Extron AAP 100 MD User manual

Brand: Extron

Model: AAP 100 MD

Type: User manual

Extron AAP 100 MD is an Architectural Adapter Plate that can have up to two architectural adapter plates installed, depending on the configuration selected. It can be used to replace an old adapter plate or blank plate. The AAP bracket can accommodate up to two single spaced AAPs or one double spaced AAP. It is designed to be installed in a Matsushita Denko (MD) floor box and provides a convenient way to connect cables and devices to the floor box. The AAP 100 MD is easy to install and comes with all the necessary mounting hardware.

User’s Guide

MD Floor Box AAP Bracket Installation Kit

AAP 100 MD

68-720-01 Rev. B

11 08

MD Floor Box AAP Kit • Installation

Installation

3. Remove Screws

4. Slide

Introduction

This guide covers installation of the Extron MD Floor Box AAP

Bracket Kit in a Matsushita Denko (MD) ﬂoor box. It shows

removal of the old bracket and installation of the new

bracket/AAP unit.

Installation

Installation and service must be performed by

authorized personnel only.

1. Turn off and disconnect power from all

equipment connected to the ﬂoor box.

2. Remove all cables connected

to the portion of the

ﬂoor box accessible

when the lid is open (if

applicable).

3. Open the lid and remove

the two screws securing

the lid to the ﬂoor box.

4. Remove the lid from

the ﬂoor box by

sliding the lid

toward the hinge to

disengage it from the

box, then put the lid aside.

If there is no adapter plate or blank plate installed, skip to

step 8.

5. Remove the two screws securing the old adapter plate

bracket to the box.

5. Remove Screws

6. Slide the adapter plate bracket to the center of the box

and disconnect the cables attached to the back side of the

adapter plate.

7. Remove the old adapter plate bracket and adapter plate

unit from the ﬂoor box.

MD Floor Box AAP Kit • Installation

8. Attach and secure any single or double Extron AAP (for

example, the double AAP shown below) to the MD AAP

bracket with the 4‑40 mounting nuts provided.

9. Connect cables, if applicable, to the back of the AAP to be

installed.

10. Slide Bracket

10. Place the MD AAP bracket into the ﬂoor box (as shown

above), routing any cables through the back of the box and

slide it in the direction shown.

11. Attach with

M4 Screws

11. Align the two screw holes in the top of the new AAP

bracket with the holes in the box. Attach the bracket with

the two M4 screws provided.

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714 .491.1500

+1.714 .491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron EMEA

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Installation, cont'd

12. Place the lid on the ﬂoor box and slide it away from the

hinge to engage the tabs on the box.

13. Reinstall the two previously removed screws, securing the

lid to the box.

13. Replace Screws

12. Slide

14. Reconnect power and cables, as necessary.

Optional Extron Architectural Adapter Plates

A variety of optional architectural adapter plates for

pass‑through connections may be ordered for the MD ﬂoor box

AAP bracket. Visit the Extron website at www.extron.com for

additional information.

The AAP bracket can have up to two architectural adapter plates

installed, depending on the conﬁguration selected.

The following conﬁgurations of architectural adapter plates

could be installed in the MD ﬂoor box adapter plate:

• two single spaced AAPs

• one double spaced AAP

Extron AAP 100 MD User manual

Extron AAP 100 MD User manual

Extron AAP 100 MD User manual

Related papers

Other documents