i3 International B88 User manual

B88
i3 International
Brand
i3 International
Model
B88
Category
Security camera accessories
Type
User manual

i3 International B88 is an extension back box designed for cable management and mounting of i3's Ax88 12MP Fisheye camera. It features six pre-drilled hole dimples for surface mounting and can be used for outdoor and indoor installations. The B88 provides a waterproof solution with an IP67 rating when used with the included waterproof RJ45 connector and sealant. It also allows for flexible mounting options with the DB60 Horizontal Wallmount bracket or Pendant Mount EMT Pipe (sold separately).

i3 International B88 is an extension back box designed for cable management and mounting of i3's Ax88 12MP Fisheye camera. It features six pre-drilled hole dimples for surface mounting and can be used for outdoor and indoor installations. The B88 provides a waterproof solution with an IP67 rating when used with the included waterproof RJ45 connector and sealant. It also allows for flexible mounting options with the DB60 Horizontal Wallmount bracket or Pendant Mount EMT Pipe (sold separately).

i3-TRNG-CAMS-B88.indd
Rev. 220223
The B88 is an extension back box for cable management and can be used for surface,
pendant or horizontal wall mounting of i3’s Ax88 12MP Fisheye camera.
• Back box for IP camera wire management.
• Suitable for outdoor and indoor installations.
• Six (6) pre-drilled hole dimples for surface mounting. Optional use with Pendant
Mount EMT Pipe 3/4” or DB60 Horizontal Wallmount bracket.
PACKAGE CONTENTS
In addition to this manual and B88 back box,
the packing box includes:
1. Round head screw, machine type x4
2. Round head screw, tapping type with O-ring x3
3. Plastic anchor x3
4. Surface Mount template x1
Back Box Mounting Base
B88
User Manual
DIMENSIONS
Pendant Mount
Rigid 3/4” EMT Pipe
(Optional)
DB60 Goose Neck
Wallmount Bracket
(Optional)
Add Sealant
Alignment
marks
Ax88
Camera
3/4” Electrical
EMT Conduit
Fitting
Scan this QR code or visit ftp.i3international.com to view i3
product manuals.
Contact our Technical Support team at: 1.877.877.7241 or
[email protected] if you have any questions or
concerns regarding camera installation or if you require
software services or support.
QR Code for Complete
User Manual and ACT
INSTALLATION NOTES
• In outdoor installations, remove RP1, add silicone to the DB60 Goose neck bracket or EMT pipe
threads (if using) and tighten the provided tapping screws to fully compress the ‘O’ ring.
• Ensure that the mounting surface and mounting hardware is suitable for the chosen installation
method.
• To maintain IP67 waterproof rating, always use the waterproof RJ45 connector (Figure C).
• Use sealant on all threads during installation.
• Use a network cable 5mm or more in diameter to create a good seal in RP1 (if using).
DB60 / Pendant Installation (Follow Figure B)
Note: Do not drill any holes in B88.
1. Remove RP1 (rubber plug) from the B88.
2. Pull the camera’s cable through B88 opening and into the DB60 or the 3/4 EMT pipe.
3. Attach B88 to the DB60 or to the 3/4” EMT pipe (using a conduit fitting).
Add sealant as shown in Figure B
4. Use machine type screws (1) to attach Ax88 camera to the B88 back box.
Re-attach the dome cover.
Figure A. B88 Dimensions
Figure B. B88, mounting diagram.
Diameter
5 1/8”
(130.5 mm)
Height
1 9/16”
(40 mm)
Rubber
gasket
RP1. 3/4”
waterproof
rubber plug Cable
retention clip
3
12
Up
Lens Direction
GUIDE PATTERN
4
WATERPROOF RJ45 CONNECTOR
Waterproof
RJ45
connector
B88
Back box
Dome
cover
INSTALLATION
Use the security Torx bit or screwdriver (not provided) to loosen three screws securing the
dome cover to Ax88 camera. Set the cover aside.
Surface Installation
1. B88 comes with six 90% pre-drilled hole dimples.
Depending on the type of installation and mounting surface, complete drilling 2-3 holes.
2. Attach the mounting template (4) to the mounting surface.
3. Drill holes, as marked on the template, to match the holes pre-drilled on the back box in
Step 1.
4. Insert anchors (3) into the holes.
5. Drill the conduit hole for the camera cable, as marked on the template; pull the camera’s
cable into the B88 back box.
6. Secure the B88 back box to mounting surface using the screws with the O-ring (2).
Tighten to fully compress the ‘O’ ring.
7. Use machine type screws (1) to attach Ax88 camera to the B88 back box.
8. Re-attach the dome cover.
STEP 1
STEP 2
STEP 3
STEP 4
Figure C. RJ45 waterproof connector assembly.
  • Page 1 1

i3 International B88 User manual

B88
i3 International
Brand
i3 International
Model
B88
Category
Security camera accessories
Type
User manual

i3 International B88 is an extension back box designed for cable management and mounting of i3's Ax88 12MP Fisheye camera. It features six pre-drilled hole dimples for surface mounting and can be used for outdoor and indoor installations. The B88 provides a waterproof solution with an IP67 rating when used with the included waterproof RJ45 connector and sealant. It also allows for flexible mounting options with the DB60 Horizontal Wallmount bracket or Pendant Mount EMT Pipe (sold separately).

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents