2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.
, Abak, Action Office, Avive, Co/Struc, Ethospace, Intersect, Meridian, Passage, Prospects, Quadrant, Resolve, Scooter, Vivo interiors, and V-Wall are among the
registered trademarks of Herman Miller Inc.
Burdick Group, CLT, Flex-Edge, My Studio Environments, Lifework, Q system, and Teneo are among the trademarks of Herman Miller Inc.
Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make changes in design and specifications
at any time, without notice, and also to discontinue products.
©
®
™
My Studio Environments
™
Streetside Straight Frame
Installation
A1BKLVRLS FOR PROD MEK KF 12/27/04
INSTRUCTIONS-
STREETSIDE STRAIGHT FRAME INSTALLATION
MAKE FROM 115160
MEK 12/27/04 KF 12/27/04
KF 02/15/07 KF
14
1B25BH
1B25BH
2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.
, Abak, Action Office, Avive, Co/Struc, Ethospace, Intersect, Meridian, Passage, Prospects, Quadrant, Resolve, Scooter, Vivo interiors, and V-Wall are among the
registered trademarks of Herman Miller Inc.
Burdick Group, CLT, Flex-Edge, My Studio Environments, Lifework, Q system, and Teneo are among the trademarks of Herman Miller Inc.
Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make changes in design and specifications
at any time, without notice, and also to discontinue products.
©
®
™
REV PROD NAME MEK PG 04/21/06
1BSKRB
C1BTMVADDED ITEMS J, K, L & SH 4 MEK KF 7/19/06
D 1BXKX REV PART E & STEP 5 PIX MEKKEF 02/15/07
E1C4PH REMOVE PARTS E, G, & I RB GD 9/02/08
1B25BH REV E
2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.
, Abak, Action Office, Avive, Co/Struc, Ethospace, Intersect, Meridian, Passage, Prospects, Quadrant, Resolve, Scooter, Vivo interiors, and V-Wall are among the
registered trademarks of Herman Miller Inc.
Burdick Group, CLT, Flex-Edge, My Studio Environments, Lifework, Q system, and Teneo are among the trademarks of Herman Miller Inc.
Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make changes in design and specifications
at any time, without notice, and also to discontinue products.
©
®
™
My Studio Environments
™
Streetside Straight Frame
Installation
Tools Required:
Support Tube
5/16 Allen
Parts Included:
A
Connector
H
Plate (3)
Cross Tube (3)
B
Draw Rod (3)
C
Screw (12) Tube Joint
Connector (6)
DF
Hardware Pack
Torque5/32 Allen 5/16 Hex
1
1. From inside of office, assemble Connector
Plates to Tube Connectors with 4 Screws.
HD
F
Joint Connection
Wrench Wrench Wrench Socket
Screw
L
Straight Top Cap
J
Screw Cap
K
46” only 46” only
46” only
46” (8) 46” (4) 46” (2)
46” (2) 46” (2)
1. Assemble Tube Connectors, Cross Tubes and Support Tube with Draw Rods as
F
B
C
B
B
A
C
C
F
A
F
C
B
shown. Tighten Draw Rods to 150 in-lbs.
Tab
2
Not used
for 46”
Not used
for 46”
Not used
for 46”
IMPORTANT: Save these instructions for layout changes.
1B25BH REV E
2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.
, Abak, Action Office, Avive, Co/Struc, Ethospace, Intersect, Meridian, Passage, Prospects, Quadrant, Resolve, Scooter, Vivo interiors, and V-Wall are among the
registered trademarks of Herman Miller Inc.
Burdick Group, CLT, Flex-Edge, My Studio Environments, Lifework, Q system, and Teneo are among the trademarks of Herman Miller Inc.
Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make changes in design and specifications
at any time, without notice, and also to discontinue products.
©
®
™
1. Install End Cladding Bracket (supplied with curved frame) by inserting Post on Bracket
6
2. Install Screw into end of Bracket 3 places.
Opening
Post
5
1. Position Attachment Clip to Tube Connectors.
Tube Connectors
2. Insert Clip Fastener through Attachment Clip and between Tube Connectors.
Tab
into opening in Tube connector.
End Cladding
Screw
Bracket
Joint Connection
End Connection
Retaining Feature
3. Rotate Clip Fastener 1/4 turn clockwise.
4. Align Tabs on Cladding Bracket with Retaining Feature on Attachment Clip. Press
down to fully engage Tabs.
Clip Fastener
Attachment
Clip Fastener
Clip
3
End Connection
D
1. Install Cladding. See Instruction Sheet 1B2H19 for
4
Cladding
1. Install 2 Screws into Tube Connectors.
details.
1B25BH REV E
2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.
, Abak, Action Office, Avive, Co/Struc, Ethospace, Intersect, Meridian, Passage, Prospects, Quadrant, Resolve, Scooter, Vivo interiors, and V-Wall are among the
registered trademarks of Herman Miller Inc.
Burdick Group, CLT, Flex-Edge, My Studio Environments, Lifework, Q system, and Teneo are among the trademarks of Herman Miller Inc.
Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make changes in design and specifications
at any time, without notice, and also to discontinue products.
©
®
™
7
46” Product only:
1. Place Straight Top Cap (J) on top of Cladding.
1. Install Cladding before Straight Top Cap.
8
J
Cladding
See instruction sheet 1B2H19 for details.
9
1. Place End Cap, supplied with Curved Frame, into end of Tube.
2. Insert Screw Cap, supplied with Curved Frame, into End Cap and Curve Top Cap.
3. Install Screw supplied with Curved Frame. Torque Screw to 80 in-lbs.
1. Insert Screw Cap (K) into joint of Straight and Curve Top Caps.
2. Install Screw (L). Torque Screw to 80 in-lbs.
10
L
K
End
Cap Screw
Cap Screw
/
