Herman Miller My Studio Environments Product Instructions

Herman Miller
Brand
Herman Miller
Model
My Studio Environments
Type
Product Instructions

Herman Miller My Studio Environments is a versatile and customizable workspace solution that can be tailored to your specific needs. With its modular design, you can easily add or remove components to create the perfect layout for your space. The Primary Surface Support Assembly is a key component of the My Studio Environments system, providing a sturdy and supportive base for your worksurface. It is easy to install and can be adjusted to the desired height.

Herman Miller My Studio Environments is a versatile and customizable workspace solution that can be tailored to your specific needs. With its modular design, you can easily add or remove components to create the perfect layout for your space. The Primary Surface Support Assembly is a key component of the My Studio Environments system, providing a sturdy and supportive base for your worksurface. It is easy to install and can be adjusted to the desired height.

My Studio Environments®
Primary Surface Support
Installation
A 1BKY8 RLS FOR PROD MEK JI 03/04/05
INSTRUCTIONS-
PRIMARY SURFACE SUPPORT INSTALLATION
MAKE FROM 115160
MEK 03/03/05 JI 03/03/05
JO 11/20/07
15
1B1RFS
1B1RFS
REV PROD NAME MEK PG 04/21/06
1BSKRB
C1BY70RMV PART F; REV STEP 1 MEK KF 3/28/07
D 1C1GG PART “H” QTY WAS 11 OR 15 MEKJO 11/20/07
1B1RFS REV D
My Studio Environments® Primary Surface Support Installation
End Support (2)
Leg Support
Main Support
Post Support
Hardware Pack
Parts Included:
A
BC
D
E
Street-Side Support
5/8” Long Cap
G1 3/4” Long Flange 7/8” Long Flange
Screw (6) Screw (10) Screw (8)
HI
Primary Surface Support Assembly
1
1. Position End Support between Side Wall Frame and Wall Cladding.
2. Measure from floor to top edge of End Support for desired worksurface height.
3. Install (2) 5/8” long Cap Screws. DO NOT TIGHTEN!
A
Tools Required:
Power Driver 3/16 Hex Bit 3/16 Hex Key
NOTICE!
Make all electrical connections and
before installation.
G
4. Repeat process at other end of Side Wall.
Level install lower Cladding inside office area
IMPORTANT: Save these instructions for layout changes.
1B1RFS REV D
2
3
D
B
Hole
1. Assemble Main Support onto
End Supports. Make sure
1. Insert Streetside Support completely into Main Support.
Spring Pins engage into detent
holes.
Spring Pin
1. Tighten all End Support Screws.
G
4
5
1. Extend Streetside Support until detent engages.
2. Secure Streetside Support to Streetside Tube with (2) Cap Screws.
Streetside
Screws
Support
1B1RFS REV D
7
6
End Support Detent
End Cap
Front Leg
1. Remove End Caps from Front Legs
of Bookcase.
1. Insert Leg Support into End
Support. Make sure Spring Pins
engages at first detent location
C Use second detent location for
6’ office.
Detent
for 8’ and 10’ office.
9
1. Insert Post Support into Bookcase Leg.
8
1. Slide Bookcase into position with
E
Bookcase
Leg
Make sure Spring Pins engage into desired
Leg Support inserted into Post
Support. Make sure Spring Pins
engage.
height.
1B1RFS REV D
12
1. Install (10) 1 3/4” long Flange Head Screws through square tubing in Support
2. Install at least (4) 7/8” long Flange Head Screws at Bookcase Leg location.
HI
Assembly.
10
1. Level Support Assembly by adjusting the Guide on Bookcase.
1. Place Work Surface on top of Support Assembly.
11
2. Push back edge of Work Surface against Locator on End Support and side edge
against Streetside Support Tubes.
Locator
Support Tube
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Herman Miller My Studio Environments Product Instructions

Herman Miller
Brand
Herman Miller
Model
My Studio Environments
Type
Product Instructions

Herman Miller My Studio Environments is a versatile and customizable workspace solution that can be tailored to your specific needs. With its modular design, you can easily add or remove components to create the perfect layout for your space. The Primary Surface Support Assembly is a key component of the My Studio Environments system, providing a sturdy and supportive base for your worksurface. It is easy to install and can be adjusted to the desired height.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents