Rev. 230605
i3-TRNG-CAMS-B79T.indd
Angle Mount Camera Bracket for M79
B79T
User Manual
Scan this QR code or visit ftp.i3international.com to view
i3 product manuals.
Contact our Technical Support team at: 1.877.877.7241 or
concerns regarding camera installation or if you require
software services or support.
QR Code for Complete
User Manual and ACT
The B79T is an tilt angle mount back box for cable management and can be used for
surface or horizontal wall mounting of i3’s M79 fisheye camera model.
• Tilt bracket for M79 Fisheye camera for best Panoramic view, ideal for wall mounting
• Back box for IP camera wire management.
• Suitable for outdoor and indoor installations.
• Six (6) pre-drilled hole dimples for surface mounting.
PACKAGE CONTENTS
In addition to this manual and B79T back box,
the packing box includes:
1. Round head screw, machine type x3
2. Round head screw, tapping type with O-ring x4
3. Plastic anchor x4
4. Surface Mount template x1
DIMENSIONS
INSTALLATION NOTES
• Ensure that the mounting surface and mounting hardware is suitable for the
chosen installation method.
• To maintain IP67 waterproof rating, always use the waterproof RJ45
connector supplied with the camera.
• Always add sealant to all threads in outdoor installations.
• Use a network cable 5mm or more in diameter to create a good seal in RP1.
• Tighten the provided tapping screws to fully compress the ‘O’ ring.
SURFACE INSTALLATION
Use the security Torx bit or screwdriver (not provided) to loosen four screws
securing the dome bubble to the M79 camera. Set the dome bubble aside.
1. B79T comes with six 90% pre-drilled hole dimples. Depending on the type of
installation and mounting surface, complete drilling 2-3 holes.
2. Attach the mounting template (4) to the mounting surface.
3. Drill holes in the mounting surface, as marked on the template, to match the
pre-drilled B79T holes.
4. Insert anchors (3) into the holes.
5. Drill the conduit hole for the camera cable, as marked on the template.
6. Secure the B79T back box to the mounting surface using the tapping screws
with the O-ring (2).
Tighten to fully compress the ‘O’ ring.
7. Pull the camera’s cable into the B79T back box.
8. Use the round head machine screws (1) to secure the camera base to the
back box.
9. Re-attach the dome bubble.
Figure B. Main parts, dimensions
3
12
Up
Lens Direction
GUIDE PATTERN
4
Cable retention clip
Diameter 5 1/8” (130 mm)
1 1/8” (28 mm)
2 1/16” (52 mm)
RP1. 3/4” waterproof
rubber plug
Rubber gasket
Lens Direction
GUIDE PATTERN
Figure C. Attaching B79T to the mounting surface.
• Attach the mounting template to the mounting surface.
• Drill holes in the mounting surface to match the holes in B79T.
• Insert plastic anchors into the holes in the mounting surface.
• Drill the conduit hole for the camera cable.
• Secure B79T to the mounting surface using the tapping screws
with the O-ring. Tighten to fully compress the ‘O’ ring.
Figure A. Accessories
Figure D. Attaching M79 to B79T
• Pull the camera’s
cable into the
B79T.
• Secure M79T
to B79T using
the round head
machine screws.
Figure E. Attaching M79 dome bubble
• Re-attach the dome bubble.
Figure F. Complete Installation.
1
i3 International B79 User manual
i3 International M79 User manual
i3 International B88 User manual
i3 International b77 User manual
i3 International Ax88 User manual
i3-TECHNOLOGIES i3-TECHNOLOGIES Am73 5MP Outdoor IR HD Analog Dome User manual
Pelco Evolution 12 Camera Range Installation guide
Hikvision DS-2CD4132F-Z Installation guide
Tyco Illustra Pro series Quick start guide
Avigilon H6SL Dome Camera Installation guide
Aritech TruVision TVF-1104 User manual
Avigilon 1.3C-H5SL-D1 Installation guide