Extron electronic AAP TX/RX User manual

Extron electronic
Brand
Extron electronic
Model
AAP TX/RX
Category
Interface hubs
Type
User manual

This manual is also suitable for

1
USB Extenders • Setup Guide
This guide provides basic instructions for an experienced technician to install and operate
the Extron USB Extenders.
USB USB
HUB
1
2
3
4
POWER
12V
1.0A MAX.
LINK
DO NOT
CONNECT
TO LAN
HOST
POWER
12V
0.4A MAX.
DO NOT
CONNECT
TO LAN
LINK
Ground
+12 VDC
External
Power Supply
(12 VDC, 1 A )
Ground
+12 VDC
External
Power Supply
(12 VDC, 1 A )
Keyboard
Laptop
Four USB 2.0 compatible type A female
connectors provide +5 VDC at up to
500 mA to connected USB peripherals.
If the USB host is capable of supplying power,
a transmitter power supply is not required.
The receiver must have a power supply connected.
Transmitter Receiver
UTP or STP CAT5 or better cable:
Te rminate both ends identically, in accordance with
either the TIA/EIA T 568A or the TIA/EIA T 568B
wiring standard.
Run All Cables
Connect the transmitter and receiver as shown above.
NOTE: The host and hub connectors of the AAP and Decora models are on the front panel. The host
connection on the AAP and Decora transmitter is a female mini USB Type B. Connection and operation
are the same as the rack mount Tx/Rx models.
The USB Extender Series includes the USB Extender Tx/Rx, AAP Tx/Rx, and Decora
®
Tx/Rx. They are USB transmitter and
receiver pairs that extend the usable distance of USB 1.0, 1.1, and 2.0 standards with data transfer rates up to 480 Mbp and
data transmission up to 450 ft (135 m) with standard Category 5/5e/6/6e/7 cable.
The rack mountable Tx/Rx, AAP mountable Tx/Rx, and Decora Tx/Rx models can be mixed.
Mount the USB Extenders
The USB Extender series includes transmitters and receivers in three form factors to provide a variety of mounting options
including:
z USB Extender Tx/Rx in quarter rack width, 3 inch deep, 1 inch high metal enclosures
z USB Extender AAP Tx/Rx for double-space Architectural Adapter Plate openings
z USB Extender D (Decora) Tx/Rx for one-gang wall box or mud ring mounting
Choose the appropriate mounting location and install the USB Extender transmitter and receiver following instructions
supplied with the mounting kit. If the rear panel connectors will be covered after mounting, make all connections prior to
permanently mounting a USB Extender.
2
68-1719-50
Rev. D 09 11
USB
CAT 5/5e/6/7
up to 450' (135m)
HUB
1
2
3
4
POWER
12V
1.0A MAX
LINK
DO NOT
CONNECT
TO LAN
HOST
POWER
12V
0.4A MAX
DO NOT
CONNECT
TO LAN
LINK
50/60Hz
100-240V .5A MAX
RS-232
RS-232
KEYBOARD
MOUSE
USB
RESET
LAN
RGB/R-Y,Y,B-Y
RGB/R-Y,Y,B-Y
R/
R-Y
B/
B-Y
H
V
S
G/
Y
HDSDI/
SDI
RGB/R-Y, Y, B-Y
4 5 7
6
3
1
2
R/
R-Y
G/Y
VID
H/HV V CR-Y
B/C
B-Y
B-Y
/C
VID
/Y
VID
/Y
O
U
T
P
U
T
S
I
N
P
U
T
S
DVI-D
MTP
DVI
OUT
Extron
Annotator
Annotation Graphics
Processor
Projector/Display
USB Touchscreen
Display
USB
Extron
USB Extender TX
Twisted Pair Transmitter
for USB Peripherals
Extron
USB Extender RX
Twisted Pair Receiver
for USB Peripherals
HOST
USB EXTENDER AAP Tx
ACTIVITY
LINK HOST
USB EXTENDER AAP Rx
HUBACTIVITY
LINK
1
2
1
HOST
2
3
4
3
4
LINK
HOST
ACTIVITY
LINK
ACTIVITY
1
HOST
2
3
4
USB Extender Rx
USB Extender Tx
Transmitters
Receivers
USB Extender Tx D
a
b
c
USB Extender Rx D
a
b
c
b
c
d
abc
abc
bac
d
Apply Power to the USB Extenders
1. Connect the external power supply to the receiver.
The power LED (
a
) on the receiver lights when power is applied.
2. Connect power to the transmitter depending upon the power source.
z If using an external supply the power LED (
a
) of the transmitter lights when power is properly applied. The Link
LED (
b
) on both the transmitter and receiver also lights to indicate proper link cable connection, or
z If using a computer USB port to power the transmitter, the transmitter Power and Link LEDs do not light until after
the laptop or PC is powered and booted up. The receiver Link LED lights once the transmitter is powered.
Connect the Host (Transmitter)
1. Connect a USB cable from the PC or laptop USB port to the
transmitter Host port as shown on the previous page. The AAP and
Decora transmitters have a female mini USB Type B connector on the
front panel for this connection.
2. Reboot or power up the PC or laptop. The Host LED on the front
panel of the transmitter (
c
) lights when the PC recognizes the port.
If the PC is supplying transmitter power, the transmitter and receiver
Link LEDs (
b
) both light.
Connect the Hub (Receiver)
1. Connect up to four USB cables from peripheral devices to the
receiver Hub ports. The order of connection does not matter.
The Host LED on the receiver (
c
) lights as communications between
the USB transmitter and host occur.
2. As each peripheral is connected, the LED for the appropriate hub
port (
d
) lights when the PC has detected the device.
NOTE: The USB Extender receivers can supply up to 0.5 A to
each connected peripheral.
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
  • Page 1 1
  • Page 2 2

Extron electronic AAP TX/RX User manual

Extron electronic
Brand
Extron electronic
Model
AAP TX/RX
Category
Interface hubs
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents