Herman Miller My Studio Environments Product Instructions

Herman Miller
Brand
Herman Miller
Model
My Studio Environments
Type
Product Instructions

Herman Miller My Studio Environments provides you with the flexibility to create a customized and functional workspace that meets your specific needs. With its modular design, you can easily adapt the system to accommodate changes in your workflow or space requirements. The Secondary Surface Support feature allows you to add an additional work surface to your existing configuration, providing you with extra space for projects, equipment, or storage.

Herman Miller My Studio Environments provides you with the flexibility to create a customized and functional workspace that meets your specific needs. With its modular design, you can easily adapt the system to accommodate changes in your workflow or space requirements. The Secondary Surface Support feature allows you to add an additional work surface to your existing configuration, providing you with extra space for projects, equipment, or storage.

My Studio Environments™
Secondary Surface Support
Installation
A 1BKY8 RLS FOR PROD MEK JI 03/04/05
INSTRUCTIONS-
SECONDARY SURFACE SUPPORT INSTALLATION
MAKE FROM 115160
MEK 03/03/05 JI 03/03/05
KEF 03/28/07
14
1B267D
1B267D
REV PROD NAME MEK PG 04/21/06
1BSKRB
C1BY70RMV PART E, REV STEP 1 MEK KF 3/28/07
1B267D REV C
My Studio Environments™ Secondary Surface Support
Installation
Tools Required:
Power Driver
Leg Support
Main Support
Post Support
Hardware Pack
3/16 Hex Bit
Parts Included:
B
C
D5/8” Long Cap
F1 3/4” Long Flange 7/8” Long Flange
3/16 Hex Key
Screw (4) Screw (9) Screw (8)
GH
End Support (2)
A
Level
Counter Top Support
1
1. Position End Support between Side Wall Frame and Wall Cladding.
2. Measure from floor to top edge of End Support for desired worksurface height.
3. Install (2) 5/8” long Cap Screws. DO NOT TIGHTEN!
AF
4. Repeat process at other end of Side Wall.
NOTICE!
Make all electrical connections and
before installation.
Notch
NOTE: For Work Surfaces being installed at 28 1/2”, install End Support with the top
Screw mounted in hole with notch in Side Wall Frame.
install lower Cladding inside office area
IMPORTANT: Save these instructions for layout changes.
1B267D REV C
2
Hole
1. Assemble Main Support onto
End Supports. Make sure
Spring Pins engage into detent
holes.
Spring Pin
1. Tighten all End Support Screws.
3
Screws
5
1. Insert Leg Support into End Support.
4
Make sure Spring Pins engage at last
hole location.
C
End Support
Hole
End Cap
Front Leg
1. Remove End Caps from Front Legs
of Bookcase.
1B267D REV C
3. Install 1 3/4” long Flange Head Screws through square tubing in Support Assembly.
4. Install at least (4) 7/8” long Flange Head Screws at Bookcase Leg location.
G
H
1. Place Work Surface on top of Support Assembly.
7
2. Push back edge of Work Surface against Locator on End Support and side edge
against Support Bracket mounted on Back Panel of Closet.
Locator
Support Bracket
Closet Back Panel
1. Insert Post Support into Bookcase Leg.
6
D
Bookcase
Leg
Make sure Spring Pins engage.
2. Slide Bookcase into position with Leg
Support inserted into Post Support. Ma
k
sure Spring Pins engage.
3. Level Support Assembly by adjusting the
Glide on Bookcase.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Herman Miller My Studio Environments Product Instructions

Herman Miller
Brand
Herman Miller
Model
My Studio Environments
Type
Product Instructions

Herman Miller My Studio Environments provides you with the flexibility to create a customized and functional workspace that meets your specific needs. With its modular design, you can easily adapt the system to accommodate changes in your workflow or space requirements. The Secondary Surface Support feature allows you to add an additional work surface to your existing configuration, providing you with extra space for projects, equipment, or storage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents