Bauknecht DDTI 5950 IN COOKERHO Program Chart

Brand: Bauknecht

Model: DDTI 5950 IN COOKERHO

Category: Cooker hoods

Type: Program Chart

The Bauknecht DDTI 5950 IN COOKERHO is a versatile cooking appliance that combines a sleek design with advanced features to enhance your culinary experience. With its induction hob, you can enjoy precise temperature control and rapid heating, allowing you to cook your meals quickly and efficiently. The oven offers a variety of cooking functions, including fan-assisted cooking, grilling, and defrosting, providing you with the flexibility to prepare a wide range of dishes.

5019 418 33074

Respect the following minimum distances from the cooktop: 50 cm (electric cookers), 65 cm (gas cookers). If the

installation instructions for the gas cooker specify a greater distance, this must be taken into account. The fume

hose and hose clamps are not supplied. We recommend that you contact a qualified engineer to have the hood

installed.

Preliminary information for installing the hood:

Expansion plugs are provided to secure the hood to most types of ceilings. A qualified technician is needed, however, to make

sure that the plugs are suitable for your ceiling. The ceiling must be strong enough to take the weight of the hood.

Disconnect the power supply at the home main switch during electrical connections.

Adjust extension of the hood support structure, as the final height of the hood depends on this, and remember that with

installation completed the hood must be at least 50 cm above the hob in case of electric cookers and 65 cm in case of

gas or mixed cookers.

Fix the two sections of the structure using 8 screws.

Place the ceiling hole diagram directly above the cooktop (the centre of the diagram must match the centre of the

cooktop and the edges must be parallel to the sides of the cooktop - the side of the diagram with the wording FRONT

corresponds to the control panel side). Prepare the electrical connection.

Drill as shown (6 holes for 6 wall plugs - 4 plugs for hooking), screw the 4 outer screws leaving a space of about 1 cm

between the screw head and the ceiling.

Fit an exhaust pipe inside the truss and connect it to the collar of the motor compartment (exhaust pipe and clamps are

not provided).

Hook the truss to the 4 screws (see step 4).

CAUTION! The side of the truss with connection box corresponds to the side of the control panel with hood assembled.

Tighten the 4 screws.

Insert and tighten another 2 screws in the remaining free holes for secure fixing.

Carry out the electrical connection to the mains power supply, only turn on the power supply with assembly completed.

Extractor Version:

steam and fumes are exhausted to the outside through a discharge pipe fixed to the collar located on

the top of the hood.

Caution!

If the hood is equipped with a carbon filter, this must be removed.

The discharge air must not be ducted to a flue used for removing fumes produced by appliances using gas or other fuels, but

must have a separate outlet. All national regulations governing extraction of fumes must be observed.

10.

For extractor operation (

10 A

), connect the other end of the exhaust pipe to the home discharge device.

Filter Hood

: Air is filtered through a carbon filter and returned to the room.

Caution!

If the hood is not equipped with a carbon filter, one must be ordered and fitted prior to use.

For filter operation (

10 F

), fit the deflector

on the truss and fix it with 4 screws to the special bracket. Finally, connect the

exhaust pipe to the collar located on the deflector.

11.

Fit the nuts with fixing hooks supplied inside the top and bottom sections of the flues at the rectangular slots. A total of

12 nuts must be fitted.

12.

Join the two top sections of the flue to cover the truss so that one of the slots on the sections is situated on the same

side of the control panel and the other on the opposite side.

Screw the two sections with 6 screws (3 each side - see the plan diagram for joining the two sections).

13.

Fix the top flue assembly to the truss, near the ceiling, with 4 screws (2 each side).

14.

Joint the two bottom sections of the flue: position the rear section first and connect up the light panel; then position the

front section and connect the light panel and the controls.

15.

Fix the two bottom sections of the flue, using 6 screws (3 each side - also see the plan diagram for joining the two

sections) plus 4 screws to fasten the flues to the structure (

15 A

). ABSOLUTELY ESSENTIAL!

16.

Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION! THE BOTTOM FLUE TABS ARE

THE NARROWER AND SHALLOWER ONES.

The wider and deeper tabs are those used for the top flue, and must be cut to size.

17.

Turn the mains power on again at the central electrical panel and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

D F NL E

P IGR

41833074.fm Page 7 Monday, December 12, 2005 4:31 PM

5019 418 33074

D F NL E

P IGR

41833074.fm Page 8 Monday, December 12, 2005 4:31 PM

5019 418 33074

D F NL E

P IGR

41833074.fm Page 9 Monday, December 12, 2005 4:31 PM

5019 418 33074

D F NL E

P IGR

41833074.fm Page 10 Monday, December 12, 2005 4:31 PM

5019 418 33074

D F NL E

P IGR

To clean the grease filter

Wash the grease filter at least once a month.

Disconnect the electrical power supply.

Remove the grease filters -

Fig. 2

: pull the spring release

handle

(f)

downwards, then remove the filter.

After cleaning the grease filter refit in reverse order,

making sure the entire extraction surface is covered.

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

Disconnect the electrical power supply.

Remove the grease filter

(f - Fig. 2)

Turn the side knobs 90° and then remove the filter

holder

(g - Fig. 3)

Fit the carbon filter

(h - Fig. 3)

in the filter holder

(i - Fig. 3)

Refit the filter holder and secure it to the hood with the

screw

(g - Fig. 3)

Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can be

washed and reactivated.

With normal hood use, the filter should be cleaned once a

month. The best way to clean the filter is in a dishwasher at

the highest temperature possible, using a normal dishwasher

detergent. To avoid particles of food or dirt settling on the

filter during washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After washing, dry the

filter in the oven at 100° C for 10 minutes to reactivate it.

The filter will retain its odour-absorbing capacity for three

years, after which it must be replaced.

Replacing bulbs

Disconnect the electrical power supply.

Press on the lighting unit and open it completely

(

Fig. 4

) otherwise it will not close again.

Remove the burnt-out bulb.

Replace using 20 W max halogen bulbs only, making

sure not to touch them with your hands.

Close the lighting unit.

CONTROL PANEL

OFF/Stand-by button

Press for 3 seconds to enable all functions

(Stand-by - Led L1 on).

Press again for 3 seconds to turn off.

Light ON/OFF button

Press this to turn the lights on and off, even when the

hood is in the OFF position.

Press for one second to turn the courtesy light on; press

again for one second to turn it off.

Decrease speed button

Press this button to decrease the speed from 4 to 1.

Increase speed button

Press this button to pass from stand-by to speeds 1, 2, 3

and 4. The fourth speed has a 5 minute timer, after

which the hood will revert to stand-by.

Control panel.

Grease filter.

Halogen lamps.

Telescopic flue.

Fig. 1

Fig. 3

Fig. 4

Fig. 2

PRODUCT SHEET

41833074.fm Page 11 Monday, December 12, 2005 4:31 PM

5019 418 33074

D F NL E

P IGR

SAFEGUARDING THE

ENVIRONMENT

1. Packaging

Packaging materials are 100% recyclable and are marked with the

recycling symbol .Dispose of the appliance in conformity with

local environmental regulations. Packaging materials can be

dangerous for children. Keep packaging materials (plastic bags,

polystyrene, etc.) well out of their reach.

2. Product

This appliance is marked in compliance with European Directive

2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is scrapped suitably, you can help

prevent potentially damaging consequences for the environment

and health.

The symbol on the appliance or accompanying documentation

indicates that this product should not be disposed of as unsorted

municipal waste but must be taken to a collection point for the

treatment of WEEE.

Disposal must be carried out in accordance with local environmental

regulations for waste disposal.

For further information on the treatment, recovery and recycling of

this appliance, contact your competent local authority, the collection

service for household waste or the shop where you purchased the

appliance.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

WARNING!

• Do not allow children or infirm persons to operate the

appliance without supervision.

• Make sure children do not play with the appliance.

1. Do not connect the appliance to the mains electricity supply

until installation is completed. Always disconnect the hood

from the mains before performing any cleaning or

maintenance.

2. Do not “flambé” food under the hood. Naked flames could

cause a fire.

3. Do not leave pans unattended when frying. Cooking oil can

catch fire.

4. Regular cleaning and maintenance is essential to correct

functioning and good performance. Regularly remove dirt

deposits. Regularly clean or replace filters. Never use

flammable materials as hoses for extracted air.

5. If the hood is used together with non-electrically powered

appliances, ambient negative pressure must not exceed 4Pa

(4 x 10

-5

bars). Make sure the room is adequately ventilated.

Electrical connections

Before connecting the hood to the power supply, make sure the

voltage specified on the dataplate matches that in your home. The

dataplate is located inside the hood behind the grease filter.

If the appliance is fitted with a power cable and plug, the plug must

be placed in an accessible position.

If the hood does not come pre-fitted with a mains plug, fit one that

conforms to applicable standards or use a double-pole switch with a

minimum breaking gap of 3 mm.

Replacement of the power supply cable with power plug or flexible

cable may only be carried out by an authorized Service Centre or a

qualified electrician.

Cleaning the hood

Warning!

Failure to remove oil and grease (at least once a month)

could lead to fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

Please read these instructions carefully and keep them for future

reference, in order to ensure best use of your hood.

Packaging materials can be dangerous for children. Keep packaging

materials (plastic bags, polystyrene, etc.) well out of their reach.

Make sure the hood has not been damaged during transport.

Installation, electrical connections and replacement of the power

cable with plug or flexible cable must be carried out by a qualified

technician in compliance with the current local regulations.

Declaration of conformity

This product has been designed, manufactured and sold in

conformity to the following standards:

- safety objectives of the “Low Voltage” Directive

73/23/EEC

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC.

Troubleshooting guide

The hood does not work:

• Is the plug properly inserted in the power socket?

• Is there a power failure?

• Is the fuse blown?

The hood is not extracting efficiently:

• Is the right speed selected?

• Do the filters need cleaning or replacing?

• Are the air outlets blocked?

The light does not work:

• Does the bulb need replacing?

• Is the bulb correctly fitted?

• Is the fuse blown?

AFTER-SALES SERVICE

Before calling the After-sales Service

1. Check if you can fix the problem yourself (see "Troubleshooting

guide").

2. Switch the hood off and then on again to check if the problem

has gone.

3. If the problem persists, contact the After-sales Service.

Specify:

• the nature of the problem,

• the model of hood, stated on the data plate inside the hood,

accessible by removing the grease filters.

• your full address,

• your telephone number and area code.

• the service code (the number appearing below the word

SERVICE on the data plate inside the hood behind the grease

filter).

If any repairs are needed, contact an authorised Service Centre (to

ensure that only original spare parts are used and that repairs are

made correctly).

Failure to comply with these instructions may compromise the

safety and quality of the product.

41833074.fm Page 12 Monday, December 12, 2005 4:31 PM

Bauknecht DDTI 5950 IN COOKERHO Program Chart

Brand: Bauknecht

Model: DDTI 5950 IN COOKERHO

Category: Cooker hoods

Type: Program Chart

Download PDF

report

Bauknecht DDTI 5950 IN COOKERHO Program Chart

Bauknecht DDTI 5950 IN COOKERHO Program Chart

Related papers

Other documents