2. Extron electronics
  3. Style1-Gang
Style1-Gang

Extron electronics Style1-Gang, Decora Style1-Gang Wallplate WP CTL D, WP CTL D User manual

  • Hello! I am an AI chatbot trained to assist you with the Extron electronics Style1-Gang User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1. Using a mud ring or a junction box as a guide, mark the holes and cut out the
material within the marked area.
N
If installing a junction box, allow enough depth for
the wall plate and cables.
The box should be at least 2.0” (5.1 cm) deep to
accommodate the connectors, plate, and cables.
2. Either
•Insertthemudringintotheopening,rotate
thedoglegs,andsecurewiththescrewsprovided,
or
•Insertthewallboxandsecurewith10-pennynails
or screws.
3. RuntheRS-232andIRsignalcablesbehindthewall
and thread them through the mud ring or wall box.
N Extron recommends using a good quality, low
capacitance, shielded cable such as an Extron
CTL or SPL Control cable.
Decora
Faceplate
Extron
WP CTL D
Wall
Wall Mounting
Bracket
G
S
IR
G
Rx
Tx
Serial
WP CTL D Installation Guide
TheExtronWPCTLDisaDecorastyle1-gangwallplatewhichpassesRS-232controlsignals
fromacomputerorcontrolsystem,andIRsignalsfromanIRsource.
Installitdirectlyintothewallusingamudring,orina1-gangjunctionbox(notsupplied),
followingthestepsbelow.
4. ConnecttheIRcabletotherearpanelIR
connectorbyinsertingthesignalwireinto
the hole marked "S" , and the ground wire
intotheholemarked"G"(seeinset,step4).
N
The recommended driving distance from
an MLC controller is 100 feet.
5. ConnecttheRS-232cabletotherearpanelRS-232
connectorbyinsertingthegroundwireintothehole
marked "G", the transmit wire into the hole marked
"Tx",andthereceivewireintotheholemarked
"Rx"(seeinset,step5).
6. Mountthedeviceintothemudringorwallbox.
7. AttachthesuppliedDecorafaceplate.
N If applicable, repeat steps 1-7 to install additional wall plates.
8. ConnecttheRS-232controldeviceand/orIRinputdevicetothefrontoftheWPCTLD.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Dubai
+971.4.2991800
+971.4.2991880 FAX
68-1618-01
Rev B 08 08
WP CTL D Installation Guide, cont’d
Step 5
Step 4
G
Tx
Rx
WP CTL D
IR Out
White striped wire
S = Signal (IR)
G = Ground
G S
IR Emitter
100'
(30.5 m)
/