûå, êåðîñèíîâûå èëè
óãîëüíûå). Ïîñëåäîâàòåëüíîñòü äåéñòâèé ïðè ìîíòàæå äîëæíà
ñîîòâåòñòâîâàòü íóìåðàöèè (1
Ö
2
Ö
3
Ö
.....). Âûïóñêíàÿ òðóáà è
êðåïåæíûå çàæèìû (15) íå âõîäÿò â êîìïëåêò ïîñòàâêè è
ïðèîáðåòàþòñÿ îòäåëüíî. Ïðîâåðüòå ïðàâèëüíîñòü ïîäêëþ÷åíèÿ
ê ýëåêòðîñåòè îñâåòèòåëüíûõ ïðèáîðîâ è äâèãàòåëÿ (2-20).
Ïëîòíî çàòÿíèòå âèíòû, êîòîðûìè êðåïèòñÿ ê âûòÿæêå ñúåìíîå
ïîêðûòèå (17). Ñúåìíîå ïîêðûòèå ìîæåò èìåòü ðàçëè÷íóþ
ôîðìó, îäíàêî ïðîöåäóðà óñòàíîâêè è êðåïëåíèÿ ê âûòÿæêå
îñòàåòñÿ íåèçìåííîé.
ÊÀÐÒÀ ÇÀ ÈÍÑÒÀËÈÐÀÍÅ
Ìèíèìàëíî ðàçñòîÿíèå îò ïå÷êè: 65 ñì (åëåêòðè÷åñêè ïå÷êè),
75 ñì (ïå÷êè ñ ãàç, íàôòà èëè âúãëèùà). Çà ìîíòàæ ñëåäâàéòå
íîìåðàöèÿòà (1
Ö
2
Ö
3
Ö
.....). Òðúáàòà çà îòâåæäàíå è ñêîáèòå çà
ôèêñèðàíå (15) íå ñà âêëþ÷åíè â êîìïëåêòà è òðÿáâà äà ñå
çàêóïÿò îòäåëíî. Ïðîâåðåòå ïðàâèëíîòî ñâúðçâàíå êúì
åëåêòðè÷åñêàòà ìðåæà íà îñâåòëåíèåòî è ìîòîðà (2-20).
Çàòåãíåòå äîêðàé âèíòîâåòå, êîèòî ôèêñèðàò ïîäâèæíèÿ êîðïóñ
íà àñïèðàòîðà (17). Êîðïóñúò ìîæå äà èìà ðàçëè÷íà ôîðìà, íî
ïðîöåäóðàòà íà ïîñòàâÿíå è ôèêñèðàíå íà àñïèðàòîðà îñòàâà
åäíà è ñúùà.
FIȘA DE INSTALARE
Distanţa minimă de la arzătoare: 65 cm (arzătoare electrice), 75 cm
(arzătoare pe bază de gaze, motorină sau cărbune). Pentru montaj urmaţi
numerotarea (1
Ö
2
Ö
3
Ö
.....). Tubul de evacuare și manșoanele de fixare
(15) nu fac parte din dotare și trebuie să fie cumpărate separat. Controlaţi
racordarea electrică corectă a becurilor și a motorului (2-20). Strângeţi
bine șuruburile care fixează etajera detașabilă de hotă (17). Etajera poate
avea forme diferite, dar procedura de inserare și de fixare de hotă rămâne
aceeași.
INSTALLATION SHEET
Minimum height above cooker: 65 cm (electric cookers), 75 cm (gas, gas oil or
coal cookers). To install follow points (1
Ö
2
Ö
3
Ö
.....). The discharge flue and
fixing clamps (15) are not provided and must be purchased separately. Check for
correct electrical connections of lights and motor (2-20). Tighten the screws
fixing the removable casing to the hood (17). The casing can be in various
shapes, but the procedure for fitting and fixing to the hood is the same.
RUS
BG
RO
GB
31833090.fm Page 2 Thursday, October 30, 2003 11:57 AM
5019 318 33090
AKR 928 - AKR 958
2
1
X
=
=
X
G
=
=
X
F
31833090.fm Page 3 Thursday, October 30, 2003 11:57 AM
5019 318 33090
AKR 928 - AKR 958
21b
14
19b
19b
7
7
3
4
6
8
9
12
12
13
15
Ø 150
19a
9
8
16
8
9
10
11
21a
21a
21b
19a
20
18
18
18
5
17
F
G
H
B
31833090.fm Page 4 Thursday, October 30, 2003 11:57 AM
5019 318 33090
AKR 928 - AKR 958
INSTALLATION - ASSEMBLY INSTRUCTIONS
Preliminary information for installing the hood
Before starting installation, disconnect the power supply at the home main switch.
Remove the grease filter/s and the carbon filter holder.
1.
Pre-assemble the three parts of the flue support bracket with 4 screws; the width
X
of the bracket
G
must
be identical to the internal width of the telescopic flue.
For filter version only
Pre-assemble the three parts of the deflector with 2 screws; the width
X
of the deflector
F
must be
identical to the internal width of the telescopic flue.
2.
Place the extraction unit on a flat surface and fit the bottom part of the hood on it.
Secure it with 4 screws.
Model AKR 958 only
Carry out the electrical connections between the two parts.
3.
Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.
4.
Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the
centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the
hood.
Remember that with installation completed the bottom of the hood must be at least 50 cm above the hob
in case of electric cookers and 75 cm in case of gas or mixed cookers.
5.
Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two
external holes and drill, remove the hole diagram.
6.
Insert 2 wall plugs and fix the hood support bracket with two 5x45 mm screws.
7.
Hook the hood to the bracket.
8.
Adjust the distance between the hood and the wall.
9.
Adjust the hood horizontally.
10.
From the inside of the extraction unit, mark the holes for fixing the hood (to do so, remove the filter
holder; refit it after fixing the hood).
11.
Remove the hood from the bracket and drill on the mark (Ø 8 mm - see step 10). Insert 1 wall plug.
12.
Fit the flue support bracket
G
to the wall and against the ceiling, use the support bracket as hole diagram
(the small slot on the support must match the line drawn on the wall - step 3) and mark 2 holes with the
pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.
13.
Fix the flue support bracket to the wall with two 5x45 mm screws.
14.
Hook the hood to the bottom bracket. Fix the hood to the wall with a 5x45mm screw (ABSOLUTELY
NECESSARY).
15.
Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar
B
located above the extraction motor unit.
For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter
operation, fix the deflector
F
to the flue support bracket
G
with 4 screws and connect the other end of
the exhaust pipe to the deflector collar
F
(if the collar is not already fitted it should be inserted on the
deflector and secured with 1 screw). Once the steam and fumes have been filtered by the carbon filter
(not provided, to be ordered separately) they are conveyed back to the kitchen through grid
H
.
16.
Carry out the electrical connection.
17.
Fit the casing on the runners.
18.
Fix the casing to the hood with 4 screws.
19.
Apply the flues and fix them with 2 screws (
19a
) to the flue support
G
(
19b
).
20. Model AKR 928 only
: Carry out the electrical connections between the two parts.
21.
Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction
unit and fix it to the hood (
21a
) with 2 screws (
22b
).
Refit the grease filter/s and the carbon filter holder, and check for correct hood operation.
PL SK H RUS
CZ
BG RO GB
31833090.fm Page 19 Thursday, October 30, 2003 11:57 AM
5019 318 33090
AKR 928 - AKR 958
1.
Control panel.
a.
Light ON/OFF switch.
b.
Extraction and minimum extraction speed
ON/OFF switch.
c.
Medium extraction speed switch.
d.
Maximum extraction speed switch.
2.
Grease filter.
3.
Halogen bulbs.
4.
Steam deflector.
5.
Telescopic flue.
To clean the grease filter
Wash the grease filter at least once a month.
1.
Disconnect the electrical power supply.
2.
Remove the grease filters -
Fig. 1
:
AKR 928
... pull the spring release handle (
f
) downwards,
then remove the filter.
AKR 958
... push the spring release handle backwards (
f1
),
then remove the filter downwards (
f2
).
3.
After cleaning the grease filter refit in reverse
order, making sure the entire extraction surface
is covered.
Replacing bulbs
1.
Disconnect the electrical power supply.
2.
Use a small screwdriver or any other suitable tool
to prise off (
m-Fig. 2
) the lamp cover (
p-Fig. 2
).
3.
Remove the burnt-out bulb.
Use 20W max halogen bulbs only, taking care not
to touch them with your hands.
4.
Close the lighting unit (snap-close).
Carbon filter Fitting and Maintenance
Fitting the carbon filter:
1.
Disconnect the electrical power supply.
2.
Remove the grease filter (
Fig. 1
).
3.
Turn the side knobs 90° and then remove the
filter holder (
g - Fig. 3
).
4.
Fit the carbon filter (
h - Fig. 3
) in the filter
holder
(
i - Fig. 3
).
5.
Refit the filter holder and secure it to the hood
with the screw (
g - Fig. 3
).
6.
Refit the grease filter.
Fitting the carbon filter:
Unlike traditional carbon filters, this carbon filter can
be washed and reactivated.
With normal hood use, the filter should be cleaned
once a month. The best way to clean the filter is in a
dishwasher at the highest temperature possible,
using a normal dishwasher detergent. To avoid
particles of food or dirt settling on the filter during
washing and giving rise to unpleasant smells, it is
advisable to wash the filter on its own. After
washing, dry the filter in the oven at 100°C for 10
minutes to reactivate it.
The filter will retain its odour-absorbing capacity for
three years, after which it must be replaced.
4
5
2
3
ab
c
d
1
3
1
a
b
c
d
h
i
g
g
g
g
m
p
f
f1
f2
Fig. 1
Fig. 2
Fig. 3
AKR 928
AKR 958
AKR 958
AKR 928
PRODUCT SHEET
PL SK H RUS
CZ
BG RO GB
31833090.fm Page 20 Thursday, October 30, 2003 11:57 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Whirlpool AKR 958 IX WP Program Chart

Category
Cooker hoods
Type
Program Chart

The Whirlpool AKR 958 IX WP is a kitchen hood that offers a range of features to help keep your kitchen air clean and fresh. With four extraction speed settings, you can choose the right level of power for your cooking needs. The halogen bulbs provide bright illumination for your cooking area, while the grease filter helps to trap grease and particles from cooking vapors. Additionally, the carbon filter helps to eliminate odors from cooking, leaving your kitchen smelling fresh and clean.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages